What Is The Use Of Ejector?

What Is The Use Of Ejector?
by

1 Answer

Answer :

Ejector is used to create Vacuum for process.
by

Related questions

The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

A cylindrical ejector having its height 2 m fills after every 10 minutes with a peak sewage discharge of 0.0157 cumec. The diameter of the ejector chamber, is A. 2.30 m B. 2.40 m C. 2.45 m D. 2.50 m

Description : A cylindrical ejector having its height 2 m fills after every 10 minutes with a peak sewage discharge of 0.0157 cumec. The diameter of the ejector chamber, is A. 2.30 m B. 2.40 m C. 2.45 m D. 2.50 m

Last Answer : ANS: C

Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Description : Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Last Answer : ANS: A

Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Description : Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Last Answer : ANS: A

In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Description : In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Last Answer : (C) Steam jet ejector with a barometric condenser

The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Description : The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Last Answer : (B) Entrainment separator

The steam ejector is used to (A) Remove condensate from the steam pipelines (B) Create vacuum (C) Superheat the steam (D) None of these

Description : The steam ejector is used to (A) Remove condensate from the steam pipelines (B) Create vacuum (C) Superheat the steam (D) None of these

Last Answer : (B) Create vacuum

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

An ejector is used to (A) Increase pressure (B) Increase temperature (C) Remove condensate (D) None of these

Description : An ejector is used to (A) Increase pressure (B) Increase temperature (C) Remove condensate (D) None of these

Last Answer : (D) None of these

Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Description : Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Last Answer : (D) Natural draft

When the head pumped against is less than the head of the fluid used for pumping, the usual device is a/an (A) Ejector (B) Blower (C) Injector (D) Airlift

Description : When the head pumped against is less than the head of the fluid used for pumping, the usual device is a/an (A) Ejector (B) Blower (C) Injector (D) Airlift

Last Answer : (D) Airlift

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

What is an air ejector?

Description : What is an air ejector?

Last Answer : An air ejector is a steam siphon that removes non-condensable gases from the condenser.

What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Description : What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Last Answer : Ejector: Ejector is used to remove the work piece from close fitted locators and is present behind the work piece. Ejector speed up the operation by reducing unloading time. This increases the ... [6] The combined mechanism used in Ejectors can be powered hydraulically or by compressed air. 

What is ejector? State its necessity in the design of jigs and fixtures.

Description : What is ejector? State its necessity in the design of jigs and fixtures.

Last Answer : Concept of ejector: A device, which is used to remove the work piece from the machine after completion of operation, is known as ejector. Necessity: In the design of jigs and fixture , ... been machined. Ejector speeds up the unloading of the work piece and thus increases the production rate.