When the head pumped against is less than the head of the fluid used for pumping, the usual device is a/an (A) Ejector (B) Blower (C) Injector (D) Airlift

When the head pumped against is less than the head of the fluid used
for pumping, the usual device is a/an
(A) Ejector
(B) Blower
(C) Injector
(D) Airlift
by

1 Answer

Answer :

(D) Airlift
by

Related questions

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The usual types of diesel injectors are : a) single hole injector b) multi hole injector c) long stem injector d) all of the mentioned

Description : The usual types of diesel injectors are : a) single hole injector b) multi hole injector c) long stem injector d) all of the mentioned

Last Answer : Answer: d Explanation: The types of diesel injectors are single hole injector, multi hole injector and long stem injector.

When the momentum of one fluid is used for moving another fluid, such a device is called a/an (A) Jet pump (B) Blower (C) Acid egg (D) None of these

Description : When the momentum of one fluid is used for moving another fluid, such a device is called a/an (A) Jet pump (B) Blower (C) Acid egg (D) None of these

Last Answer : (A) Jet pump

A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Description : A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Last Answer : (A) Less head & capacity

A fluid is pumped at the rate of 10 lb/sec to a height of 55 ft. The horse power required is __________ hp. (A) 1 (B) 10/55 (C) 5.5 (D) 1/55

Description : A fluid is pumped at the rate of 10 lb/sec to a height of 55 ft. The horse power required is __________ hp. (A) 1 (B) 10/55 (C) 5.5 (D) 1/55

Last Answer : (A) 1

If the chosen diameter of a pipe, is less than the economical diameter (A) Cost of pipe will be less (B) Head loss will be high (C) Cost of pumping will be more than saving (D) All the above

Description : If the chosen diameter of a pipe, is less than the economical diameter  (A) Cost of pipe will be less  (B) Head loss will be high  (C) Cost of pumping will be more than saving  (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) Head loss in smaller size pipes at equal velocities, is less (B) Cost of pumping is less in smaller size pipes (C) Cost of smaller pipes is comparatively more (D) None of these

Description : Pick up the correct statement from the following:  (A) Head loss in smaller size pipes at equal velocities, is less  (B) Cost of pumping is less in smaller size pipes  (C) Cost of smaller pipes is comparatively more  (D) None of these 

Last Answer : (D) None of these 

Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Description : Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Last Answer : (A) Keeping the heat transfer surface clean

Which of the following is not an advantage of fluidisation from transferoperation point of view?(A) Intimate contact of the fluid with all parts of the solid particles(B) Lower fluid pumping power requirement(C) Minimisation of temperature variation(D) Prevention of particle segregation

Description : Which of the following is not an advantage of fluidisation from transferoperation point of view? (A) Intimate contact of the fluid with all parts of the solid particles (B) Lower fluid pumping power requirement (C) Minimisation of temperature variation (D) Prevention of particle segregation

Last Answer : (B) Lower fluid pumping power requirement

For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Description : For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Last Answer : (A) Decreases

Optimum economic pipe diameter for fluid is determined by the (A) Viscosity of the fluid (B) Density of the fluid (C) Total cost considerations (pumping cost plus fixed cost of the pipe) (D) None of these

Description : Optimum economic pipe diameter for fluid is determined by the (A) Viscosity of the fluid (B) Density of the fluid (C) Total cost considerations (pumping cost plus fixed cost of the pipe) (D) None of these

Last Answer : (C) Total cost considerations (pumping cost plus fixed cost of the pipe)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

What was the reason for the Berlin Airlift?

Description : What was the reason for the Berlin Airlift?

Last Answer : Stalin blockaded the border between East Germany and WestGermany, cutting off rail and road shipments of supplies to WestBerlin. He hoped this would starve West Berlin into surrendering tohis control.The ... was performed to bring in supplies by air andprevent Stalin from succeeding in his plans.

How effectlively did the world leaders respond to the Burlin Airlift?

Description : How effectlively did the world leaders respond to the Burlin Airlift?

Last Answer : The Berlin airlift was very successful and managed to keep thepeople with goods.

What necessitated the Berlin airlift?

Description : What necessitated the Berlin airlift?

Last Answer : Feel Free to Answer

Who issues cargo airlift certifications?

Description : Who issues cargo airlift certifications?

Last Answer : Feel Free to Answer

What A blockade airlift and wall were all a part of this city during the Cold War.?

Description : What A blockade airlift and wall were all a part of this city during the Cold War.?

Last Answer : This is Berlin.

Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines? (A) Air filter (B) Fuel injector (C) Exhaust silencer (D) Battery

Description : Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines? (A) Air filter (B) Fuel injector (C) Exhaust silencer (D) Battery

Last Answer : Option B

In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Description : In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Last Answer : (C) Steam jet ejector with a barometric condenser

The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Description : The separation of liquid droplets from the vapor is done by a/an __________, in the evaporators. (A) Steam ejector (B) Entrainment separator (C) Compressor (D) Vacuum pump

Last Answer : (B) Entrainment separator

The steam ejector is used to (A) Remove condensate from the steam pipelines (B) Create vacuum (C) Superheat the steam (D) None of these

Description : The steam ejector is used to (A) Remove condensate from the steam pipelines (B) Create vacuum (C) Superheat the steam (D) None of these

Last Answer : (B) Create vacuum

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

An ejector is used to (A) Increase pressure (B) Increase temperature (C) Remove condensate (D) None of these

Description : An ejector is used to (A) Increase pressure (B) Increase temperature (C) Remove condensate (D) None of these

Last Answer : (D) None of these

Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Description : Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Last Answer : (D) Natural draft

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

Where is the fuel injector regulator tbi in a 1991 cchevrolet van g20 5.7l ?

Description : Where is the fuel injector regulator tbi in a 1991 cchevrolet van g20 5.7l ?

Last Answer : Take off the upper intake, the regulator is on the backside of the fuel injector unit spider.

The air-fuel ratio of the petrol engine is governed by A. fuel pump B. governor C. carburetor D. injector

Description : The air-fuel ratio of the petrol engine is governed by A. fuel pump B. governor C. carburetor D. injector

Last Answer : ANSWER : C

_______________ is used to enable cold starting, with out the use of a heater plug. a) Pintaux nozzle b) Multi hole injector c) Long stem injector d) Pintle nozzle

Description : _______________ is used to enable cold starting, with out the use of a heater plug. a) Pintaux nozzle b) Multi hole injector c) Long stem injector d) Pintle nozzle

Last Answer : Answer: a Explanation: Generally, intaux nozzle is used to enable cold starting, with out the use of a heater plug.

In pre-chamber and swirl type of combustion system ______________ is used. a) single hole injector b) multi hole injector c) long stem injector d) pintle nozzle

Description : In pre-chamber and swirl type of combustion system ______________ is used. a) single hole injector b) multi hole injector c) long stem injector d) pintle nozzle

Last Answer : Answer: d Explanation: In pre-chamber and swirl type of combustion system pintle nozzle is used and not the other nozzles.

Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

How to Change a Fuel Injector

Description : How to Change a Fuel Injector

Last Answer : How to Change a Fuel Injector Is your engine flooded with gas and your motor sputtering? It might be because your fuel injector is dirty or plugged up. Although it's not a very common dilemma ... arises, do not neglect this simple maintenance trick. Otherwise, you'll expect plenty of problems soon.

(i) Describe the principle of mechanical governor in fuel injection pump. (ii) State four types of injector nozzles

Description : (i) Describe the principle of mechanical governor in fuel injection pump. (ii) State four types of injector nozzles

Last Answer : (i) Working Principal of mechanical governor of FIP: The working principle of mechanical governor is illustrated in figure. When the engine speed tends to exceed the limit the weights fly apart. This causes ... ) Multi-hole nozzle 3) Long stem nozzle 4) Pintle nozzles 5) Pintuax nozzles 

Illustrate with neat sketch the construction of fuel injector

Description : Illustrate with neat sketch the construction of fuel injector

Last Answer : Diesel Fuel Injector: The injector assembly consists of - i) a needle valve ii) a compression spring iii) a nozzle iv) an injector body. When the fuel is supplied to lift the injection pump it ... and hence the valve opening pressure is controlled by adjusting the screw provided at the top.  

Describe the working of fuel injector with neat sketch

Description : Describe the working of fuel injector with neat sketch

Last Answer : Fuel Injector: The injector assembly consists of - i) a needle valve ii) a compression spring iii) a nozzle iv) an injector body When the fuel is supplied to lift the injection ... spring tension and hence the valve opening pressure is controlled by adjusting the screw provided at the top.

Describe the working of electronic fuel injector with the help of suitable sketch.

Description : Describe the working of electronic fuel injector with the help of suitable sketch.

Last Answer : Working of Electronic Fuel Injector: In MPFI system, Top feed fuel Injector is used. These injectors are solenoid-operated valves that are opened and closed by means of electric pulses from the ECU. The ... Pintle and discharge opening to form a fine spray pattern that has a cone shape.

While determining the yield of open wells by the pumping test (A) Velocity of recharging water, increases with depression head (B) Depression head resulting at critical velocity, is called critical depression head (C) Working head is generally limited to (D) Maximum safe yield of an open well, is expected at critical depression head

Description : While determining the yield of open wells by the pumping test  (A) Velocity of recharging water, increases with depression head  (B) Depression head resulting at critical velocity, is called critical ... (D) Maximum safe yield of an open well, is expected at critical depression head 

Last Answer : (D) Maximum safe yield of an open well, is expected at critical depression head 

Pick up the correct statement from the following: (A) The water level in a still well, represents the ground water table level (B) The difference between water table level and the water level in a well after pumping, is called depression head (C) The surface of water table surrounding a well during pumping, forms a cone of depression (D) All the above

Description : Pick up the correct statement from the following:  (A) The water level in a still well, represents the ground water table level  (B) The difference between water table level and the water ... water table surrounding a well during pumping, forms a cone of depression  (D) All the above 

Last Answer : (D) All the above 

You received a call from a father how has a son diagnosed recently with DM-I for six months, he said that he found his son lying down unconscious in his bedroom, What you will tell him if he is seeking for advise: a. Bring him as soon as possible to ER b. Call the ambulance c. Give him his usual dose of insulin d. Give him IM Glucagone e. Give him Sugar in Fluid per oral

Description : You received a call from a father how has a son diagnosed recently with DM-I for six months, he said that he found his son lying down unconscious in his bedroom, What you will tell him if he is ... Give him his usual dose of insulin d. Give him IM Glucagone e. Give him Sugar in Fluid per oral

Last Answer : Give him IM Glucagone

The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The non-clog pump which permits solid matter to pass out with the liquid sewage, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

A cylindrical ejector having its height 2 m fills after every 10 minutes with a peak sewage discharge of 0.0157 cumec. The diameter of the ejector chamber, is A. 2.30 m B. 2.40 m C. 2.45 m D. 2.50 m

Description : A cylindrical ejector having its height 2 m fills after every 10 minutes with a peak sewage discharge of 0.0157 cumec. The diameter of the ejector chamber, is A. 2.30 m B. 2.40 m C. 2.45 m D. 2.50 m

Last Answer : ANS: C

Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Description : Q No: 131 The most widely used pump for lifting sewage is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. Air pressure pump

Last Answer : ANS: A

Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Description : Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Last Answer : ANS: A

What Is The Use Of Ejector?

Description : What Is The Use Of Ejector?

Last Answer : Ejector is used to create Vacuum for process.

What is an air ejector?

Description : What is an air ejector?

Last Answer : An air ejector is a steam siphon that removes non-condensable gases from the condenser.

What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Description : What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Last Answer : Ejector: Ejector is used to remove the work piece from close fitted locators and is present behind the work piece. Ejector speed up the operation by reducing unloading time. This increases the ... [6] The combined mechanism used in Ejectors can be powered hydraulically or by compressed air. 

What is ejector? State its necessity in the design of jigs and fixtures.

Description : What is ejector? State its necessity in the design of jigs and fixtures.

Last Answer : Concept of ejector: A device, which is used to remove the work piece from the machine after completion of operation, is known as ejector. Necessity: In the design of jigs and fixture , ... been machined. Ejector speeds up the unloading of the work piece and thus increases the production rate.

Global warming deniers: what went wrong with sticking your head out the window to prove it's colder than usual?

Description : Global warming deniers: what went wrong with sticking your head out the window to prove it's colder than usual?

Last Answer : Maybe they’ve all melted?

Could Americans be less aware of the advantages of having all of the Canadian shoppers streaming across the border and pumping money into our economy?

Description : Could Americans be less aware of the advantages of having all of the Canadian shoppers streaming across the border and pumping money into our economy?

Last Answer : Blame it on the public education system. Maybe they wouldn’t gripe if it was legal to by medications in Canada. Washington gets Lipitor, Canada gets big jars of peanut butter