If the bandwidth of a signal is 5 KHz and thelowest frequency is 52 KHz, what is the highest frequency?
A)
5 KHz
B)
10 KHz
C)
47 KHz
D)
57 KHz

1 Answer

Answer :

57 KHz

Related questions

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

Description : What is the bandwidth ofa signal that ranges from 1 MHz to4 MHz? A) 4 MHz B) 1 KHz C) 3 MHz D) none of the above

Last Answer : 3 MHz

Description : Given an AM radio signal with abandwidth of10 KHzand the highest-frequency component at 705 KHz, what is the frequency of the carrier signal? A) 700 KHz B) 705 KHz C) 710 KHz D) Cannot bedetermined from giveninformation

Last Answer : 700 KHz

Description : The _____of a composite signal is the difference between the highest and the lowest frequencies contained in that signal. A) frequency B) period C) bandwidth D) amplitude

Last Answer : frequency

Description : If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Last Answer : 1200 samples/s

Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Last Answer : B. 320 kHz

Description : An FDM hierarchy which is formed by frequency – division multiplexing five groups containing 12 channels each for a combined bandwidth of 240 kHz

Last Answer : Supergroup

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

Description : A periodic signal completes onecycle in 0.001 s. What is thefrequency? A) 1 Hz B) 100 Hz C) 1 KHz D) 1 MHz

Last Answer : 1 KHz

Description : What frequency range is used for FM radio transmission? A. Very Low Frequency : 3 kHz to 30. kHz B. Low Frequency :30 kHz to 300 kHz C. High Frequency :3 MHz to 30 MHz D. Very High Frequency : 30 MHz to 300 MHz E. None of the above

Last Answer : Very High Frequency : 30 MHz to 300 MHz

Description : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

Last Answer : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is 5 KHz

Description : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -  a) 2 b) 5 c) 3 d) 4

Last Answer : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: - 5

Description : A(n)_________ signal is a composite analogsignal with an infinite bandwidth. A) digital B) analog C) either (a)or (b) D) neither (a) nor (b

Last Answer : digital

Description : The Nyquist theorem specifies the minimum samplingrate to be_______. A) equal to the lowest frequency of asignal B) equal to the highest frequency ofa signal C) twice thebandwidth of a signal D) twice thehighest frequencyof a signal

Last Answer : twice thehighest frequencyof a signal

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Last Answer : D. 30 to 53 kHz

Description : Find the mean of the data 7, 8, 10, 13, 17, 23, 30, 38, 47, and 57.

Last Answer : Find the mean of the data 7, 8, 10, 13, 17, 23, 30, 38, 47, and 57.

Description : From the steam table, determine the average constant pressure specific heat (c) of steam at 10 kPa and45.8 ˚C  A.1.79 kJ/ kg-˚C  B.10.28 kJ/ kg-˚C  C.30.57 kJ/ kg-˚C  D. 100.1 kJ/ kg-˚C Formula: h = c T ∆ ∆ From the steam table At 47.7 ˚C h= 2588.1 kJ/ kg At 43.8 ˚C h= 2581.1 kJ/ kg

Last Answer : 1.79 kJ/ kg-˚C

Description : In________, the available bandwidth is divided into frequency bands. A) FDMA B) TDMA C) CDMA D) none of the above

Last Answer : TDMA

Description : _________ utilization is the useof availablebandwidthto achieve specificgoals. A) Frequency B) Bandwidth C) Amplitude D) None of the abov

Last Answer : Bandwidth

Description : The _________ product defines the number ofbits that can fill the link. A) bandwidth-period B) frequency-amplitude C) bandwidth-delay D) delay-amplitude

Last Answer : bandwidth-delay

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

Description : When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Last Answer : 45 kHz.

Description : In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

Last Answer : In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is 32 Kbits/sec

Description : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ? (a) -3 dB (b) -5 dB (c) -7 dB (d) -2 dB

Last Answer : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?  -3 dB 

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

Description : The bandwidth requirement of a telephone channel is (A) 3 KHz (B) 15 KHz (C) 5 KHz (D) 25 KHz

Last Answer : (A) 3 KHz

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Last Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Description : How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Last Answer : B. 200 kHz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

Description : What category of digital tape recorder is used to record special signals with a bandwidth of less than 500 kHz?

Last Answer : Instrumentation digital tape recorders.

Description : A piezo-electric type pressure sensor has a sensitivity of 1 mV/kPa and a bandwidth of 300 Hz to 300 kHz. For a constant (dc) pressure of 100 kPa, the steady state output of the sensor in millivolt is (A) 0 (B) 2 (C) 4 (D) 6

Last Answer : A piezo-electric type pressure sensor has a sensitivity of 1 mV/kPa and a bandwidth of 300 Hz to 300 kHz. For a constant (dc) pressure of 100 kPa, the steady state output of the sensor in millivolt is 0

Description : What decimal is greater than 47 and less than 57?

Last Answer : 49 is one possible answer.

Description : Find the missing number in the series: 60 59 57 54 50 _________. A. 45 B. 47 C. 44 D. 43

Last Answer : ANSWER: A

Description : Find the missing number in the series: 60 59 57 54 50 _________. A. 45 B. 47 C. 44 D. 43

Last Answer : ANSWER: A

Description : If V = 2x 2 y – 5z, find its electric field at point (-4,3,6) a) 47.905 b) 57.905 c) 67.905 d) 77.905

Last Answer : b) 57.905

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

Description : The percentage share of electrical power from solar energy in the total electric power generation from all renewable energy sources sought to be achieved by Indian government by the year 2022, is (A) ~ 57.1% (B) ~ 65.5% (C) ~ 47.5% (D) ~ 75% 

Last Answer : Answer: A

Description : The average of 7 consecutive odd numbers is 41. Find the largest of these numbers A) 40 B) 57 C) 47 D) 43

Last Answer : C) Let the numbers be x , x+2,x+4,x+6, x+8, x+10 and x+12 Then x+x+2+x+4+x+6+x+8+x+10+x+12/7 7x+42=287 7x=245 X=35 Largest number = x+12 = 35+12 =47

Description : An ideal air standard Otto cycle has a compression ratio of 8.5. If the ratio of the specific heats is 1.4, then what is thermal efficiency (in percentage) of the Otto cycle? a. 57.5% b. 45.7% c. 52.5% d. 95%

Last Answer : ANSWER a. 57.5%

Description : It indicates what signal frequencies can be propagated through a given distance of fiber cable. ∙ A. Bandwidth Distance Product ∙ B. Pulse width dispersion ∙ C. Rise time ∙ D. Cutoff frequency

Last Answer : A. Bandwidth Distance Product

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

Description : 47 out of 52 of my classmates survive to age 74. What are the odds?

Last Answer : answer:Welcome to Fluther. Someone will be along shortly with the stats on that.

Description : What is the playing time of the full version of the Indian National Anthem? (1) (1) 47 seconds (2) (2) 50 seconds (3) 52 seconds (4) 60 seconds

Last Answer : (3) 52 seconds Explanation: The composition consisting of the words and music of the first stanza of the late poet Rabindra Nath Tagore's song known as "Jana Gana Mana" is the National Anthem ... Anthem is also played on certain occasions. Playing time of the short version is about 20 seconds.

Description : What is the mean median and mode of 52 53 54 55 55 56 57 57 57 59 60?

Last Answer : Find the mode of the following data: 55,55, 56, 52, 57, 55, 58, 59, 60, 60

Description : The playing time (In seconds) of the full version of Indian National Anthem is- (1) 60 (2) 52 (3) 55 (4) 57

Last Answer : (2) 52 Explanation: A formal rendition of the national anthem takes fifty-two seconds. A shortened version consisting of the first and last lines (and taking about 20 seconds to play) is also staged occasionally.

Description : When was the First Gerneral Election to the Lok Sabha held? (1) 1950 - 51 (2) 1951 - 52 (3) 1952 - 53 (4) 1956 - 57

Last Answer : (2) 1951 – 52 Explanation: General elections to the first Lok Sabha since independence was held in India were held between 25 October, 1951 and 21 February, 1952. The Indian National Congress (INC) stormed into power with 364 of the 489 seat.

Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less than O's lockers ... could be a) 52 or 53 only b) 53 or 54 only c) 54 or 55 only d) 53 or 55 only

Last Answer : c) 54 or 55 only

Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less ... , then which locker number is not allocated? a) locker 52 b) locker 53 c) locker 54 d)locker 56

Last Answer : a) locker 52

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2