Bitumen of grade 80/100 means (A) Its penetration value is 8 mm (B) Its penetration value is 10 mm (C) Its penetration value is 8 to 10 mm (D) Its penetration value is 8 to 10 cm

Bitumen of grade 80/100 means
(A) Its penetration value is 8 mm
(B) Its penetration value is 10 mm
(C) Its penetration value is 8 to 10 mm
(D) Its penetration value is 8 to 10 cm
by

1 Answer

Answer :

Answer: Option C
by

Related questions

Penetration test on bitumen is used for determining its (A) Grade (B) Viscosity (C) Ductility (D) Temperature susceptibilit

Description : Penetration test on bitumen is used for determining its (A) Grade (B) Viscosity (C) Ductility (D) Temperature susceptibilit

Last Answer : Answer: Option A

Which of the following represents hardest grade of bitumen? (A) 30/40 (B) 60/70 (C) 80/100 (D) 100/120

Description : Which of the following represents hardest grade of bitumen? (A) 30/40 (B) 60/70 (C) 80/100 (D) 100/120

Last Answer : Answer: Option A

In the penetration macadam construction, the bitumen is (A) Sprayed after the aggregates are spread and compacted (B) Premixed with aggregates and then spread (C) Sprayed before the aggregates are spread and compacted (D) None of the above

Description : In the penetration macadam construction, the bitumen is (A) Sprayed after the aggregates are spread and compacted (B) Premixed with aggregates and then spread (C) Sprayed before the aggregates are spread and compacted (D) None of the above

Last Answer : Answer: Option A

A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Description : A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Last Answer : (D) 10 tonnes

Size of blast furnace grade coke is __________ mm. (A) 25-80 (B) 0-15 (C) 15-25 (D) > 100

Description : Size of blast furnace grade coke is __________ mm. (A) 25-80 (B) 0-15 (C) 15-25 (D) > 100

Last Answer : (A) 25-80

The ductility value of bitumen for suitability in road construction should not be less than (A) 30 cm (B) 40 cm (C) 50 cm (D) 60 cm

Description : The ductility value of bitumen for suitability in road construction should not be less than (A) 30 cm (B) 40 cm (C) 50 cm (D) 60 cm

Last Answer : Answer: Option C

In CBR test the value of CBR is calculated at (A) 2.5 mm penetration only (B) 5.0 mm penetration only (C) 7.5 mm penetration only (D) Both 2.5 mm and 5.0 mm penetrations

Description : In CBR test the value of CBR is calculated at (A) 2.5 mm penetration only (B) 5.0 mm penetration only (C) 7.5 mm penetration only (D) Both 2.5 mm and 5.0 mm penetrations

Last Answer : Answer: Option D

Road grade bitumen is produced from vacuum residue by its (A) Aeration (B) Pyrolysis (C) Hydrogenation (D) Steam reforming

Description : Road grade bitumen is produced from vacuum residue by its (A) Aeration (B) Pyrolysis (C) Hydrogenation (D) Steam reforming

Last Answer : (D) Steam reforming

According to ISI, bitumen is classified into (A) 2 grades (B) 4 grades (C) 8 grades (D) 10 grades

Description : According to ISI, bitumen is classified into (A) 2 grades (B) 4 grades (C) 8 grades (D) 10 grades

Last Answer : Answer: Option D

If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, 6 kg, 4 kg respectively, the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Last Answer : Answer: Option C

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

The nominal size of the modular brick is (A) 190 mm × 90 mm × 80 mm (B) 190 mm × 190 mm × 90 mm (C) 200 mm × 100 mm × 100 mm (D) 200 mm × 200 mm × 100 mm

Description : The nominal size of the modular brick is (A) 190 mm × 90 mm × 80 mm (B) 190 mm × 190 mm × 90 mm (C) 200 mm × 100 mm × 100 mm (D) 200 mm × 200 mm × 100 mm

Last Answer : Answer: Option C

An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 cm/hr, the maximum run-off rate based on 10 minute peak percentage of 16% from distributing graph of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs

Description : An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 ... of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs

Last Answer : Answer: Option C

For M 150 grade concrete (1:2:4) the moment of resistance factor is (A) 0.87 (B) 8.50 (C) 7.50 (D) 5.80

Description : For M 150 grade concrete (1:2:4) the moment of resistance factor is (A) 0.87 (B) 8.50 (C) 7.50 (D) 5.80

Last Answer : Answer: Option B

An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for maximum strength are: (A) b = 57.73 cm d = 81.65 cm (B) b = 81.65 cm d = 57.73 cm (C) b = 50.00 cm d = 50.00 cm (D) b = 40.00 cm d = 80.00 cm

Description : The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for  maximum strength are:  (A) b = 57.73 cm d = 81.65 cm  (B) b = 81.65 cm d = 57.73 cm  (C) b = 50.00 cm d = 50.00 cm  (D) b = 40.00 cm d = 80.00 cm 

Last Answer : (A) b = 57.73 cm d = 81.65 cm 

The minimum depth of building foundations on (A) Sandy soils is 80 cm to 100 cm (B) Clay soils is 90 cm to 160 cm (C) Rocky soils is 5 cm to 50 cm (D) All the above

Description : The minimum depth of building foundations on (A) Sandy soils is 80 cm to 100 cm (B) Clay soils is 90 cm to 160 cm (C) Rocky soils is 5 cm to 50 cm (D) All the above

Last Answer : Answer: Option D

On piles, the drop must be at least (A) 80 cm (B) 100 cm (C) 120 cm (D) 140 cm

Description : On piles, the drop must be at least (A) 80 cm (B) 100 cm (C) 120 cm (D) 140 cm

Last Answer : Answer: Option C

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

According to Indian standard specifications, 100 H6/g5 means that (A) Tolerance grade for the hole is 6 and for the shaft is 5 (B) Tolerance grade for the shaft is 6 and for the hole is 5 (C) Tolerance grade for the shaft is 4 to 8 and for the hole is 3 to 7 (D) Tolerance grade for the hole is 4 to 8 and for the shaft is 3 to 7

Description : According to Indian standard specifications, 100 H6/g5 means that (A) Tolerance grade for the hole is 6 and for the shaft is 5 (B) Tolerance grade for the shaft is 6 and for the hole is 5 (C) Tolerance grade for ... is 3 to 7 (D) Tolerance grade for the hole is 4 to 8 and for the shaft is 3 to 7

Last Answer : (A) Tolerance grade for the hole is 6 and for the shaft is 5

Optimum penetration of a .024 or .031 inch self-threading pin in dentin is . . . a. 0.5 mm b. 1.0 mm c. 2.0 mm d. 2.5 mm e. 3.0 mm

Description : Optimum penetration of a .024 or .031 inch self-threading pin in dentin is . . . a. 0.5 mm b. 1.0 mm c. 2.0 mm d. 2.5 mm e. 3.0 mm

Last Answer : c. 2.0 mm

Heat penetration rate in narrow coke ovens in high temperature carbonisation of coal is around __________ cm/hr. (A) 2.5 (B) 0.5 (C) 10 (D) 20

Description : Heat penetration rate in narrow coke ovens in high temperature carbonisation of coal is around __________ cm/hr. (A) 2.5 (B) 0.5 (C) 10 (D) 20

Last Answer : (A) 2.5

Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Last Answer : [ B ] 30 mm

Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Last Answer : [ B ] 30 mm

According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option A

For a poorly graded sub-grade soil, thickness of sub-base, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 30 cm

Description : For a poorly graded sub-grade soil, thickness of sub-base, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 30 cm

Last Answer : Answer: Option D

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

If the radius of curvature of a hill road is 50 m, the percentage grade compensation should be (A) 60/R (B) 70/R (C) 75/R (D) 80/R

Description : If the radius of curvature of a hill road is 50 m, the percentage grade compensation should be (A) 60/R (B) 70/R (C) 75/R (D) 80/R

Last Answer : Answer: Option C

A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The extension in the rod was 1 mm only. If Esteel = 2 × 106 kg/cm2 , the side of the rod, is (A) 1 cm (B) 1.5 cm (C) 2 cm (D) 2.5 cm

Description : A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The  extension in the rod was 1 mm only. If Esteel = 2 × 106  kg/cm2 , the side of the rod, is  (A) 1 cm  (B) 1.5 cm  (C) 2 cm  (D) 2.5 cm 

Last Answer : (C) 2 cm 

A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered by the piston to sliding with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Description : A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered ... with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Last Answer : c. 10900 kg

Consider the following statements: 1. Standard penetration test is commonly used for cohesionless soils. 2. Standard penetration test results in respect of a cohesionless soil are correlated to its density index and friction angle. 3. Use of H-value not corrected for overburden pressure leads to highly conservative design of footings at shallow depths. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. Standard penetration test is commonly used for cohesionless soils. 2. Standard penetration test results in respect of a cohesionless soil are correlated to its density index and friction angle. 3. Use of H- ... 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (a) 1, 2 & 3

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

Dimensions of Postcards is a) Max 100 X 150 mm & min 80 X 140 mm b) Max 105 X 149 mm & min 90 X 140 mm c) Max 150 X 200 mm & min 70X 140 mm d) None of these

Description : Dimensions of Postcards is a) Max 100 X 150 mm & min 80 X 140 mm b) Max 105 X 149 mm & min 90 X 140 mm c) Max 150 X 200 mm & min 70X 140 mm d) None of these

Last Answer : b) Max 105 X 149 mm & min 90 X 140 mm

Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Last Answer : c. 5mm

Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Description : Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Last Answer : b. 31.89 MPa

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Description : The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Last Answer : (c) 23

Softening point of bitumen to be used for read construction at a place where maximum temperature is 40°C should be (A) Less than 40°C (B) Greater than 40°C (C) Equal to 40°C (D) None of the above

Description : Softening point of bitumen to be used for read construction at a place where maximum temperature is 40°C should be (A) Less than 40°C (B) Greater than 40°C (C) Equal to 40°C (D) None of the above

Last Answer : Answer: Option B

The binder normally used in flexible pavement construction is (A) Cement (B) Lime (C) Bitumen (D) None of the above

Description : The binder normally used in flexible pavement construction is (A) Cement (B) Lime (C) Bitumen (D) None of the above

Last Answer : Answer: Option C

Which of the following represents a carpet of sand-bitumen mix without coarse aggregates? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Description : Which of the following represents a carpet of sand-bitumen mix without coarse aggregates? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Last Answer : Answer: Option B

Pavement is said to be flexible if it contains (A) Water bound macadam surface (B) Stabilised soil base constructed of lime cement or tar (C) Bitumen-bound stone layer of varying aggregates (D) All the above

Description : Pavement is said to be flexible if it contains (A) Water bound macadam surface (B) Stabilised soil base constructed of lime cement or tar (C) Bitumen-bound stone layer of varying aggregates (D) All the above

Last Answer : Answer: Option D

Percentage of free carbon in bitumen is (A) More than that in tar (B) Less than that in tar (C) Equal to that in tar(D) None of the above

Description : Percentage of free carbon in bitumen is (A) More than that in tar (B) Less than that in tar (C) Equal to that in tar (D) None of the above

Last Answer : Answer: Option B

Select the correct statement. (A) Quantity of binder required for tack coat is less than that required for prime coat (B) Prime coat treatment is given for plugging the voids in water bound macadam during bituminous road construction (C) Seal coat is the final coat over certain previous bituminous pavements (D) A bitumen primer is a high viscosity cutback

Description : Select the correct statement. (A) Quantity of binder required for tack coat is less than that required for prime coat (B) Prime coat treatment is given for plugging the voids in water ... the final coat over certain previous bituminous pavements (D) A bitumen primer is a high viscosity cutback

Last Answer : Answer: Option D

Bitumen paints offer (A) Pleasing surface (B) Hard surface (C) Smooth surface (D) Protective surface

Description : Bitumen paints offer (A) Pleasing surface (B) Hard surface (C) Smooth surface (D) Protective surface

Last Answer : Answer: Option D

Plastic bitumen is generally used for (A) Road pavements (B) Expansion joints (C) Crack fillings (D) None to these

Description : Plastic bitumen is generally used for (A) Road pavements (B) Expansion joints (C) Crack fillings (D) None to these

Last Answer : Answer: Option C

Bitumen emulsion is (A) A liquid containing bitumen in suspension (B) A paint (C) Used as anti-corrosive paint (D) All the above

Description : Bitumen emulsion is (A) A liquid containing bitumen in suspension (B) A paint (C) Used as anti-corrosive paint (D) All the above

Last Answer : Answer: Option D

The filler used in plastic bitumen, is (A) Shale powder (B) Talc powder (C) Asbestos powder (D) Plastic powder

Description : The filler used in plastic bitumen, is (A) Shale powder (B) Talc powder (C) Asbestos powder (D) Plastic powder

Last Answer : Answer: Option C

Bitumen felt (A) Is used as water proofing material (B) Is used as damp proofing material (C) Is made from bitumen and hessian fibres (D) All the above

Description : Bitumen felt (A) Is used as water proofing material (B) Is used as damp proofing material (C) Is made from bitumen and hessian fibres (D) All the above

Last Answer : Answer: Option D