In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is
by

1 Answer

Answer :

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is 32 Kbits/sec
by
edited

Related questions

Choosing a discrete value that is near but not exactly at the analog signal level leads to a) PCM error b) Quantization error c) PAM error d) Sampling error

Description : Choosing a discrete value that is near but not exactly at the analog signal level leads to a) PCM error b) Quantization error c) PAM error d) Sampling error

Last Answer : b) Quantization error

In PCM encoding, quantization level varies as a function of ________ a) Frequency b) Amplitude c) Square of frequency d) Square of amplitude

Description : In PCM encoding, quantization level varies as a function of ________ a) Frequency b) Amplitude c) Square of frequency d) Square of amplitude

Last Answer : b) Amplitude

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

The signals which are obtained by encoding each quantized signal into a digital word is called as a) PAM signal b) PCM signal c) FM signal d) Sampling and quantization

Description : The signals which are obtained by encoding each quantized signal into a digital word is called as a) PAM signal b) PCM signal c) FM signal d) Sampling and quantization

Last Answer : b) PCM signal

What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

In PCM system, if we increase the quantization levels from 2 to 8, the relative bandwidth requirements will: ...

Description : In PCM system, if we increase the quantization levels from 2 to 8, the relative bandwidth requirements will:  (1) Be doubled (2) Remain same (3) Be tripled (4) Becomes eight times

Last Answer : In PCM system, if we increase the quantization levels from 2 to 8, the relative bandwidth requirements will: Be tripled.

In a PCM system of telemetry, the quantization noise depends on:

Description : In a PCM system of telemetry, the quantization noise depends on:  (1) The sampling rate and quantization level (2) The sampling rate only (3) The number of quantization level (4) Information provided is not sufficient

Last Answer : In a PCM system of telemetry, the quantization noise depends on: The number of quantization level.

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz.

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

The first step in PCM is ________. A) quantization B) modulation C) sampling D) none of the above

Description : The first step in PCM is ________. A) quantization B) modulation C) sampling D) none of the above

Last Answer : sampling

The use of non-uniform quantization leads to:

Description : The use of non-uniform quantization leads to: (1) Reduction in transmission bandwidth. (2) Increase in maximum SNR. (3) Increase in SNR for signal levels. (4) Simplification of quantization process. 

Last Answer : The use of non-uniform quantization leads to:  Increase in SNR for signal levels.

The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Description : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Last Answer : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is 32953 bits/second

The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Last Answer : D. 30 to 53 kHz

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

Given an AM radio signal with abandwidth of10 KHzand the highest-frequency component at 705 KHz, what is the frequency of the carrier signal? A) 700 KHz B) 705 KHz C) 710 KHz D) Cannot bedetermined from giveninformation

Description : Given an AM radio signal with abandwidth of10 KHzand the highest-frequency component at 705 KHz, what is the frequency of the carrier signal? A) 700 KHz B) 705 KHz C) 710 KHz D) Cannot bedetermined from giveninformation

Last Answer : 700 KHz

If the bandwidth of a signal is 5 KHz and thelowest frequency is 52 KHz, what is the highest frequency? A) 5 KHz B) 10 KHz C) 47 KHz D) 57 KHz

Description : If the bandwidth of a signal is 5 KHz and thelowest frequency is 52 KHz, what is the highest frequency? A) 5 KHz B) 10 KHz C) 47 KHz D) 57 KHz

Last Answer : 57 KHz

When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Description : When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Last Answer : 45 kHz.

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ.

Description : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

Last Answer : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is 5 KHz

The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased...

Description : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ? (a) -3 dB (b) -5 dB (c) -7 dB (d) -2 dB

Last Answer : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?  -3 dB 

The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -

Description : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -  a) 2 b) 5 c) 3 d) 4

Last Answer : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: - 5

The signal is extended from 96KHz to 100KHz, so the minimum sampling frequency required is...

Description : The signal is extended from 96KHz to 100KHz, so the minimum sampling frequency required is  (a) 8KHz (b) 200KHz (c) 4KHz (d) 100KHz

Last Answer : 200KHZ

If a frequency of 16.8 kHz were measured at the output of 'FF-C' of the circuit shown in the illustration, the clock frequency would be _____________. EL-0087 A. 8.4 kHz B. 50.4 kHz C. 134.4 kHz D. 1680.0 kHz

Description : If a frequency of 16.8 kHz were measured at the output of 'FF-C' of the circuit shown in the illustration, the clock frequency would be _____________. EL-0087 A. 8.4 kHz B. 50.4 kHz C. 134.4 kHz D. 1680.0 kHz

Last Answer : Answer: C

If the clock frequency to the circuit shown in the illustration were 2 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 250 Hz B. 666 Hz C. 6 kHz D. 16 kHz

Description : If the clock frequency to the circuit shown in the illustration were 2 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 250 Hz B. 666 Hz C. 6 kHz D. 16 kHz

Last Answer : Answer: A

Human ear is most sensitive to noise in the following frequency ranges: (A) 1-2 KHz (B) 100-500 Hz (C) 10-12 KHz (D) 13-16 KHz

Description : Human ear is most sensitive to noise in the following frequency ranges: (A) 1-2 KHz (B) 100-500 Hz (C) 10-12 KHz (D) 13-16 KHz

Last Answer : (A) 1-2 KHz

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

Companding helps in reducing __________ with respect to signal: (A) Interference (B) Signal overloading (C) Non linearity (D) Quantization noise

Description : Companding helps in reducing __________ with respect to signal: (A) Interference (B) Signal overloading (C) Non linearity (D) Quantization noise

Last Answer : (D) Quantization noise

The process of dividing an analog signal into a string of discrete outputs, each of constant amplitude, is called: (A) Strobing (B) Amplification (C) Conditioning (D) Quantization

Description : The process of dividing an analog signal into a string of discrete outputs, each of constant amplitude, is called: (A) Strobing (B) Amplification (C) Conditioning (D) Quantization

Last Answer : (D) Quantization

For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Description : For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Last Answer : C. 20 kHz

In commercial FM broadcasting, the maximum frequency deviation is normally

Description : In commercial FM broadcasting, the maximum frequency deviation is normally   (A) 5 KHz (B) 15 KHz (C) 75 KHz (D) 200 KHz

Last Answer : In commercial FM broadcasting, the maximum frequency deviation is normally 75 KHz

The maximum Usable Frequency is dependent on

Last Answer : The maximum Usable Frequency is dependent on the electron density of the ionospheric layer.

Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Description : Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Last Answer : B. Sampling, quantizing, and coding

The most common technique to change an analog signal to digitaldata is called __________. A) PAL B) PCM C) sampling D) none of the abov

Description : The most common technique to change an analog signal to digitaldata is called __________. A) PAL B) PCM C) sampling D) none of the abov

Last Answer : PCM

Used for transmission of PCM encoded time – division multiplexed digital signal.

Description : Used for transmission of PCM encoded time – division multiplexed digital signal.

Last Answer : T carriers

ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.

A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Description : A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Last Answer : 6 Kbps

If a carrier wave of 1000 kHz is used to carry the signal, the length of transmitting antenna will be equal to _______. (1) 300 m (2) 30 m (3) 3 m (4) 0.3 m

Description : If a carrier wave of 1000 kHz is used to carry the signal, the length of transmitting antenna will be equal to _______. (1) 300 m (2) 30 m (3) 3 m (4) 0.3 m

Last Answer : (1) 300 m Explanation: h = 3 × 108/106 = 300 m

What is the spectrum of stereophonic FM signal? A. 19 to 38 kHz B. 30 to 53 kHz C. 59.5 to 74.5 kHz D. 88 to 108 MHz

Description : What is the spectrum of stereophonic FM signal? A. 19 to 38 kHz B. 30 to 53 kHz C. 59.5 to 74.5 kHz D. 88 to 108 MHz

Last Answer : B. 30 to 53 kHz

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

What is the bandwidth ofa signal that ranges from 1 MHz to4 MHz? A) 4 MHz B) 1 KHz C) 3 MHz D) none of the above

Description : What is the bandwidth ofa signal that ranges from 1 MHz to4 MHz? A) 4 MHz B) 1 KHz C) 3 MHz D) none of the above

Last Answer : 3 MHz

A periodic signal completes onecycle in 0.001 s. What is thefrequency? A) 1 Hz B) 100 Hz C) 1 KHz D) 1 MHz

Description : A periodic signal completes onecycle in 0.001 s. What is thefrequency? A) 1 Hz B) 100 Hz C) 1 KHz D) 1 MHz

Last Answer : 1 KHz

A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Description : A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Last Answer : The recorder has 2% third-harmonic distortion of a 100-kHz signal at 60 ips.

What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Description : What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Last Answer : An unbalance in the metering bridge.

In a microwave test bench, why is the microwave signal amplitude modulated at 1 kHz?

Description : In a microwave test bench, why is the microwave signal amplitude modulated at 1 kHz?  (1) To increase the sensitivity of measurement (2) To transmit the signal to a far-off place (3) To study amplitude modulation (4) Because crystal detector fails at microwave frequencies

Last Answer : In a microwave test bench, why is the microwave signal amplitude modulated at 1 kHz?  Because crystal detector fails at microwave frequencies

State the need of signal conditioning and signal processing .List applications of instrumentation amplifier.

Description : State the need of signal conditioning and signal processing .List applications of instrumentation amplifier.

Last Answer : * In an instrumentation system, a transducer is used for sensing various parameters. The output of transducer is an electrical signal proportional to the physical quantity sensed such as pressure, ... monitoring and control 5) Light intensity meter 6) Measurement of flow and thermal conductivity

Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle?

Description : Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle? (1) Thermal noise (2) Shot noise (3) Environmental noise (4) Background Noise

Last Answer : Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle? (1) Thermal noise (2) Shot noise (3) Environmental noise (4) Background Noise

In communication systems, the modulating signal is also called

Last Answer : In communication systems, the modulating signal is also called base band signal.

What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Last Answer : B. 320 kHz