Description : It consists of beats mounted on a shaft which rotates inside a closed casing and concave. a) Dummy type c) Spike-tooth type c) Hummer type d) Axial flow type
Last Answer : Dummy type
Description : It consists of spike tooth cylinder, woven- wire mesh concave and upper casing provided with helical concave. a) Dummy type c) Spike-tooth type b) Hummer type d) Axial flow type
Last Answer : Axial flow type
Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above
Last Answer : Ans- c. Dummy
Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Axial flow
Description : Identify the picture. a) Hummer mill type b) Spike-tooth type c) Dummy type d) Axial flow type
Last Answer : Hummer mill type
Description : In threshers what are mounted on the periphery of the cylinder A) Spike tooth type B) Raspbar type C) Syndicator type D) Wire loob type.
Last Answer : Spike tooth type
Description : This type thresher consists of a flywheel with corrugation on its periphery and sides. Rims of flywheel fitted with chopping blades. b. Axial flow c. Dummy d. None of above
Last Answer : Ans- a. Syndicator
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder
Description : The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher
Last Answer : Hammer mill type thresher
Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Raspbar
Description : is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow
Last Answer : Disc harrow
Description : A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above
Last Answer : All of the above
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate
Last Answer : Option D
Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails
Last Answer : ans 3
Description : harrow having curved knives. i. Spring tooth harrow. c) Acme harrow ii. Spikal tooth d) Spike tooth harrow
Last Answer : Acme harrow
Description : harrow which consist of one or more blades attached to the beam Or frame, used for shallow working of the soil. A Spike tooth harrow B Acme harrow C Spring tooth harrow D Blade harrow
Last Answer : Blade harrow
Description : it is a harrow with peg shaped teeth of diamond cross section to a Rectangular frame. A) Spike tooth harrow C Spring tooth harrow B) Acme harrow D Triangular harrow.
Last Answer : Spike tooth harrow
Description : Is It Possible To Mount The Compressor Sideways? Must It Be Mounted With The Cylinder Upright?
Last Answer : Yes, you can mount our compressors in any direction or position because they are oil-less. The only position we do not recommend is an upside-down mount, since heat tends to travel upward.
Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct
Last Answer : All are correct
Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.
Last Answer : All of the above.
Description : The takes place between the cylinder and concave units of the combine. a) Threshing b) Feeding drum c) Straw spreader d) Separating
Last Answer : Threshing
Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted
Last Answer : (a) Yes
Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated
Last Answer : a) Yes
Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these
Last Answer : (A) Open
Description : is also called as knife harrow. a. Spring tooth harrow b. Acme harrow c. Spike tooth harrow d. none of the above
Last Answer : Ans:- b. Acme harrow
Description : Implements commonly used in dry farming areas a). Sweep b). Blade harrow c). Spike tooth harrow d). Both a and b
Last Answer : d). Both a and b
Description : Blind hoeing with bullock/tractor drawn spike-tooth harrow successfully controls weeds in a). Potato b). Sugarcane c). Maize d). Both a and b
Description : Cono weeder consist of conical rollers have on the periphery. a. Helical projection c. Interrupted projection d. None of above
Last Answer : Ans- b. serrated projection
Description : Why axial flow compressor is preferred for gas turbines for aeroplanes ?
Last Answer : Because it has low frontal area.
Description : Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?
Last Answer : Isentropic efficiency of axial flow compressor is higher.
Description : Is hammer mill is similar to dummy type, but it is provided with aspirator for cleaning grains. A) True B) False
Last Answer : True
Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow ... centrifugal pump, is always higher than that of volute type (D) All the above
Last Answer : (D) All the above
Description : The spike teeth are in Triangular harrow. a. Movable b. Adjustable d. None of the above
Last Answer : Ans - c. fixed
Description : The power tiller harrow is a mounted reciprocating comb type. A. Rear C. Right B. Front. D. None of the above
Last Answer : rear
Description : it is a Cultivator with tines or blades mounted on a power driven horizontal shaft. A. Disc cultivator. C Rotary cultivator B. Tine cultivator. D Trailed type cultivator
Last Answer : Rotary cultivator
Description : is pulled and guided from single hitch point but its weight is not supported by the tractor. A. Trailed type implement C. Semi mounted type implemented B. Mounted type implemented D. Automatic implemented
Last Answer : Trailed type implement
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these
Last Answer : (B) Loss of kinetic head
Description : A grinding wheel rotates at 3000 rpm. When power supply is cut off the wheel stops in 5 sec. The number of revolutions made by the wheel before coming to rest would be a.500 b.107 dynes c.250 d.3000 e.1000
Last Answer : c. 250
Description : The resultant of a force acting on a body will be zero, if the body a.Rotates with uniform acceleration b.Moves along a curved path c.Rotates d.Does not rotate e.Rotates with uniform deceleration
Last Answer : d. Does not rotate
Description : A 2 m long shaft rotates about one end at 20 rad/s. It begins to accelerate with ? = 10 rads/s2. After how long, in seconds, will the velocity of the free end reach 100 m/s? a.3 b.107 dynes c.5 d.6 e.7
Last Answer : a. 3
Description : A grinding wheel rotates at 3000 rpm. When power supply is cut-off the wheel stops in 10 seconds. The number of revolutions made by the wheel before coming to rest would be a.1500 b.3000 c.1000 d.250 e.500
Last Answer : d. 250
Description : The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero
Last Answer : e. Zero
Description : A flywheel weighs 400 kg and has a radius of gyration of 30 cm about its axis of rotation. It is mounted on a shaft subjected to a moment of 40 kgm. If the flywheel starts from restits speed after 3 seconds wil be a.10.9 rad/sec b.19.0 rad/sec c.51.2 rad/sec d.3.33 rad/sec e.16.35 rad/sec
Last Answer : d. 3.33 rad/sec
Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c
Last Answer : ans c