Description : . Fan nozzle forms narrow. spray pattern. a. large c. Straight. d. None of above
Last Answer : Ans- b. elliptical.
Description : is the types of nozzle used in sprayers a) Hollow cone type of nozzle b) Solid cone type nozzle c) Fan type nozzle d) All of the above
Last Answer : All of the above
Description : Spray Angle for fan nozzles and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150
Last Answer : c) 60-95
Description : The nozzle used for chemical spraying of weedicides (a) hollow cone nozzle (b) solid cone nozzle (c) flat fan nozzle (d) flooding nozzle
Last Answer : (c) flat fan nozzle
Description : Spary angle for fan nozzle and hollow cone nozzle a) 40-50 b) 50-60 c) 60-95 d) 100-150
Description : Foam spraying requires special type of nozzle A. Flat fan nozzle B. Flooding nozzle C. Hollow cone nozzle D. Air aspiring nozzle
Last Answer : D. Air aspiring nozzle
Description : A flat fan nozzle is suitable for a) Foliage spray b) Insect control c) Spot spray d) Herbicide spray
Last Answer : ans d
Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.
Last Answer : a. Impart rotational motion to the liquid passing through it.
Description : Hollow cone nozzles employed on boom type of sprayers have spray angle between : A .30-60° B.40-60° C.60-95° D.100-150°
Last Answer : C.60-95°
Description : Hallow cone nozzle – liquid is fed into whirl chamber through entry or through a fixed spiral passage to give rotation motion. a. Axial b. Radial c. tangential. d. None of above
Last Answer : Ans- c. tangential.
Description : It is the part of cone nozzle which imparts rotation to the liquid. b. Cone plate c. Round plate d. None of above
Last Answer : Ans- a. Swirl plate
Description : Name of instrument used for testing of spray nozzle a) Patternator b) Aerometer c) Galvanometer d) Piezometer Ans. a
Last Answer : ans a
Description : Basic components of sprayer is a) Nozzle body b) Spray boom c) Nozzle cap d) All of the above
Description : Component to remove suspended matter large than a predetermined size from fluid. a. Relief valve. c. Filter b. Spray gun. d. Nozzle
Last Answer : Filter
Description : Basic components of sprayer. a. Nozzle body b. Nozzle boss c. Filter d. Spray gun e. All of the above
Description : Junior hoe consist of and attached to the framework with hinge arrangement a) Reversible showers, nozzle body b) Reversible shovels, curved tynes c) Reversible shovels, curved tyres d) Pressure regulator, spray lance
Last Answer : Reversible shovels, curved tynes
Description : Fan nozzle mostly used for pressure spraying. b. high c. moderate d. None of above
Last Answer : Ans- b. low
Description : In the natural draft cooling tower_________ is not required a) Fan b) tower c) Nozzle d) none of the above
Last Answer : Fan
Description : In the following geometric primitives. which is not a solid entity of CSG modelling: a.Box b.Cone c.Cylinder d.Circle
Last Answer : d.Circle
Description : How many number of spray nozzle does each module on spray pond cooling system contain? a. 1 b. 2 c. 3 d. 4
Last Answer : d. 4
Description : Flooding nozzle have spray angle a) 100-150 b) 90-100 c) 60-95 d) 30-45
Last Answer : a) 100-150
Description : Nozzle spacing on boom is governed by a.) Type of spray b.) Height of crops c.) Density of crop d.) All of the above
Last Answer : d.) All of the above
Description : A bus stop is barricaded from the remaining part of the road, by using 50 hollow cones made of recycled cardboard. Each cone has a base diameter of 40 cm and height 1 m. -Maths 9th
Last Answer : Given: Radius of cone, r = diameter/2 = 40/2 cm = 20cm = 0.2 m Height of cone, h = 1m Slant height of cone is l, and l2 = (r2+h2) Using given values, l2 = (0.22+12) = (1.04) Or l ... (32.028 12) = Rs.384.336 = Rs.384.34 (approximately) Therefore, the cost of painting all these cones is Rs. 384.34.
Description : Center of gravity of a thin hollow cone lies on the axis at a height of (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base
Last Answer : (B) One-third of the total height above base
Description : Center of gravity of a thin hollow cone lies on the axis at a height of?
Last Answer : Center of gravity of a thin hollow cone lies on the axis at a height of one-third of the total height above base.
Description : What is allotrope ? In what forms of cubic pattern, iron exists ?
Last Answer : Some elements exist in more than one crystalline form. Each form is known as “allotrope”. Iron exists in two forms of cubic pattern, namely body centered cubic (bcc) and face-centered cubic (fee).
Description : ___________ is a satellite that rotates around the earth in a low-altitude elliptical or circular pattern. A. Geosynchronous satellite B. Nonsynchronous satellite C. Prograde satellite D. Retrograde satellite
Last Answer : B. Nonsynchronous satellite
Description : Under what condition a convergent divergent nozzle required ?
Last Answer : When pressure ratio is greater than critical pressure ratio.
Description : Under what circumstances would there be an increase in pressure in a diver¬gent nozzle ?
Last Answer : For subsonic flow at inlet section of a diffuser a lower velocity and higher pressure will exist at the exit section. For supersonic isentropic flow at the inlet section a higher velocity and lower pressure ... if a shock wave occurs in the diffuser then a higher pressure will exist at the exit.
Description : What is the effect of friction on flow of steam through a nozzle ?
Last Answer : To decrease both mass flow rate and wetness of steam.
Description : When maximum discharge is obtained in nozzle ?
Last Answer : At the critical pressure ratio.
Description : In a sprayer overlapping can be increased by increasing a) Nozzle diameter b) Pressure c) Discharge d) Height of nozzle Ans. d
Description : The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above
Last Answer : Wearing Plate
Description : Nozzle diameter of hand atomizer is between ………… to ………… a. 0.7 – 1.5. c. 1.1- 1.5 b. 0.6 – 1.6. d 0.8 to 1.8
Last Answer : 0.6 – 1.6.
Description : Nozzle consists of components a) Washer b) Vortex plate c) Strainer d) All of the above
Description : is the minimum pressure required for operating a nozzle in desirable condition a) 1 kg/cm b) 1.5kg/cm c) 2 kg/cm d) 2.5kg/cm
Last Answer : 1.5kg/cm
Description : Open system usually encloses which of the following devices? A. Compressor B. Turbine C. Nozzle D. All of the above
Description : What is the organizational pattern of how to eat an ice-cream cone by L. Rust Hills?
Last Answer : sequential
Description : What is the organizational pattern of how to eat an ice-cream cone by L. Rust Hills apex?
Description : Which of the following is not one of the channel pattern? (A) Braided (B) Narrow (C) Meandering (D) Straight
Last Answer : (B) Narrow
Description : A square paper is folded and cut as shown below. The paper is then used as a template to spray-paint a white wall with black paint. Which pattern would be created using this template?
Last Answer : B
Description : Will your chocolate easter bunny be hollow or solid
Last Answer : neither.. how bout yours?
Description : A hollow sphere and a solid sphere of the same material and equal radii are heated to the same temperature. In this case, (A) The cooling rate will be the same for the two spheres and hence the ... equal amount of radiation from the surrounding in the beginning (D) Both (B) & (C)
Last Answer : (D) Both (B) & (C)
Description : Solid shaft is costlier than hollow shaft of same weight. a) True b) False
Last Answer : b) False
Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False
Last Answer : a) True
Description : The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight. a) True b) False
Description : Muff coupling is designed as a ......... A. Thick cylinder B. Thin cylinder C. Solid shaft D. Hollow shaft
Last Answer : D. Hollow shaft