Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Half the angle of nip, (α), for a roll crusher is given by
(where, dr, dp and df are diameters of crushing rolls, feed particles and rolls
gap respectively).
(A) cos α = (dr + dp)/(dr + df)
(B) cos α = (dr + df)/(dr + dp)
(C) tan α = (dr + dp)/(dr + df)
(D) sin α = (dr + dp)/(dr + df)
by

1 Answer

Answer :

(A) cos α = (dr + dp)/(dr + df)
by

Related questions

The reduction ratio for grinders is defined as (where, Df and Dp are average diameters of feed and product respectively). (A) Df /Dp (B) Dp /Df (C) Df - Dp (D) None of these

Description : The reduction ratio for grinders is defined as (where, Df and Dp are average diameters of feed and product respectively). (A) Df /Dp (B) Dp /Df (C) Df - Dp (D) None of these

Last Answer : (A) Df /Dp

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

. Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Description : . Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Last Answer : (B) μ ≥ tan α

Angle of nip of the crushing rolls does not depend upon the (A) Diameter of the rolls (B) Speed of the rolls (C) Product size (D) Feed size

Description : Angle of nip of the crushing rolls does not depend upon the (A) Diameter of the rolls (B) Speed of the rolls (C) Product size (D) Feed size

Last Answer : (B) Speed of the rolls

What is the usual value of angle of nip for crushing of ordinary rock in smooth steel crushing rolls? (A) 16° (B) 32° (C) 40° (D) 46°

Description : What is the usual value of angle of nip for crushing of ordinary rock in smooth steel crushing rolls? (A) 16° (B) 32° (C) 40° (D) 46°

Last Answer : (B) 32°

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

In a roll crusher, both the rolls (A) Have the same diameter (B) Are rotated towards each other (C) Run either at the same or different speeds (D) All (A), (B) and (C

Description : In a roll crusher, both the rolls (A) Have the same diameter (B) Are rotated towards each other (C) Run either at the same or different speeds (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls in rotation per second (rps) D = diameter of rolls, m). (A) 3.6 V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Last Answer : (A) 3.6 V.W.Dr.ρ

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Description : Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

ECE Board Exam April 1997 Sound intensity is given as A. df/dP B. dE/dp C. dA/dP D. dP/dA

Description : ECE Board Exam April 1997 Sound intensity is given as A. df/dP B. dE/dp C. dA/dP D. dP/dA

Last Answer : D. dP/dA

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Description : Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Last Answer : (A) Impact

What's the key to remembering how to draw each of the different trigonometric function graphs? (i.e. sin, cos, tan)

Description : What's the key to remembering how to draw each of the different trigonometric function graphs? (i.e. sin, cos, tan)

Last Answer : SOH – sin CAH – cos TOA – tan sin = opposite over hypotenuse cos = adjacent over hypotenuse tan = opposite over adjacent

How to use sin, cos, and tan on a TI-84+Silver Edition?

Description : How to use sin, cos, and tan on a TI-84+Silver Edition?

Last Answer : answer:This may work, haven't tried a real problem yet . here are the steps in changing it from radian to degrees 1. turn on your TI-83 plus 2. press the MODE button near the top of your ... down to options and move the highlight from radian to degree, press enter and clear you're good to go

What is SIN, TAN, COS?

Description : What is SIN, TAN, COS?

Last Answer : Wikipedia knows.

If A lies in the third quadrant and 3 tan A – 4 = 0, then what is the value of 5 sin 2 A + 3 sin A + 4 cos A? -Maths 9th

Description : If A lies in the third quadrant and 3 tan A – 4 = 0, then what is the value of 5 sin 2 A + 3 sin A + 4 cos A? -Maths 9th

Last Answer : answer:

If tan x = b/a , then what is the value of a cos 2x + b sin 2x? -Maths 9th

Description : If tan x = b/a , then what is the value of a cos 2x + b sin 2x? -Maths 9th

Last Answer : answer:

Prove that (sin A + sin 3A + sin 5A + sin7 A)/(Cos A + Cos3 A + cos5 A + cos7 A) = tan 4A. -Maths 9th

Description : Prove that (sin A + sin 3A + sin 5A + sin7 A)/(Cos A + Cos3 A + cos5 A + cos7 A) = tan 4A. -Maths 9th

Last Answer : answer:

If cosec A = 2, then the value of 1/(tan A) + (sin A)/(1+cos A) is -Maths 9th

Description : If cosec A = 2, then the value of 1/(tan A) + (sin A)/(1+cos A) is -Maths 9th

Last Answer : answer:

What is the value of sin A cos A tan A + cos A sin A cot A ? -Maths 9th

Description : What is the value of sin A cos A tan A + cos A sin A cot A ? -Maths 9th

Last Answer : answer:

`(i) int e^(x). "[log (sec x+tan x) + sec x dx "` `(ii) int (e^(-x)(cos x-sin x))/(cos^(2) x) dx`

Description : `(i) int e^(x). "[log (sec x+tan x) + sec x dx "` `(ii) int (e^(-x)(cos x-sin x))/(cos^(2) x) dx`

Last Answer : `(i) int e^(x). "[log (sec x+tan x) + sec x dx "` `(ii) int (e^(-x)(cos x-sin x))/(cos^(2) x) dx`

`(i) int(1)/(sqrt(1-x^(2)).cos^(-1) x)dx` `(ii) int (sin(tan^(-1)x))/(1+x^(2))dx`

Description : `(i) int(1)/(sqrt(1-x^(2)).cos^(-1) x)dx` `(ii) int (sin(tan^(-1)x))/(1+x^(2))dx`

Last Answer : `(i) int(1)/(sqrt(1-x^(2)).cos^(-1) x)dx` `(ii) int (sin(tan^(-1)x))/(1+x^(2))dx`

` (i) int sqrt(1+ sin .(x)/(2)dx)` `(ii) int (1+cos 4x)/(cot x- tan x)dx`

Description : ` (i) int sqrt(1+ sin .(x)/(2)dx)` `(ii) int (1+cos 4x)/(cot x- tan x)dx`

Last Answer : ` (i) int sqrt(1+ sin .(x)/(2)dx)` `(ii) int (1+cos 4x)/(cot x- tan x)dx`

Consider the matrix function `A(x)=[{:(cos^(-1)x,sin^(-1)x,cosec^(-1)x),(sin^(-1)x,sec^(-1)x,tan^(-1)x),(cosec^(-1)x,tan^(-1)x,cot^(-1)x):}]` and `B =

Description : Consider the matrix function `A(x)=[{:(cos^(-1)x,sin^(-1)x,cosec^(-1)x),(sin^(-1)x,sec^(-1)x,tan^(-1)x),(cosec^(-1)x,tan^(-1)x,cot^(-1)x):}]` and `B =

Last Answer : Consider the matrix function `A(x)=[{:(cos^(-1)x,sin^(-1)x,cosec^(-1)x),(sin^(-1)x,sec^(-1)x,tan^(-1)x),( ... )=-A(x)` D. `A(x) + A(-x) = - piI_(3)`

Let `theta ,phi in [0,2pi]` be such that `2 cos theta (1-sin phi)=sin^2 theta ((tan)theta/2+(cot)theta/2) cos phi -1, tan(2pi-theta) > 0 and -1 &lt

Description : Let `theta ,phi in [0,2pi]` be such that `2 cos theta (1-sin phi)=sin^2 theta ((tan)theta/2+(cot)theta/2) cos phi -1, tan(2pi-theta) > 0 and -1 <

Last Answer : Let `theta ,phi in [0,2pi]` be such that `2 cos theta (1-sin phi)=sin^2 theta ((tan)theta/2+(cot)theta/2) ... (3pi)/(2)` D. `(3pi)/(2) lt phi lt 2pi`

15. Which of the following is correct?(1) \( \tan 1>\tan 2 \)(2) \( \tan 2>\tan 1 \)(3) \( \sin 1\cos 2 \)

Description : 15. Which of the following is correct?(1) \( \tan 1>\tan 2 \)(2) \( \tan 2>\tan 1 \)(3) \( \sin 1\cos 2 \)

Last Answer : 15. Which of the following is correct? (1) \( \tan 1>\tan 2 \) (2) \( \tan 2>\tan 1 \) (3) \( \sin 1\cos 2 \)

If tan A = 4/3 and sin A = 4/5 then cos A = —————– a. 4/5 b. 3/5 c. 3⁄4 d.9/11

Description : If tan A = 4/3 and sin A = 4/5 then cos A = —————– a. 4/5 b. 3/5 c. 3⁄4 d.9/11

Last Answer : b. 3/5

The value of 2 tan 2 45°+ cos 2 30° − sin 2 60° is (a) 0 (b) 1 (c) -2 (d) 2

Description : The value of 2 tan 2 45°+ cos 2 30° − sin 2 60° is (a) 0 (b) 1 (c) -2 (d) 2

Last Answer : (d) 2

In right triangle ABC, right angled at C, if tan A = 1, then the value of 2 sin A cos A is (a) 0 (b) 1 (c) – 1 (d) 2

Description : In right triangle ABC, right angled at C, if tan A = 1, then the value of 2 sin A cos A is (a) 0 (b) 1 (c) – 1 (d) 2

Last Answer : (b) 1

1 – cos 2 A is equal to: a sin 2 A b tan 2 A c 1 – sin 2 A d sec 2 A

Description : 1 – cos 2 A is equal to: a sin 2 A b tan 2 A c 1 – sin 2 A d sec 2 A

Last Answer : a sin 2 A

Numerical aperture is expressed as the a) NA = sin θa b) NA = cos θa c) NA = tan θa d) NA = sec θa

Description : Numerical aperture is expressed as the a) NA = sin θa b) NA = cos θa c) NA = tan θa d) NA = sec θa

Last Answer : a) NA = sin θa

Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers (C) States that the work required to form particle of any size from very large feed is proportional to the square root of the volume to surface ratio of the product (D) States that the work required for the crushing is proportional to the new surface created

Description : Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers ( ... (D) States that the work required for the crushing is proportional to the new surface created

Last Answer : (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law

Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Last Answer : (C) Consumes more power

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Description : According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Last Answer : (B) √(S/V)

. Which of the following equations is Rittinger's crushing law? (Where P = power required by the machine, m = feed rate, k = a constant, Ds̅a & D̅sb = volume surface mean diameter of feed & product respectively.) (A) P/m = K/ √Dp (B) P/m = K . ln D̅sa /D̅sb (C) P/m = K . (1/ D̅sb - 1/Ds̅a ) (D) None of these

Description : . Which of the following equations is Rittinger's crushing law? (Where P = power required by the machine, m = feed rate, k = a constant, Ds̅a & D̅sb = volume surface mean diameter of feed & product respectively.) (A) P/m = K/ ... K . ln D̅sa /D̅sb (C) P/m = K . (1/ D̅sb - 1/Ds̅a ) (D) None of these

Last Answer : (C) P/m = K . (1/ D̅sb - 1/Ds̅a )

The initial gap between the extra full-length leaf and the graduated-length leaf before the assembly, is called as (A) clearance (B) nip (C) gap

Description : The initial gap between the extra full-length leaf and the graduated-length leaf before the assembly, is called as (A) clearance (B) nip (C) gap

Last Answer : (B) nip

Nip is the initial gap between extra full length leaf and the graduated length leaf before the assembly. a) True b) False

Description : Nip is the initial gap between extra full length leaf and the graduated length leaf before the assembly. a) True b) False

Last Answer : a) True

Size reduction of the __________ can be suitably done by ball mills, crushing rolls and rod mills. (A) Metalliferous ores (B) Non-metallic ores (C) Basic slags (D) Asbestos & mica

Description : Size reduction of the __________ can be suitably done by ball mills, crushing rolls and rod mills. (A) Metalliferous ores (B) Non-metallic ores (C) Basic slags (D) Asbestos & mica

Last Answer : (A) Metalliferous ores

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Last Answer : (A) Hammer mills

What is the purpose of the pet bottle crusher? Where can I buy the best plastic crushing machine?

Description : What is the purpose of the pet bottle crusher? Where can I buy the best plastic crushing machine?

Last Answer : May I ask why you wish to buy the best crushing machine if you don't even know the purpose behind it? The purpose would be to save space when throwing away or recycling plastic bottles. Since 2 ... lift back up with the handle. Repeat for each plastic bottle. BONUS. Works for aluminum cans as well.

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

For a given Reynold number as d/D for an orifice increases, Cd will (where, d & D are orifice & pipe diameters respectively). (A) Increase (B) Decrease (C) Remain constant (D) Either (A) or (B); depends on other factors

Description : For a given Reynold number as d/D for an orifice increases, Cd will (where, d & D are orifice & pipe diameters respectively). (A) Increase (B) Decrease (C) Remain constant (D) Either (A) or (B); depends on other factors

Last Answer : (A) Increase

The angle A lies in the third quadrant and it satisfies the equation 4 (sin^2x + cos x) = 1. What is the measure of angle A? -Maths 9th

Description : The angle A lies in the third quadrant and it satisfies the equation 4 (sin^2x + cos x) = 1. What is the measure of angle A? -Maths 9th

Last Answer : answer:

In order to increase sensitivity of U-tube manometer, one leg is usually inclined by angle . Sensitivity of inclined tube to sensitivity of U-tube is equal to (A) Sin (B) 1/Sin (C) Cos (D) 1/Cos

Description : In order to increase sensitivity of U-tube manometer, one leg is usually inclined by angle . Sensitivity of inclined tube to sensitivity of U-tube is equal to (A) Sin (B) 1/Sin (C) Cos (D) 1/Cos

Last Answer : Answer: Option B