Description : Which of the following manometer has highest sensitivity? (A) U-tube with water (B) Inclined U-tube (C) U-tube with mercury (D) Micro-manometer with water
Last Answer : Answer: Option D
Description : Small pressure differences in liquids is measured using a/an (A) U-tube manometer (B) Inclined tube manometer (C) Pitot tube (D) None of these
Last Answer : (B) Inclined tube manometer
Description : Very small pressure difference (< 5 mm water column) can be most conveniently measured by a/an __________ manometer. (A) U-tube water (B) U-tube mercury (C) Inclined tube mercury (D) Inclined tube water
Last Answer : (D) Inclined tube water
Description : Choose the wrong statement. Alcohol is used in manometer, because (A) Its vapour pressure is low (B) It provides suitable meniscus for the inclined tube (C) Its density is less (D) It provides longer length for a given pressure difference
Last Answer : Answer: Option A
Description : Least force required to draw a body up the inclined plane is W sin (plane inclination + friction angle) applied in the direction (A) Along the plane (B) Horizontally (C) Vertically (D) At an angle equal to the angle of friction to the inclined plane
Last Answer : (D) At an angle equal to the angle of friction to the inclined plane
Description : Working principle of manometer comprises of balancing a coloumn of liquid against the pressure to be measured. Inclined tube manometer is especially used for the measurement of __________ pressure. (A) Small differential (B) Atmospheric (C) Absolute (D) Gage
Last Answer : (A) Small differential
Description : Pressure of the order of 10" torr can be measured by (A) Bourdon tube (B) Pirani Gauge (C) Micro-manometer (D) Lonisation gauge
Description : Compare U tube manometer and well type manometer
Last Answer : U-tube and well type manometer Sr.No. U-tube manometer well type manometer 1 Both legs are having same cross section area Both legs are having different cross section area ... cross section area. 5 Difference in heights in measured. Single height is measured.
Description : The angle A lies in the third quadrant and it satisfies the equation 4 (sin^2x + cos x) = 1. What is the measure of angle A? -Maths 9th
Last Answer : answer:
Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)
Last Answer : (A) cos α = (dr + dp)/(dr + df)
Description : Why is an inclined manometer used ?
Last Answer : It is used to extend the scale of the instrument. Because the manometer is at an angle to the vertical.
Description : A member is balanced at its end by two inclined members carrying equal forces. For equilibrium the angle between the inclined bars must be (A) 3° (B) 45° (C) 90° (D) 120°
Last Answer : (D) 120°
Description : The angle of internal friction of soil mass is the angle whose (A) Tangent is equal to the rate of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on ... on any internal inclined plane to the normal pressure acting on the plane (D) None of these
Description : While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)
Last Answer : (C) 20 (sec - 1)
Description : If `sin^4 alpha + 4 cos^4 beta + 2 = 4sqrt2 sin alpha cos beta ; alpha, beta in [0,pi],` then `cos(alpha+beta) - cos(alpha - beta)` is equal to :
Last Answer : If `sin^4 alpha + 4 cos^4 beta + 2 = 4sqrt2 sin alpha cos beta ; alpha, beta in [0,pi],` then `cos(alpha+beta ... sqrt(2)` B. `0` C. `sqrt(2)` D. `-1`
Description : If cos X = a/b, then sin X is equal to: a (b 2 -a 2 )/b b b−a/b c √(b 2 -a 2 )/b d √b−a/b
Last Answer : c √(b 2 -a 2 )/b
Description : 1 – cos 2 A is equal to: a sin 2 A b tan 2 A c 1 – sin 2 A d sec 2 A
Last Answer : a sin 2 A
Description : According to the Snell's law if an electromagnetic wave is incident in a medium (refractive index n1) on another medium (refractive index m2); (A) The angle of incidence is equal to the angle of refraction (B) The angle of ... r) is given by sin i (C) Both (a) and (b) (D) Neither (a) nor (b)
Last Answer : Answer: Option B
Description : With the rise of temperature, the sensitivity of a bubble tube (A) Decreases (B) Increases (C) Remains unaffected (D) None of the above
Last Answer : (A) Decreases
Description : The sensitivity of a bubble tube can be increased by (A) Increasing the diameter of the tube (B) Decreasing the length of bubble (C) Increasing the viscosity of liquid (D) Decreasing the radius of curvature of tube
Last Answer : (A) Increasing the diameter of the tube
Description : The desired sensitivity of a bubble tube with 2 mm divisions is 30". The radius of the bubble tube should be (A) 13.75 m (B) 3.44 m (C) 1375 m (D) None of these
Last Answer : (A) 13.75 m
Description : Flow rate of high velocity flue gas discharged through a stack to the atmosphere can be most conveniently measured by a (A) Pitot tube (B) Manometer (C) Rotameter (D) None of these
Last Answer : (A) Pitot tube
Description : Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10
Last Answer : (C) > 12.5
Description : A Pitot tube indicates 5 cm of water (manometer) when it is being used for measuring velocity of air. The velocity of air in m/sec is (A) 5 (B) 14.1 (C) 56.22 (D) 28.2
Last Answer : (D) 28.2
Description : Air velocity in ducts can be measured by using and manometer a) Orifice meter b) Borden gauge c) Pitot tube d) Anemometer
Last Answer : Pitot tube
Description : What pressure measuring device consists of a coiled hollow tube that tends to straighten out when the tube is subjected to an internal pressure? A. Aneroid B. Manometer C. Bourdon pressure gage D. Barometer
Last Answer : Bourdon pressure gage
Description : What instrument is used to measure atmospheric pressure? A. Pitot tube B. Wind vane C. Barometer D. Manometer
Last Answer : Barometer
Description : Which of the following is NOT an instrument used to measure pressure? A. Bourdon tube B. Pitot tube C. Aneroid D. Manometer
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : The angle which an inclined plane makes with the horizontal when a body placed on it is about to move down is known as angle of (A) Friction (B) Limiting friction (C) Repose (D) Kinematic friction
Last Answer : (C) Repose
Description : A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant ... inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17
Last Answer : (C) 12°
Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°
Description : A plane inclined at an angle to the horizontal at which the soil is expected to stay in the absence of any lateral support, is known as (A) Natural slope line (B) Repose line (C) The line (D) All the above
Description : The angle of repose of a soil is the maximum angle which the outer face of the soil mass makes (A) With the horizontal (B) With the vertical (C) With the perpendicular to the inclined plane of the soil (D) None of these
Description : An open vessel of water is accelerated up an inclined plane. The free water surface will (A) Be horizontal (B) Make an angle in direction of inclination of inclined plane (C) Make an angle in opposite direction to inclination of inclined plane (D) Any one of above is possible
Last Answer : Answer: Option C
Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there
Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there
Description : When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes
Last Answer : c. equal in magnitude
Description : The resolved part of the resultant of two forces inclined at an angle 9 in a given direction is equal to
Last Answer : The resolved part of the resultant of two forces inclined at an angle 9 in a given direction is equal to the algebraic sum of the resolved parts of the forces in the given direction.
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Description : Explaining the derivatives of sin, cos and toa?
Last Answer : answer:I am assuming this isn't homework, as it is summer and from what you wrote it appears you are merely curious, so I think it's legal for me to do the proof here for you (don't strike me down, ... proof for that as well. By toa do you mean tangent? I can prove that one too if you'd like.
Description : What's the key to remembering how to draw each of the different trigonometric function graphs? (i.e. sin, cos, tan)
Last Answer : SOH – sin CAH – cos TOA – tan sin = opposite over hypotenuse cos = adjacent over hypotenuse tan = opposite over adjacent
Description : How to use sin, cos, and tan on a TI-84+Silver Edition?
Last Answer : answer:This may work, haven't tried a real problem yet . here are the steps in changing it from radian to degrees 1. turn on your TI-83 plus 2. press the MODE button near the top of your ... down to options and move the highlight from radian to degree, press enter and clear you're good to go
Description : What is SIN, TAN, COS?
Last Answer : Wikipedia knows.
Description : Which of the following represents shearing? a.(x, y) → (x+shx, y+shy) b.(x, y) → (ax, by) c.(x, y) → (x cos(θ)+y sin(θ), -x sin(θ)+y cos(θ)) d.(x, y) → (x+shy, y+shx)
Last Answer : d.(x, y) → (x+shy, y+shx)
Description : The original coordinates of the point in polar coordinates are a.X’=r cos (Ф +ϴ) and Y’=r cos (Ф +ϴ) b.X’=r cos (Ф +ϴ) and Y’=r sin (Ф +ϴ) c.X’=r cos (Ф -ϴ) and Y’=r cos (Ф -ϴ) d.X’=r cos (Ф +ϴ) and Y’=r sin (Ф -ϴ)
Last Answer : b.X’=r cos (Ф +ϴ) and Y’=r sin (Ф +ϴ)
Description : For any two real number a b and , we defined aRb if and only if sin^2a + cos^2b = 1. The relation R is -Maths 9th
Last Answer : (d) an equivalence relationGiven, a R b ⇒ sin2a + cos2b = 1 Reflexive: a R a ⇒ sin2 a + cos2 a = 1 ∀ a ∈ R (True) Symmetric: a R b ⇒ sin2 a + cos2 b = 1 ⇒ 1 - cos2 a + 1 - sin2 b = 1 ⇒ sin2 b + ... + cos2 b + sin2 b + cos2 c = 2 ⇒ sin2 a + cos2 c = 1 ⇒ a R c (True)∴ R is an equivalence relation.
Description : If A lies in the third quadrant and 3 tan A – 4 = 0, then what is the value of 5 sin 2 A + 3 sin A + 4 cos A? -Maths 9th