The height of a water column equivalent to a pressure of 0.15 MPa is (A) 15.3 m (B) 25.3 m (C) 35.3 m (D) 45.3 m

The height of a water column equivalent to a pressure of 0.15 MPa is
(A) 15.3 m
(B) 25.3 m
(C) 35.3 m
(D) 45.3 m
by

2 Answers

Answer :

Answer: Option A
by

Answer :

The height of a water column equivalent to a pressure of 0.15 MPa can be calculated using the hydrostatic equation:

Pressure (P) = Density of water (rho) * Acceleration due to gravity (g) * Height (h)

where g is the acceleration due to gravity, which is approximately 9.8 m/s^2.

Substituting the known values into the equation and solving for h gives:

h = P / (rho * g)

= 0.15 MPa / (1000 kg/m^3 * 9.8 m/s^2)

= 0.15 m

Therefore, the height of the water column would be approximately 0.15 meters.
by

Related questions

In case of foundations on sandy soil, maximum permissible differential settlement, is usually limited to (A) 15 mm (B) 25 mm (C) 35 mm (D) 45 m

Description : In case of foundations on sandy soil, maximum permissible differential settlement, is usually limited to (A) 15 mm (B) 25 mm (C) 35 mm (D) 45 mm

Last Answer : Answer: Option B

A vertical column of water will be supported to what height by standard atmospheric pressure.  a. 33.9 ft  b. 45 ft  c. 67 ft  d. 25.46 ft ho= Po/Yo

Description : A vertical column of water will be supported to what height by standard atmospheric pressure.  a. 33.9 ft  b. 45 ft  c. 67 ft  d. 25.46 ft ho= Po/Yo

Last Answer : 33.9 ft

Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than (A) 35 MPa and 42 MPa (B) 42 MPa and 35 MPa (C) 42 MPa and 53 MPa (D) 53 MPa and 42 MPa

Description : Cube strength of controlled concrete to be used for pre-tensioned and post-tensioned work respectively should not be less than (A) 35 MPa and 42 MPa (B) 42 MPa and 35 MPa (C) 42 MPa and 53 MPa (D) 53 MPa and 42 MPa

Last Answer : Answer: Option B

Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75

Last Answer : (b) 15, 25, 40 and 75

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

Pick up the correct statement from the following (A) The ratio of the up flux and down flux just above the snow surface, is called albedo (B) Spectral albedo of snow is calculated for the semi-infinite snow thickness (C) Water equivalent height of snow is the height of water column obtained by melting snow (D) All of these

Description : Pick up the correct statement from the following (A) The ratio of the up flux and down flux just above the snow surface, is called albedo (B) Spectral albedo of snow is calculated for the semi- ... equivalent height of snow is the height of water column obtained by melting snow (D) All of these

Last Answer : Answer: Option D

For a clay slope of height of 10 m, the stability number is 0.05, = 2.0 t/m3 , C = 2.5 t/m2 , the critical height of the slope of the soil, is (A) 4.0 m (B) 12.5 m (C) 25.0 m (D) 15.0 m

Description : For a clay slope of height of 10 m, the stability number is 0.05, = 2.0 t/m3 , C = 2.5 t/m2 , the critical height of the slope of the soil, is (A) 4.0 m (B) 12.5 m (C) 25.0 m (D) 15.0 m

Last Answer : (C) 25.0 m

A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

A machine requires an effort of 10 kg to lift a load of 250 kg and an effort of 13 kg for a load of 400 kg. The effort required to lift a load of 500 kg will be a.25 kg b.107 dynes c.15 kg d.35 kg e.45 kg

Description : A machine requires an effort of 10 kg to lift a load of 250 kg and an effort of 13 kg for a load of 400 kg. The effort required to lift a load of 500 kg will be a.25 kg b.107 dynes c.15 kg d.35 kg e.45 kg

Last Answer : c. 15 kg

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

Daily output of urea in grams is (A) 10 to 20 (B) 15 to 25 (C) 20 to 30 (D) 35 to 45

Description : Daily output of urea in grams is (A) 10 to 20 (B) 15 to 25 (C) 20 to 30 (D) 35 to 45

Last Answer : Answer : C

The least distance of distinct vision is – (1) 35 cm (2) 25 cm (3) 45 cm (4) 15 cm

Description : The least distance of distinct vision is – (1) 35 cm (2) 25 cm (3) 45 cm (4) 15 cm

Last Answer : (2) 25 cm Explanation: Least distance of distinct vision is the minimum object's distance that is able to produce a distinct image on the retina. This distance is about 25 cm from the eye. However, it varies with age. For infants the least distance of distinct vision is about 5 to 8 cm.

Ash content in the middling coal (a byproduct of coal washeries) in India ranges between __________ percent. (A) 15 to 25 (B) 35 to 45 (C) 55 to 75 (D) 75

Description : Ash content in the middling coal (a byproduct of coal washeries) in India ranges between __________ percent. (A) 15 to 25 (B) 35 to 45 (C) 55 to 75 (D) 75

Last Answer : (B) 35 to 45

How many HP for tractor is suitable suitable for 20 hectares farm? A. 10-15 C. 20-25. B. 30-35 D. 40-45

Description : How many HP for tractor is suitable suitable for 20 hectares farm? A. 10-15 C. 20-25. B. 30-35 D. 40-45

Last Answer : 20-25

What are the commonest congenitally missing teeth:VERY CONTROVERSIAL BUT SEE THE SAMPLE QUESTIONS FROM ADC IT’S THE ANSWER A. 12, 22 B. 35, 45 ACC TO CAMERON C. 15, 25 D. 33, 43

Description : What are the commonest congenitally missing teeth:VERY CONTROVERSIAL BUT SEE THE SAMPLE QUESTIONS FROM ADC IT’S THE ANSWER A. 12, 22 B. 35, 45 ACC TO CAMERON C. 15, 25 D. 33, 43

Last Answer : A. 12, 22

Write a program to create a vector with five elements as (5, 15, 25, 35, 45). Insert new element at 2nd position. Remove 1st and 4th element from vector.

Description : Write a program to create a vector with five elements as (5, 15, 25, 35, 45). Insert new element at 2nd position. Remove 1st and 4th element from vector.

Last Answer : import java.util.*; class VectorDemo { public static void main(String[] args) { Vector v = new Vector(); v.addElement(new Integer(5)); v.addElement(new Integer(15)); v.addElement(new ... .addElement(new Integer(45)); System.out.println("Original array elements are "); for(int i=0;i

The least distance of distinct vision is (1) 35 cm (2) 25 cm (3) 45 cm (4) 15 cm

Description : The least distance of distinct vision is (1) 35 cm (2) 25 cm (3) 45 cm (4) 15 cm

Last Answer : 25 cm

P and Q can do a piece of job in 24 days; Q and R can do it in 30 days while R and P can finish it in 40 days. If P, Q, Rworks together, in how many days will they finish the job? In how many days will each one of them finish it, working alone? A) 15,25,35,45 B) 20,30,40,120 C) 20,30,40,50 D) 20,25,30,60

Description : P and Q can do a piece of job in 24 days; Q and R can do it in 30 days while R and P can finish it in 40 days. If P, Q, Rworks together, in how many days will they finish the job? In how many days will each ... finish it, working alone? A) 15,25,35,45 B) 20,30,40,120 C) 20,30,40,50 D) 20,25,30,60 

Last Answer : B Time taken by (P + Q) to finish the job = 24days. (P + Q)'s 1 day's job = 1/24 Time taken by (Q +R) to finish the job = 30days. (Q + R)'s 1 day's job = 1/30 Time taken by (R + P) to finish the ... - {(P + Q)'s 1 day's job } = (1/20 -1/24)=1/120 Hence, R alone can finish the job in 120 days.

The normal road land width for a major district road in open area, is (A) 45 m (B) 25 m (C) 15 m (D) 12 m

Description : The normal road land width for a major district road in open area, is (A) 45 m (B) 25 m (C) 15 m (D) 12 m

Last Answer : Answer: Option B

Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m

Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the  sight on the down-slope, must be less than  (A) 30 m  (B) 25 m  (C) 20 m  (D) 15 m 

Last Answer : (B) 25 m 

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Last Answer : (c) 0.0037

Depth of borings for soil investigation, is generally kept below low water level (A) 30 m (B) 35 m (C) 45 m (D) 40 m

Description : Depth of borings for soil investigation, is generally kept below low water level (A) 30 m (B) 35 m (C) 45 m (D) 40 m

Last Answer : (C) 45 m

The bearing capacity of granite is generally (A) 5 to 10 kg/cm2 (B) 15 to 20 kg/cm2 (C) 30 to 35 kg/cm2 (D) 40 to 45 kg/cm2

Description : The bearing capacity of granite is generally (A) 5 to 10 kg/cm2 (B) 15 to 20 kg/cm2 (C) 30 to 35 kg/cm2 (D) 40 to 45 kg/cm2

Last Answer : Answer: Option C

The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Description : The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Last Answer : Answer: Option C

A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400°. Determine the heat added.  a) 1378.7 kJ  b) 1348.5 kJ  c) 1278,7 kJ  d) 1246,5 kJ Formula: Q = (h2 – p2v2) –(h1 –p1v1)

Description : A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400°. Determine the heat added.  a) 1378.7 kJ  b) 1348.5 kJ  c) 1278,7 kJ  d) 1246,5 kJ Formula: Q = (h2 – p2v2) –(h1 –p1v1)

Last Answer : 1378.7 kJ

If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Description : If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55

Last Answer : Answer: Option D

High strength of concrete requires a water cement ratio of [ A ] 0.10 to 0.15 [ B ] 0.25 to 0.30 [ C ] 0.45 to 0.60 [ D ] 0.75 to 0.90

Description : High strength of concrete requires a water cement ratio of [ A ] 0.10 to 0.15 [ B ] 0.25 to 0.30 [ C ] 0.45 to 0.60 [ D ] 0.75 to 0.90

Last Answer : [ B ] 0.25 to 0.30

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

Steam is throttled to 0.1 MPa with 20 degrees of superheat. (a) What is the quality of throttled steam if its pressure is 0.75 MPa (b) What is the enthalpy of the process?  a) 97.6%,2713 kJ/kg  b) -97.6%, 2713 kJ/kg  c) 87.6%,3713 kJ/kg  d) -87.6%, 3713 kJ/kg

Description : Steam is throttled to 0.1 MPa with 20 degrees of superheat. (a) What is the quality of throttled steam if its pressure is 0.75 MPa (b) What is the enthalpy of the process?  a) 97.6%,2713 kJ/kg  b) -97.6%, 2713 kJ/kg  c) 87.6%,3713 kJ/kg  d) -87.6%, 3713 kJ/kg

Last Answer : 97.6%,2713 kJ/kg

Wet steam at 1 MPa flowing through a pipe is throttled to a pressure of 0.1 MPa. If the throttling temperature is110°C, What is the quality of the steam in the pipe?  a) 96%  b) 86%  c) 76%  d) 66%

Description : Wet steam at 1 MPa flowing through a pipe is throttled to a pressure of 0.1 MPa. If the throttling temperature is110°C, What is the quality of the steam in the pipe?  a) 96%  b) 86%  c) 76%  d) 66%

Last Answer : 96%

A steam calorimeter receives steam from a pipe at 0.1 MPa and 20°SH. For a pipe steam pressure of 2 MPa, what is the quality of the steam?  a) 95.56%  b) 70.10%  c) 95.20%  d) 85.10% Formula: h1 = hf1 + x1hfg1

Description : A steam calorimeter receives steam from a pipe at 0.1 MPa and 20°SH. For a pipe steam pressure of 2 MPa, what is the quality of the steam?  a) 95.56%  b) 70.10%  c) 95.20%  d) 85.10% Formula: h1 = hf1 + x1hfg1

Last Answer : 265.4°C, 430.7kJ/kg, 71.4kJ/kg, 1.0327kJ/(kg)(K),502.1 kJ/kg

Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration. b) 10-15 mm Hg water pressure. A measure of 10–15 mm Hg water pressure would indicate that the cuff is underinflated. c) 30-35 mm Hg water pressure. A measure of 30–35 mm Hg water pressure would indicate that the cuff is overinflated. d) 0-5 mm Hg water pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Description : Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the ... pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Last Answer : a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration.

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

Out of 100 kcal/second of incident radiant energy on the surface of a thermally transparent body, 300 kcal/second is reflected back. If the transmissivity of the body is 0.25, the emissivity of the surface will be (A) 0.35 (B) 0.45 (C) 0.55 (D) 0.85

Description : Out of 100 kcal/second of incident radiant energy on the surface of a thermally transparent body, 300 kcal/second is reflected back. If the transmissivity of the body is 0.25, the emissivity of the surface will be (A) 0.35 (B) 0.45 (C) 0.55 (D) 0.85

Last Answer : (B) 0.45

One gram of glucose produces how much fat or oil (A) 0.25 g (B) 0.35 g (C) 0.45 g (D) 0.32 g

Description : One gram of glucose produces how much fat or oil (A) 0.25 g (B) 0.35 g (C) 0.45 g (D) 0.32 g

Last Answer : (C) 0.45 g

Assume postal rates for 'light letters' are: $0.25 up to 10 grams; $0.35 up to 50 grams; $0.45 up to 75 grams; $0.55 up to 100 grams. Which test inputs (in grams) would be selected using boundary value analysis? A. 0, 9,19, 49, 50, 74, 75, 99,100 B. 10, 50, 75,100, 250, 1000 C. 0, 1,10,11, 50, 51, 75, 76,100,101 D. 25, 26, 35, 36, 45, 46, 55, 56

Description : Assume postal rates for 'light letters' are: $0.25 up to 10 grams; $0.35 up to 50 grams; $0.45 up to 75 grams; $0.55 up to 100 grams. Which test inputs (in grams) would be selected using boundary value analysis? A. 0, 9,19, ... C. 0, 1,10,11, 50, 51, 75, 76,100,101 D. 25, 26, 35, 36, 45, 46, 55, 56

Last Answer : C. 0, 1,10,11, 50, 51, 75, 76,100,101

A problem Drum ( 3 ft. diameter ; 6 ft. height ) is field with a fluid whose density is 50 lb/ft^3. Determine the total volume of the fluid.  A. 42.41 ft^3  B.44.35 ft^3  C.45.63 ft^3  D.41.23 ft^3 Formula: Vf = (pi d^2 h) / 4

Description : A problem Drum ( 3 ft. diameter ; 6 ft. height ) is field with a fluid whose density is 50 lb/ft^3. Determine the total volume of the fluid.  A. 42.41 ft^3  B.44.35 ft^3  C.45.63 ft^3  D.41.23 ft^3 Formula: Vf = (pi d^2 h) / 4

Last Answer : 42.41 ft^3

At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Description : At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Last Answer : c. Between 95 cm (38 inches) and 115 cm ( 45 inches)

Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Description : Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Last Answer : (iii) 40 to 45 mm

Column efficiency is measured in terms of number of theoretical plates, which is: A. Inversely related to height equivalent to theoretical plates B. Directly related to the peak width C. Directly related to height equivalent to theoretical plates D. Inversely related to the peak width

Description : Column efficiency is measured in terms of number of theoretical plates, which is: A. Inversely related to height equivalent to theoretical plates B. Directly related to the peak width C. Directly related to height equivalent to theoretical plates D. Inversely related to the peak width

Last Answer : Inversely related to height equivalent to theoretical plates 

A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Last Answer : (a) 2.87Mpa

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

Crushing strength of a good building stone should be more than (A) 50 MPa (B) 100 MPa (C) 150 MPa (D) 200 MPa

Description : Crushing strength of a good building stone should be more than (A) 50 MPa (B) 100 MPa (C) 150 MPa (D) 200 MPa

Last Answer : Answer: Option B

According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Description : According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Last Answer : Answer: Option C