A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion.
(A) 60°
(B) 90°
(C) 180°
(D) 270°
by

1 Answer

Answer :

(B) 90°
by

Related questions

The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Description : The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Last Answer : (A) 0.4

Number of degree a complete circle represents is A. 90° B. 180° C. 270° D. 360°

Description : Number of degree a complete circle represents is A. 90° B. 180° C. 270° D. 360°

Last Answer : 360°

In vibration isolation system, if ω/ωn, then the phase difference between the transmitted force and the disturbing force is A 0° B 90° C 180° D 270°

Description : In vibration isolation system, if ω/ωn, then the phase difference between the transmitted force and the disturbing force is A 0° B 90° C 180° D 270°

Last Answer : C 180°

In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is A. 0° B. 90° C. 180° D. 270°

Description : In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is A. 0° B. 90° C. 180° D. 270°

Last Answer : C. 180°

In vibration isolation system, if ω/ω n , then the phase difference between the transmitted force and the disturbing force is a) 0° b) 90° c) 180° d) 270°

Description : In vibration isolation system, if ω/ω n , then the phase difference between the transmitted force and the disturbing force is a) 0° b) 90° c) 180° d) 270°

Last Answer : c) 180°

In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is a) 0° b) 90° c) 180° d) 270°

Description : In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is a) 0° b) 90° c) 180° d) 270°

Last Answer : c) 180°

Back bearing of a line is equal to (A) Fore bearing ± 90° (B) Fore bearing ± 180° (C) Fore bearing ± 360° (D) Fore bearing ± 270°

Description : Back bearing of a line is equal to (A) Fore bearing ± 90° (B) Fore bearing ± 180° (C) Fore bearing ± 360° (D) Fore bearing ± 270°

Last Answer : (B) Fore bearing ± 180°

An angle of deflection right, may be directly obtained by setting the instrument to read (A) Zero on back station (B) 180° on back station (C) 90° (D) 270° on back station

Description : An angle of deflection right, may be directly obtained by setting the instrument to read (A) Zero on back station (B) 180° on back station (C) 90° (D) 270° on back station

Last Answer : (A) Zero on back station

In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Description : In an amplifier if conductor during the cycle is from 0 to 90° and again from 180° to 270°, the amplifier will be termed as A) Class A B) Class B C) Class C D) Class AB.

Last Answer : B) Class B

ABCD is a regular parallelogram plot of land whose angle BAD is 60°. If the bearing of the line AB is 30°, the bearing of CD, is (A) 90° (B) 120° (C) 210° (D) 270°

Description : ABCD is a regular parallelogram plot of land whose angle BAD is 60°. If the bearing of the line AB is 30°, the bearing of CD, is (A) 90° (B) 120° (C) 210° (D) 270°

Last Answer : (C) 210°

Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Description : Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Last Answer : • Steam turbine

The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Description : In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Last Answer : (D) 360°

The H–C–H bond angle in ethylene is (a) 60° (b) 120° (c) 90° (d) 180°

Description : The H–C–H bond angle in ethylene is (a) 60° (b) 120° (c) 90° (d) 180°

Last Answer : 120°

A -________ incorporates a firebox or furnace in order to burn the fuel and _________ heat. a. Boiler, generate b. Heat, boiler c. Steam, pressure d. None

Description : A -________ incorporates a firebox or furnace in order to burn the fuel and _________ heat. a. Boiler, generate b. Heat, boiler c. Steam, pressure d. None

Last Answer : a. Boiler, generate

What is the value of included angle of a triangular notch for maximum discharge? (A) 30° (B) 60° (C) 90° (D) 120°

Description : What is the value of included angle of a triangular notch for maximum discharge? (A) 30° (B) 60° (C) 90° (D) 120°

Last Answer : (C) 90°

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Description : Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Last Answer : • Boiler

Why single boiler unit per turbine is equipped commonly? • For better turbine control • To reduce the cost • For overcoming losses of power • To improve the efficiency

Description : Why single boiler unit per turbine is equipped commonly? • For better turbine control • To reduce the cost • For overcoming losses of power • To improve the efficiency

Last Answer : • For better turbine control

The vector representing acceleration on a vector diagram for a harmonic motion A) Lags the displacement vector by 90° B) Lags the displacement vector by 180° C) Leads the displacement vector by 90° D) Leads the displacement vector by 180°

Description : The vector representing acceleration on a vector diagram for a harmonic motion A) Lags the displacement vector by 90° B) Lags the displacement vector by 180° C) Leads the displacement vector by 90° D) Leads the displacement vector by 180°

Last Answer : C) Leads the displacement vector by 90°

The velocity vector in a vector diagram for a harmonic motion A) Lags the displacement vector by 180° B) Leads the displacement vector by 90° C) Lags the displacement vector by 90° D) Leads the displacement vector by 180°

Description : The velocity vector in a vector diagram for a harmonic motion A) Lags the displacement vector by 180° B) Leads the displacement vector by 90° C) Lags the displacement vector by 90° D) Leads the displacement vector by 180°

Last Answer : B) Leads the displacement vector by 90°

In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°

Description : In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°

Last Answer : ANSWER : B

In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Description : In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Last Answer : (C) Less than 180°

The sum of the three interior angles of a triangle, the vertices of which lie on the surface of the earth, covering a vast area of several hundreds of sq kms, is : (a) Less than 180° (b) Equal to 180° (c) More than 180° but not less than 270° (d) More than 180° but not more than 225°

Description : The sum of the three interior angles of a triangle, the vertices of which lie on the surface of the earth, covering a vast area of several hundreds of sq kms, is : (a) Less than 180° (b) Equal to 180° (c) More than 180° but not less than 270° (d) More than 180° but not more than 225°

Last Answer : (d) More than 180° but not more than 225°

What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Description : What is the main disadvantage of Lamont boiler ? a. Less flexible in design b. Low heat transfer rate c. Formation of bubbles d. Low steam generation capacity

Last Answer : c. Formation of bubbles

Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Description : Where is water steam separator drum located in Lamont boiler ? a. Inside of the boiler b. Right above the furnace c. Before the feed water pump d. Outside the boiler

Last Answer : d. Outside the boiler

What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Description : What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Last Answer : a. Saturated steam

Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Description : Through what is feed water from hot-well is passed through, before entering steam and water drum in Lamont boiler? a. Evaporator tubes b. Economizer c. Distributor header d. Circulating pump

Last Answer : b. Economizer

The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Description : The propulsion of water into steam drum by extremely rapid, almost explosive boiling of water at the heating surface is called ___________ a) Foaming b) Priming c) Corrosion d) Caustic embrittlement

Last Answer : b) Priming

In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Description : In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Last Answer : (D) 0.067 bar

The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Description : The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Last Answer : (B) Less than

A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Description : A safety valve usually employed with stationary boilers is (A) Lever safety valve (B) Dead weight safety valve (C) High steam and low water safety valve (D) All of these

Last Answer : (D) All of these

If steam is pressurized _____ • It occupies more space • It occupies less space • Both are correct • None of the above

Description : If steam is pressurized _____ • It occupies more space • It occupies less space • Both are correct • None of the above

Last Answer : • It occupies less space

When the bubbles of steam are produced? • Once the water reaches saturation temperature • Once the water starts evaporating • Once the temperature decreases • None of the above

Description : When the bubbles of steam are produced? • Once the water reaches saturation temperature • Once the water starts evaporating • Once the temperature decreases • None of the above

Last Answer : • Once the water reaches saturation temperature

Find the wrong statement. • Boiler is used to produce electricity in the energy business. • Boiler is used to produce steam for generating electricity. • Boiler can pressurize the water and can also evaporate it. All are wrong.

Description : Find the wrong statement. • Boiler is used to produce electricity in the energy business. • Boiler is used to produce steam for generating electricity. • Boiler can pressurize the water and can also evaporate it. All are wrong.

Last Answer : • Boiler can pressurize the water and can also evaporate it.

A boiler or steam generator is a device used to create steam by applying heat energy to _____. • Water • Petrol • Oil • All of the above

Description : A boiler or steam generator is a device used to create steam by applying heat energy to _____. • Water • Petrol • Oil • All of the above

Last Answer : • Water

A steam and condensate system represents a _____ loop. • Discontinuous • Continuous • None of the above • All of the above

Description : A steam and condensate system represents a _____ loop. • Discontinuous • Continuous • None of the above • All of the above

Last Answer : • Continuous

……… is excellent carrier of heat a) Water b) steam c) solid d) None of above

Description : ……… is excellent carrier of heat a) Water b) steam c) solid d) None of above

Last Answer : b) steam

Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Description : Direct relation between…….. &………of saturated steam, the amount of energy input to process easy to control. a) volume, pressure b) volume, temperature c) temperature, pressure d) None of above

Last Answer : c) temperature, pressure

when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Description : when steam is condensate volume is drastically……. a) reduces b) increase c) both a) & b) d) None of above

Last Answer : a) reduces

Rankine cycle efficiency in a good steam power station may be in the range between........ a.15% - 20% b.35% - 40% c.50% - 60% d.90% - 95%

Description : Rankine cycle efficiency in a good steam power station may be in the range between........ a.15% - 20% b.35% - 40% c.50% - 60% d.90% - 95%

Last Answer : b.35% - 40%

What kind of energy output is obtained from a ‘Steam Power Plant’? a. Heat energy b. Sound energy c. Electricity d. Thermal energy

Description : What kind of energy output is obtained from a ‘Steam Power Plant’? a. Heat energy b. Sound energy c. Electricity d. Thermal energy

Last Answer : c. Electricity

A device known as a _______ is used to release condensate from the pipework whilst preventing the steam from escaping from the system. a. Steam traps b. Steam pipes c. Boiler nose d. Release valve

Description : A device known as a _______ is used to release condensate from the pipework whilst preventing the steam from escaping from the system. a. Steam traps b. Steam pipes c. Boiler nose d. Release valve

Last Answer : a. Steam traps

What increase as steam pressure increase inside a boiler • Force • Density • Rate of steam conversion • Viscosity

Description : What increase as steam pressure increase inside a boiler • Force • Density • Rate of steam conversion • Viscosity

Last Answer : • Density

What is the temperature at which the steam boiler are capable to withstand • 200°C • 280°C • 540°C • 358°C

Description : What is the temperature at which the steam boiler are capable to withstand • 200°C • 280°C • 540°C • 358°C

Last Answer : • 540°C

What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Description : What is the function of boiler? • To burn the fuel in a confined closed system With the supply of air • To generate steam in varying pressure • To generate steam at constant pressure • To produce flue gases by burning fuel at a given pressure

Last Answer : • To generate steam at constant pressure

Steam Properties and Qualities: • they are capable of dividing and renewing themselves for long periods • they are unspecialized • they can give rise to specialized cell types. • All of above

Description : Steam Properties and Qualities: • they are capable of dividing and renewing themselves for long periods • they are unspecialized • they can give rise to specialized cell types. • All of above

Last Answer : • All of above

Industrial boilers are closed vessels that use a fuel source or electricity to generate ________for industrial purposes. • Fuel Food • Steam

Description : Industrial boilers are closed vessels that use a fuel source or electricity to generate ________for industrial purposes. • Fuel Food • Steam

Last Answer : • Steam

Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Description : Steam Boilers is used in _________industries • Heating Requirement for Facility. • Steam for Batching. • Steam for Processing. • All of the above

Last Answer : • All of the above

The generated heat is transferred to water to make ______ the process of boiling. • Steam • Boiler • Both • None

Description : The generated heat is transferred to water to make ______ the process of boiling. • Steam • Boiler • Both • None

Last Answer : • Steam