The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

The blades of a centrifugal impeller are said to be curved forward, if
the __________ of the motion of impeller blades.
(A) Inlet tip of a blade curves in a direction opposite to that
(B) Outlet tip of a blade curves in a direction opposite to that
(C) Inlet tip of a blade is towards the direction
(D) Outlet tip of a blade is towards the direction
by

1 Answer

Answer :

(D) Outlet tip of a blade is towards the direction
by

Related questions

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Description : In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Last Answer : ANSWER : D

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Description : Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Last Answer : ANSWER : C

A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Description : A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°

Last Answer : (B) 90°

Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Description : Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Last Answer : (B) Backward curved

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

6. In a forward feed multiple effect, the pressure build up will be (A) Least at the inlet of the first effect (B) Least at the outlet of the last effect (C) Highest at the inlet of the last effect (D) Highest at the outlet of the last effect

Description : 6. In a forward feed multiple effect, the pressure build up will be (A) Least at the inlet of the first effect (B) Least at the outlet of the last effect (C) Highest at the inlet of the last effect (D) Highest at the outlet of the last effect

Last Answer : (B) Least at the outlet of the last effect

For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Description : For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Last Answer : A L-shaped

Railway tracks are banked on curves so that (a) Necessary centrifugal force may be obtained from the horizontal component of the weight of the train (b) Frictional force can be avoided between the tracks and wheels (c) Necessary centripetal force may be obtained from the horizontal component of the weight of the train (d) The train may not fly off in the opposite direction

Description : Railway tracks are banked on curves so that (a) Necessary centrifugal force may be obtained from the horizontal component of the weight of the train (b) Frictional force can be avoided between the tracks ... of the weight of the train (d) The train may not fly off in the opposite direction

Last Answer : Ans:(c)

Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Description : Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Last Answer : (D) Non uniform direction of velocities at inlet & outlet sections

For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing guide vane angle at inlet as 90o c) Providing runner vane angle at exit as 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4

Last Answer : (B) 12.4

Noise produced by cooling fans (employed in air cooled heat exchangers or cooling tower) is mainly caused due to the turbulence created by blade passage through air. It can be reduced by use of a slower fan (A) With greater number of blades (B) Of increased diameter (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Noise produced by cooling fans (employed in air cooled heat exchangers or cooling tower) is mainly caused due to the turbulence created by blade passage through air. It can be reduced by use of a slower fan (A) With greater ... (B) Of increased diameter (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Description : A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Last Answer : (D) Temperature of the solid

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

The 'E' curve for a non-ideal reactor defines the fraction of fluid having age between t and t + dt (A) At the inlet (B) At the outlet (C) In the reactor (D) Averaged over the inlet and outlet

Description : The 'E' curve for a non-ideal reactor defines the fraction of fluid having age between t and t + dt (A) At the inlet (B) At the outlet (C) In the reactor (D) Averaged over the inlet and outlet

Last Answer : (B) At the outlet

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Last Answer : (C) Less than liquid vapor pressure

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller(B) Helical screw(C) Flat blade turbine(D) Curved blade turbine

Description : Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller (B) Helical screw (C) Flat blade turbine (D) Curved blade turbine

Last Answer : (B) Helical screw

Following is not type of blades ? a) ‗L‘ type blade. c) Twisted blade b) ‗M‘ type blade. d) Straight blade

Description : Following is not type of blades ? a) ‗L‘ type blade. c) Twisted blade b) ‗M‘ type blade. d) Straight blade

Last Answer : M‘ type blade.

The following types of blades are used with the rotor in rotary tiller a. ‗L‘ type blade c) both A & B b. Twisted blade d) chisel plough

Description : The following types of blades are used with the rotor in rotary tiller a. ‗L‘ type blade c) both A & B b. Twisted blade d) chisel plough

Last Answer :  both A & B

harrow which consist of one or more blades attached to the beam Or frame, used for shallow working of the soil. A Spike tooth harrow B Acme harrow C Spring tooth harrow D Blade harrow

Description : harrow which consist of one or more blades attached to the beam Or frame, used for shallow working of the soil. A Spike tooth harrow B Acme harrow C Spring tooth harrow D Blade harrow

Last Answer : Blade harrow

The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Description : The isentropic enthalpy drop in moving blade is two-third of the isentropic enthalpy drop in fixed blades of a turbine. The degree of reaction will be (A) 0.4 (B) 0.56 (C) 0.67 (D) 1.67

Last Answer : (A) 0.4

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

What is the purpose of a paring knife with a blade that curves in?

Description : What is the purpose of a paring knife with a blade that curves in?

Last Answer : This type of blade is best for fruit and vegetable carving and peeling in your hand. Imagine peeling an apple while holding the apple in your less dominant hand and the knife in your dominant hand. Now imagine peeling the apple toward yourself. That “birds beak curve” helps make the job easier.

When a running car stops suddenly, the passengers tends to lean forward because of: (1) centrifugal force (2) inertia of rest (3) inertia of motion (4) gravitational force

Description : When a running car stops suddenly, the passengers tends to lean forward because of: (1) centrifugal force (2) inertia of rest (3) inertia of motion (4) gravitational force

Last Answer : (3) inertia of motion Explanation: When a running car stops suddenly, the passengers tend to lean forward due to inertia of motion. Inertia is that property of a body due to which it resists a change in its state of rest or of uniform motion.

When a running car stops suddenly, the passengers tends to lean forward because of: (1) centrifugal force (2) inertia of rest (3) inertia of motion (4) gravitational force

Description : When a running car stops suddenly, the passengers tends to lean forward because of: (1) centrifugal force (2) inertia of rest (3) inertia of motion (4) gravitational force

Last Answer : inertia of motion

Why is an electrical outlet called an outlet when you plug things into it? Shouldn't it be called an inlet?

Description : Why is an electrical outlet called an outlet when you plug things into it? Shouldn't it be called an inlet?

Last Answer : Current flow out from the wall socket when you plug a cord into it. If you want this to be called an inlet and not an outlet, then it would need to be reversed. When you plugged the cord ... flow is by a conductor such as your plug that trips the circuit and allows the electricity to flow freely.

A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours respectively, and an outlet C which can empty the tank in 9 hour

Description : A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours respectively, and an outlet C which can empty the tank in 9 hour

Last Answer : A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours ... time taken right from the start to fill the tank.

Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept 5 to 7.5 cm below the inlet invert level C. The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Description : Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept ... . The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Last Answer : ANS: D