Condensation starts ________ point. A] Dew point B] Bubble point C] Triple point D] None of the mentioned

Condensation starts ________ point.
A] Dew point
B] Bubble point
C] Triple point
D] None of the mentioned
by

1 Answer

Answer :

A] Dew point
by

Related questions

Condensation starts at ________ point. A Dew B Bubble C Triple D none of the mentioned

Description : Condensation starts at ________ point. A Dew B Bubble C Triple D none of the mentioned

Last Answer : A Dew

When gas changes to liquid through the process of condensation, the temperature A] Increases. B] Decreases C] Remains constant. D] None of the mentioned

Description : When gas changes to liquid through the process of condensation, the temperature A] Increases. B] Decreases C] Remains constant. D] None of the mentioned

Last Answer : C] Remains constant.

In a condensation process, _______ to _________ A] Gas, Solid B] Gas, Liquid C] Liquid, Gas D] Liquid, Solid

Description : In a condensation process, _______ to _________ A] Gas, Solid B] Gas, Liquid C] Liquid, Gas D] Liquid, Solid

Last Answer : B] Gas, Liquid

What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Description : What is the temperature at which the water vapour in the mixture of water vapour in air, starts condensing called? A. condensation temperature B. dew point temperature C. vaporization temperature D. all of the above

Last Answer : ANSWER : B

When the bubbles of steam are produced? • Once the water reaches saturation temperature • Once the water starts evaporating • Once the temperature decreases • None of the above

Description : When the bubbles of steam are produced? • Once the water reaches saturation temperature • Once the water starts evaporating • Once the temperature decreases • None of the above

Last Answer : • Once the water reaches saturation temperature

The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Description : The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Last Answer : (B) Less than

Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Description : Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Last Answer : • Steam turbine

Condensate is the liquid formed when steam passes from the ________ to the ______ state. a. Vapor, solid b. Solid, liquid c. Vapor, liquid d. None

Description : Condensate is the liquid formed when steam passes from the ________ to the ______ state. a. Vapor, solid b. Solid, liquid c. Vapor, liquid d. None

Last Answer : c. Vapor, liquid

A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Description : A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Last Answer : c. Combustion, transfers

A -________ incorporates a firebox or furnace in order to burn the fuel and _________ heat. a. Boiler, generate b. Heat, boiler c. Steam, pressure d. None

Description : A -________ incorporates a firebox or furnace in order to burn the fuel and _________ heat. a. Boiler, generate b. Heat, boiler c. Steam, pressure d. None

Last Answer : a. Boiler, generate

The product of efficiency & heat transferred to the working fluid is? a. Net temperature change b. Net work done c. Net enthalpy change d. None of the mentioned

Description : The product of efficiency & heat transferred to the working fluid is? a. Net temperature change b. Net work done c. Net enthalpy change d. None of the mentioned

Last Answer : b. Net work done

When vapour is cooled at constant total system volume, the _______ changes. A] Volume. B] Pressure C] Temperature. D] None of the mentioned

Description : When vapour is cooled at constant total system volume, the _______ changes. A] Volume. B] Pressure C] Temperature. D] None of the mentioned

Last Answer : B] Pressure

When vapour is compressed isothermally the ____________ changes. A] Volume. B] Pressure C] Temperature D] None of the mentioned

Description : When vapour is compressed isothermally the ____________ changes. A] Volume. B] Pressure C] Temperature D] None of the mentioned

Last Answer : A] Volume.

Green coal, in order to be burnt, must be (A) Heated sufficiently (B) Burnt in excess air (C) Heated to its ignition point (D) Burnt as powder

Description : Green coal, in order to be burnt, must be (A) Heated sufficiently (B) Burnt in excess air (C) Heated to its ignition point (D) Burnt as powder

Last Answer : (C) Heated to its ignition point

A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Description : A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Last Answer : c. Steam boiler

__________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Description : __________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Last Answer : (A) Dew point

In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Description : In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for ... bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Last Answer : (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column

_________ is the temperature to which the air must be cooled, at constant pressure, to produce saturation.  a. relative humidity  b. triple point temperature  c. dew point  d. critical point

Description : _________ is the temperature to which the air must be cooled, at constant pressure, to produce saturation.  a. relative humidity  b. triple point temperature  c. dew point  d. critical point

Last Answer : dew point

What has to happen for Condensation to occur in nature air must be cooled to its dew point and there must be some kind of solid surface present true or false?

Description : What has to happen for Condensation to occur in nature air must be cooled to its dew point and there must be some kind of solid surface present true or false?

Last Answer : 1

Water vapour beyond the dew point result in A. Precipitation B. Hailstorm C. Condensation D. Formation of ice

Description : Water vapour beyond the dew point result in A. Precipitation B. Hailstorm C. Condensation D. Formation of ice

Last Answer : ANSWER: C

On large generators, space heaters are used to ____________. A. keep the machine at ambient tmperature of the machinery space B. maintain rotor and stator winding temperatures above the dew point to prevent the formation of condensation C. prevent condensation in the lube oil D. prevent electrolysis due to condensation in the bearings

Description : On large generators, space heaters are used to ____________. A. keep the machine at ambient tmperature of the machinery space B. maintain rotor and stator winding temperatures above the dew point ... C. prevent condensation in the lube oil D. prevent electrolysis due to condensation in the bearings

Last Answer : Answer: B

Water vapour beyond the dew point result in-----? A. Precipitation B. Hailstorm C. Condensation (Answer) D. Formation of ice

Description : Water vapour beyond the dew point result in-----? A. Precipitation B. Hailstorm C. Condensation (Answer) D. Formation of ice

Last Answer : C. Condensation (Answer)

Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Description : Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Last Answer : (D) Dew point temperature

What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Description : What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Last Answer : c. Formation of bubbles

Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Description : Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Last Answer : d. Outside the boiler

What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Description : What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Last Answer : a. Saturated steam

In which year was Lamont boiler invented? a. 1905 b. 1910 c. 1920 d. 1925

Description : In which year was Lamont boiler invented? a. 1905 b. 1910 c. 1920 d. 1925

Last Answer : d. 1925

What is the pressure range between which Lamont boiler operator ? a. 80-120 bar b. 120-160 bar c. 180-360 bar d. 450-560 bar

Description : What is the pressure range between which Lamont boiler operator ? a. 80-120 bar b. 120-160 bar c. 180-360 bar d. 450-560 bar

Last Answer : b. 120-160 bar

Through which does the even circulation of water is possible in Lamont boiler ? a. Nozzles b. Water trough c. Feed pump d. Hose

Description : Through which does the even circulation of water is possible in Lamont boiler ? a. Nozzles b. Water trough c. Feed pump d. Hose

Last Answer : a. Nozzles

In what form are the boiler tube arrange in Lamont boiler ? a. Parallel in vertical b. Inclined vertically c. Parallel in horizontal d. Horizontally inclined

Description : In what form are the boiler tube arrange in Lamont boiler ? a. Parallel in vertical b. Inclined vertically c. Parallel in horizontal d. Horizontally inclined

Last Answer : c. Parallel in horizontal

Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Description : Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Last Answer : b. Economizer

What is called as the heart of the Lamont boiler? a. Water drum b. Centrifugal pump c. Furnace d. Blower

Description : What is called as the heart of the Lamont boiler? a. Water drum b. Centrifugal pump c. Furnace d. Blower

Last Answer : b. Centrifugal pump

Type of Lamont boiler is_______ a. Forced circulation b. Natural circulation c. Over-through d. Positive forced circulation

Description : Type of Lamont boiler is_______ a. Forced circulation b. Natural circulation c. Over-through d. Positive forced circulation

Last Answer : a. Forced circulation

Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Description : Boilers are used in places like 1. Domestic heating 2. Commercial heating 3. Industrial heating application 4. All of above

Last Answer : 4. All of above

Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Description : Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Last Answer : 4. All of above

Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Description : Boiler works from application of which type of energies 1. Fuel combustion 2. Electricity 3. Nuclear energy 4. All of above

Last Answer : 4. All of above

High pressure boilers operate at 1. Lower than 15 psig 2. Higher than 15 psig 3. 15 psig 4. None of above

Description : High pressure boilers operate at 1. Lower than 15 psig 2. Higher than 15 psig 3. 15 psig 4. None of above

Last Answer : 2. Higher than 15 psig

Boiler is a enclosed vessel that provides a) Expansion b) Ignition c) Combustion d) None of the above

Description : Boiler is a enclosed vessel that provides a) Expansion b) Ignition c) Combustion d) None of the above

Last Answer : c) Combustion

Foaming is caused by the formation of ___________ a) Acids b) Alcohols c) Oils and alkalis d) Ketones

Description : Foaming is caused by the formation of ___________ a) Acids b) Alcohols c) Oils and alkalis d) Ketones

Last Answer : c) Oils and alkalis

The phenomenon during which the boiler material becomes brittle due to accumulation of caustic substances is known as ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Description : The phenomenon during which the boiler material becomes brittle due to accumulation of caustic substances is known as ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Last Answer : d) Caustic embrittlement

The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Description : The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Last Answer : b) Priming

Which of the following option is incorrect about the sludges? a) Sludges are soft, loose and slimy precipitate b) They are non-adherent deposits and can be easily removed c) Formed generally at heated portions of the boiler d) Can be removed by blow down operation

Description : Which of the following option is incorrect about the sludges? a) Sludges are soft, loose and slimy precipitate b) They are non-adherent deposits and can be easily removed c) Formed generally at heated portions of the boiler d) Can be removed by blow down operation

Last Answer : c) Formed generally at heated portions of the boiler

If the precipitate formed is soft, loose and slimy, these are __________ and if the precipitate is hard and adhering on the inner wall, it is called _____________ a) Sludges, scale b) Scale, sludges c) Sludges, rodent d) Scale, rodent

Description : If the precipitate formed is soft, loose and slimy, these are __________ and if the precipitate is hard and adhering on the inner wall, it is called _____________ a) Sludges, scale b) Scale, sludges c) Sludges, rodent d) Scale, rodent

Last Answer : a) Sludges, scale

Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Description : Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Last Answer : b) Decomposition

A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Description : A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Last Answer : (B) 90°

The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Description : The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Last Answer : (A) 0.4

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Description : In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Last Answer : (D) 0.067 bar

Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Description : Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Last Answer : (D) Clean the nozzles

Adiabatic process is (A) Essentially an isentropic process is___________ (B) Non-heat transfer process (C) Reversible process (D) Constant temperature process

Description : Adiabatic process is (A) Essentially an isentropic process is___________ (B) Non-heat transfer process (C) Reversible process (D) Constant temperature process

Last Answer : (B) Non-heat transfer process