Each set of discs that are mounted on a common shaft is called as i. Spool. c) Bearing ii. Gang. d) Gang control

Each set of discs that are mounted on a common shaft is called as i. Spool. c) Bearing ii. Gang. d) Gang control
by

1 Answer

Answer :

Gang
by

Related questions

Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Description : Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Last Answer : Gang

The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Description : The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Last Answer : Spool

The lateral movement of disc on shaft is called as A) Spool. C) Gang B) Bearing D) Gear

Description : The lateral movement of disc on shaft is called as A) Spool. C) Gang B) Bearing D) Gear

Last Answer : Spool

A set of discs are mounted on the i. Gang bolt c) Both a) and b) ii. Arbor bolt. d) Non of the above

Description : A set of discs are mounted on the i. Gang bolt c) Both a) and b) ii. Arbor bolt. d) Non of the above

Last Answer : Both a) and b)

is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Description : is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Last Answer : Bearing

operates gang mechanisms. A) Gang. C) Spool B) Gang bolt D) Gang control lever

Description : operates gang mechanisms. A) Gang. C) Spool B) Gang bolt D) Gang control lever

Last Answer : Gang

The spacing between the discs in the gang bolt ranges cm for lighy duty and cm heavy -duty harrows i. 15-25 and 25-30 c) 40-45 and 45-50 ii. 20-30 and 30-40. d) 15-25 and 32-36

Description : The spacing between the discs in the gang bolt ranges cm for lighy duty and cm heavy -duty harrows i. 15-25 and 25-30 c) 40-45 and 45-50 ii. 20-30 and 30-40. d) 15-25 and 32-36

Last Answer : 15-25 and 25-30

is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Description : is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Last Answer :  Disc harrow

A lever, which operates the gang mechanism of the disk harrow, is called the i. Spanners lever. c) spacer lever ii. Gang control lever. d) Bearing lever

Description : A lever, which operates the gang mechanism of the disk harrow, is called the i. Spanners lever. c) spacer lever ii. Gang control lever. d) Bearing lever

Last Answer : Gang control lever

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

is a circular concave revolving steel plate using for cutting and inverting the soil. a. Gang bolt. c. Disc b. Bearing d. None

Description : is a circular concave revolving steel plate using for cutting and inverting the soil. a. Gang bolt. c. Disc b. Bearing d. None

Last Answer : Bearing 

is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Description : is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Last Answer : Bearing.

A flywheel weighs 400 kg and has a radius of gyration of 30 cm about its axis of rotation. It is mounted on a shaft subjected to a moment of 40 kgm. If the flywheel starts from restits speed after 3 seconds wil be a.10.9 rad/sec b.19.0 rad/sec c.51.2 rad/sec d.3.33 rad/sec e.16.35 rad/sec

Description : A flywheel weighs 400 kg and has a radius of gyration of 30 cm about its axis of rotation. It is mounted on a shaft subjected to a moment of 40 kgm. If the flywheel starts from restits speed after 3 seconds wil be a.10.9 rad/sec b.19.0 rad/sec c.51.2 rad/sec d.3.33 rad/sec e.16.35 rad/sec

Last Answer : d. 3.33 rad/sec

In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Last Answer : ans c

This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Last Answer : Ans-                             c. Dummy

It consists of beats mounted on a shaft which rotates inside a closed casing and concave. a) Dummy type c) Spike-tooth type c) Hummer type d) Axial flow type

Description : It consists of beats mounted on a shaft which rotates inside a closed casing and concave. a) Dummy type c) Spike-tooth type c) Hummer type d) Axial flow type

Last Answer : Dummy type

it is a Cultivator with tines or blades mounted on a power driven horizontal shaft. A. Disc cultivator. C Rotary cultivator B. Tine cultivator. D Trailed type cultivator

Description : it is a Cultivator with tines or blades mounted on a power driven horizontal shaft. A. Disc cultivator. C Rotary cultivator B. Tine cultivator. D Trailed type cultivator

Last Answer : Rotary cultivator

If two discs are attached to one shaft at its both end, then it has_____ number of natural frequencies. A Infinite B One C Two D None of the mentioned

Description : If two discs are attached to one shaft at its both end, then it has_____ number of natural frequencies. A Infinite B One C Two D None of the mentioned

Last Answer : B One

A shaft of diameter d carries two discs at its two ends. The lowest torsional frequency is ω n . If the diameter is doubled, then the lowest torsional frequency becomes A 4ω n B ω n /2 C ω n /4 D 4ω n

Description : A shaft of diameter d carries two discs at its two ends. The lowest torsional frequency is ω n . If the diameter is doubled, then the lowest torsional frequency becomes A 4ω n B ω n /2 C ω n /4 D 4ω n

Last Answer : D 4ω n

A shaft of length l carries two discs at its two ends. The lowest torsional frequency is ω n . If the shaft length is doubled, then the lowest torsional frequency becomes A ω n /2 B ω n /√2 C √2ω n D 2ω n

Description : A shaft of length l carries two discs at its two ends. The lowest torsional frequency is ω n . If the shaft length is doubled, then the lowest torsional frequency becomes A ω n /2 B ω n /√2 C √2ω n D 2ω n

Last Answer : B ω n /√2

The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Description : The type of bearing generally used to support the discs on a standard disc plough is: A. Ball bearing. B. Tapered roller bearing. C. Plain roller bearing. D. Bush bearing.

Last Answer : B. Tapered roller bearing.

Tandem disc Harrow is a disc Harrow comprising of four gangs in which each gang can be angle in… direction. a. Angular c. Parallel b. Opposite. d. Perpendicular

Description : Tandem disc Harrow is a disc Harrow comprising of four gangs in which each gang can be angle in… direction. a. Angular c. Parallel b. Opposite. d. Perpendicular

Last Answer : Opposite

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

There are n rotors mounted on the shaft and when subjected to torsional vibration there will be A. N nodes B. (N-1) nodes C. (N+1) nodesD. Any number of nodes

Description : There are n rotors mounted on the shaft and when subjected to torsional vibration there will be A. N nodes B. (N-1) nodes C. (N+1) nodesD. Any number of nodes

Last Answer : B. (N-1) nodes

Describe with sketch (i) Poppet valve (ii) Spool valve.

Description : Describe with sketch (i) Poppet valve (ii) Spool valve.

Last Answer : A poppet valve (also called mushroom valve) is a valve typically used to control the timing and quantity of gas or vapors flow into an engine. It consists of a hole, usually round or oval, and ... flow from one source to the other. In pneumatic logic a shuttle-valve works as an OR gate.  

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left Side .045 - .047, Bottom .045 - .041 Which of the f A. both the aft and foward bearings should be replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left Side .045 - .047 , Bottom .045 - .041 Which of the fo A. The aft bearing should be realigned or replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Tractor drawn disc harrows have concave discs of size varying from… diameter. a. 55-90cm b. 60-100cm d. None of the above

Description : Tractor drawn disc harrows have concave discs of size varying from… diameter. a. 55-90cm b. 60-100cm d. None of the above

Last Answer : Ans - c. 35-70cm

The spacing between two adjacent discs in Olpad thresher is a) 5 cm b) 10 cm c) 15 cm d) 20 cm

Description : The spacing between two adjacent discs in Olpad thresher is a) 5 cm b) 10 cm c) 15 cm d) 20 cm

Last Answer : 15 cm

plows are rows of concave steel discs that revolve as they are pulled. A. Disk. C) Chisel B. Tined. D) Sub soiling

Description : plows are rows of concave steel discs that revolve as they are pulled. A. Disk. C) Chisel B. Tined. D) Sub soiling .

Last Answer : Disk

Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a

Description : Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a

Last Answer : ans a

The adjustment in MB plough for increasing the depth of operation a) Vertical suction b) Horizontal suction c) Gang angle d) Disc angle Ans. a

Description : The adjustment in MB plough for increasing the depth of operation a) Vertical suction b) Horizontal suction c) Gang angle d) Disc angle Ans. a

Last Answer : ans a

The required spacing between the disc on the gang bolt ranges from 15 to 25 cm for light duty and 25 to 30cm for heavy duty harrows is b. 25 to 35cm c. 25 to 40cm d. None of the above.

Description : The required spacing between the disc on the gang bolt ranges from 15 to 25 cm for light duty and 25 to 30cm for heavy duty harrows is b. 25 to 35cm c. 25 to 40cm d. None of the above.

Last Answer :    <!-- [endif] -->Ans - a. 25 to 30cm

is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Description : is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Last Answer : Sickle mower

The gang angle of disc harrow is adjusted in the range of: a) 0-30 c) 30-60 b) 60-90 d) Above 90

Description : The gang angle of disc harrow is adjusted in the range of: a) 0-30 c) 30-60 b) 60-90 d) Above 90

Last Answer : B

Is It Possible To Mount The Compressor Sideways? Must It Be Mounted With The Cylinder Upright?

Description : Is It Possible To Mount The Compressor Sideways? Must It Be Mounted With The Cylinder Upright?

Last Answer : Yes, you can mount our compressors in any direction or position because they are oil-less. The only position we do not recommend is an upside-down mount, since heat tends to travel upward.

This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Raspbar

A potato digger elevator can be mounted to a tractor with hp. a) 10-15 hp b) 20-25 hp c) 50-70 hp d) None of the above

Description : A potato digger elevator can be mounted to a tractor with hp. a) 10-15 hp b) 20-25 hp c) 50-70 hp d) None of the above

Last Answer : 20-25 hp

In threshers what are mounted on the periphery of the cylinder A) Spike tooth type B) Raspbar type C) Syndicator type D) Wire loob type.

Description : In threshers what are mounted on the periphery of the cylinder A) Spike tooth type B) Raspbar type C) Syndicator type D) Wire loob type.

Last Answer : Spike tooth type

are mounted on the Periphery of a cylinder that rotates inside a closed casing and concave. a) Dummy type c) spike-tooth type b) Hummer type d) Axial flow type

Description : are mounted on the Periphery of a cylinder that rotates inside a closed casing and concave. a) Dummy type c) spike-tooth type b) Hummer type d) Axial flow type

Last Answer : spike-tooth type

The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above

Description : The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above

Last Answer : rear 

is pulled and guided from single hitch point but its weight is not supported by the tractor. A. Trailed type implement C. Semi mounted type implemented B. Mounted type implemented D. Automatic implemented

Description : is pulled and guided from single hitch point but its weight is not supported by the tractor. A. Trailed type implement C. Semi mounted type implemented B. Mounted type implemented D. Automatic implemented

Last Answer : Trailed type implement

An implement that pulled and guided by single hitch point of a tractor is: a) Trailed implement c) Mounted implement b) Semi mounted implements d) All are correct

Description : An implement that pulled and guided by single hitch point of a tractor is: a) Trailed implement c) Mounted implement b) Semi mounted implements d) All are correct

Last Answer : Trailed implement

How do you replace a broken spool pin on a Brother SE-400?

Description : How do you replace a broken spool pin on a Brother SE-400?

Last Answer : This might help. http://www.manualowl.com/m/Brother%20International/SE-400/Manual/255869

No SPOOL HOLDER for my Brothers XL-3100 machine substitution?

Description : No SPOOL HOLDER for my Brothers XL-3100 machine substitution?

Last Answer : answer:Welcome to Fluther! The links below are to a few sites that have replacement parts for that machine. I found several other options in the Google search that I did. If you search ... parts.aspx http://www.mysewingmachineparts.com/brother-xl3100/ http://www.thesewingoutlet.com/brother-xl-3100/

Sewing machine question: the piece that holds the spool of thread on top is missing. What can I use?

Description : Sewing machine question: the piece that holds the spool of thread on top is missing. What can I use?

Last Answer : If you are not in a hurry, most brands of machines have replacement parts and you can get a new spool pin (that is what it is called) for most machines. What brand of machine do you have?

What are the advantages of using logical spool servers? Note: there are 2 correct answered to this question A. You can create more output devices B. You can balance the load across multiple physical spool servers C. You can minimize the load on physical devices D. You can minimize the manual adjustment of output device definitions after the transport

Description : What are the advantages of using logical spool servers? Note: there are 2 correct answered to this question A. You can create more output devices B. You can balance the load across ... on physical devices D. You can minimize the manual adjustment of output device definitions after the transport

Last Answer : B. You can balance the load across multiple physical spool servers C. You can minimize the load on physical devices