A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1 tonne. The force required on plunger is equal to (A) 10 kg (B) 100 kg (C) 1000 kg (D) 1 kg

A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight
of 1 tonne. The force required on plunger is equal to
(A) 10 kg
(B) 100 kg
(C) 1000 kg
(D) 1 kg
by

1 Answer

Answer :

Answer: Option A
by

Related questions

A hydraulic press has a ram of 10 cms in diameter and a plunger of 1 cm in diameter. The force required on the plunger to raise a weight of 10 tons on the ram is __________ kg. (A) 10 (B) 100 (C) 1000 (D) 10000

Description : A hydraulic press has a ram of 10 cms in diameter and a plunger of 1 cm in diameter. The force required on the plunger to raise a weight of 10 tons on the ram is __________ kg. (A) 10 (B) 100 (C) 1000 (D) 10000

Last Answer : (B) 100

If the gross vehicle weight of a truck is 30 tonne and rolling resistance is 30 kg/tonne, then the tractive effort required to keep the truck moving at a uniform speed is (A) 30 kg (B) 300 kg (C) 900 kg (D) 1000 kg

Description : If the gross vehicle weight of a truck is 30 tonne and rolling resistance is 30 kg/tonne, then the tractive effort required to keep the truck moving at a uniform speed is (A) 30 kg (B) 300 kg (C) 900 kg (D) 1000 kg

Last Answer : (C) 900 kg

A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Description : A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump

Last Answer : (B) A cylinder and a plunger

Pick up the correct statement from the following: (A) Air lift pumps are generally used for pumping water from deep wells (B) Jet pumps are generally used for pumping water from small wells (C) The hydraulic ram works on the principle of water hammer (D) All the above

Description : Pick up the correct statement from the following: (A) Air lift pumps are generally used for pumping water from deep wells (B) Jet pumps are generally used for pumping water from small wells (C) The hydraulic ram works on the principle of water hammer (D) All the above

Last Answer : (D) All the above

The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Last Answer : (B) 102 kg

A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The rolling resistance of the road will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Description : A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The ... will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Last Answer : (C) 40 kg/tonne

For melting one tonne of cast iron (A) 700 m3 air is required (B) 20 kg limestone is required (C) One quintal coke is required (D) All the above

Description : For melting one tonne of cast iron (A) 700 m3 air is required (B) 20 kg limestone is required (C) One quintal coke is required (D) All the above

Last Answer : Answer: Option D

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

A body weighing one tonne falls through 8 cm on to a spring of stiffness 500 kg/cm the spring will be compressed through a.8 cm b.6 cm c.4 cm d.10 cm e.12 cm

Description : A body weighing one tonne falls through 8 cm on to a spring of stiffness 500 kg/cm the spring will be compressed through a.8 cm b.6 cm c.4 cm d.10 cm e.12 cm

Last Answer : a. 8 cm

The grade resistance factor for an earth moving machine can be obtained by multiplying grade percentage by a factor approximately equal to (A) 2 kg/tonne (B) 6 kg/tonne (C) 9 kg/tonne (D) 20 kg/tonne

Description : The grade resistance factor for an earth moving machine can be obtained by multiplying grade percentage by a factor approximately equal to (A) 2 kg/tonne (B) 6 kg/tonne (C) 9 kg/tonne (D) 20 kg/tonne

Last Answer : (C) 9 kg/tonne

A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance of 40 kg per tonne, then the drawbar pull of the tractor will (A) Reduce by 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Description : A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance ... 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Last Answer : (A) Reduce by 200 kg

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Last Answer : Answer: Option C

The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm

Last Answer : [ B ] 50 mm

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

On most smooth hard surfaced roads, rolling resistance to moving vehicles, ranges from (A) 5 kg to 7 kg/tonne (B) 7 kg to 9 kg/tonne (C) 9 kg to 11 kg/tonne (D) 11 kg to 13 kg/tonne

Description : On most smooth hard surfaced roads, rolling resistance to moving vehicles, ranges from (A) 5 kg to 7 kg/tonne (B) 7 kg to 9 kg/tonne (C) 9 kg to 11 kg/tonne (D) 11 kg to 13 kg/tonne

Last Answer : Answer: Option C

The maximum rimpull in the first gear of a tractor while towing a load is 6300 kg. The tractor weighs 12.5 tonnes and is operating along a 2 percent upgrade and the rolling resistance is 45 kg/tonne. Pull available for towing the load is (A) 3425 kg (B) 5515 kg (C) 4350 kg (D) 2975 kg

Description : The maximum rimpull in the first gear of a tractor while towing a load is 6300 kg. The tractor weighs 12.5 tonnes and is operating along a 2 percent upgrade and the rolling resistance is 45 kg/tonne. Pull available for towing the load is (A) 3425 kg (B) 5515 kg (C) 4350 kg (D) 2975 kg

Last Answer : (B) 5515 kg

Gradient resistance of moving vehicles along down slopes, is (A) + 7 kg/tonne (B) + 9 kg/tonne (C) - 9 kg/tonne (D) - 7 kg/tonne

Description : Gradient resistance of moving vehicles along down slopes, is (A) + 7 kg/tonne (B) + 9 kg/tonne (C) - 9 kg/tonne (D) - 7 kg/tonne

Last Answer : Answer: Option C

A machine requires an effort of 10 kg to lift a load of 250 kg and an effort of 13 kg for a load of 400 kg. The effort required to lift a load of 500 kg will be a.25 kg b.107 dynes c.15 kg d.35 kg e.45 kg

Description : A machine requires an effort of 10 kg to lift a load of 250 kg and an effort of 13 kg for a load of 400 kg. The effort required to lift a load of 500 kg will be a.25 kg b.107 dynes c.15 kg d.35 kg e.45 kg

Last Answer : c. 15 kg

An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

A 3.2 m diameter balloon is filled with Helium. The total weight of balloon, gas and pay load is 10 kg kg. In an isothermal atmosphere having conditions identical to N.T.P. the balloon will rise to a height of about a.6000 m b.1500 m c.3000 m d.2000 m e.1000 m

Description : A 3.2 m diameter balloon is filled with Helium. The total weight of balloon, gas and pay load is 10 kg kg. In an isothermal atmosphere having conditions identical to N.T.P. the balloon will rise to a height of about a.6000 m b.1500 m c.3000 m d.2000 m e.1000 m

Last Answer : a. 6000 m

In a hydraulic lift system the output force is greater than the input force because?

Description : In a hydraulic lift system the output force is greater than the input force because?

Last Answer : A

In a hydraulic lift system the output force is greater than the input force because?

Description : In a hydraulic lift system the output force is greater than the input force because?

Last Answer : A

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered by the piston to sliding with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Description : A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered ... with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Last Answer : c. 10900 kg

A body whose true weight is 14 kg appears to weigh 15 kg when weighed with the help of a spring balance in a moving lift. The acceleration of the lift at the time was a.1 m/sec2 b.0.7 m/sec2 c.0.5 m/sec2 d.1.4 m/sec2 e.0.35 m/sec2

Description : A body whose true weight is 14 kg appears to weigh 15 kg when weighed with the help of a spring balance in a moving lift. The acceleration of the lift at the time was a.1 m/sec2 b.0.7 m/sec2 c.0.5 m/sec2 d.1.4 m/sec2 e.0.35 m/sec2

Last Answer : b. 0.7 m/sec2

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is (A) 2.75 cm (B) 3.00 cm (C) 3.50 cm (D) 4.25 cm

Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm  for an eccentric load 100 t for non-development of tension, is  (A) 2.75 cm  (B) 3.00 cm  (C) 3.50 cm  (D) 4.25 cm

Last Answer : (D) 4.25 cm

In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm

Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm

Last Answer : Answer: Option D

For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head of 30 m. The minimum required horse power, is (A) 10 H.P. (B) 15 H.P. (C) 18 H.P. (D) 20 H.P.

Description : For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head  of 30 m. The minimum required horse power, is  (A) 10 H.P.  (B) 15 H.P.  (C) 18 H.P.  (D) 20 H.P. 

Last Answer : (D) 20 H.P. 

Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Description : Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Last Answer : Answer: Option D

If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Description : If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Last Answer : Answer: Option C

How much work has done to lift a 1000 kg block?

Description : How much work has done to lift a 1000 kg block?

Last Answer : That depends how high you lift it.The work is mgh (mass xgravity x height). If the mass is in kilograms, gravity is innewton/kilogram (Earth gravity is about 9.8 newton/kilogram), andthe height is in meters, then the work will be in joules.

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

A syringe has a volume of 10.0 cm^3 at pressure 1 atm. If you plug the end so that no gas can escape and push the plunger down,

Description : A syringe has a volume of 10.0 cm^3 at pressure 1 atm. If you plug the end so that no gas can escape and push the plunger down,

Last Answer : A syringe has a volume of 10.0 cm3 at pressure 1 atm. If you plug the end so that no gas can ... the final volume to change the pressure to 3.5 atm?

The moving parts of a machine which weigh 1 tonne perform vertical simple harmonic motion with an amplitude of 2.5 cm and a period of 0.5 sec. The base of the machine weighs 3 tonnes and rests on the ground. Maximum reactions on the ground would be a.3.6 tonnes b.2.4 tonnes c.4.0 tonnes d.4.8 tonnes e.4.4 tonnes

Description : The moving parts of a machine which weigh 1 tonne perform vertical simple harmonic motion with an amplitude of 2.5 cm and a period of 0.5 sec. The base of the machine weighs 3 tonnes and rests on the ground. Maximum ... would be a.3.6 tonnes b.2.4 tonnes c.4.0 tonnes d.4.8 tonnes e.4.4 tonnes

Last Answer : e. 4.4 tonnes

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Description : If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Last Answer : (C) 1/20,000

In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal a.the force applied on A must be equal to that on B b.at least one man on side B should be removed c.infinite force will be required to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Description : In a tug of war, five men pull a rope to the left at A and six moen pull the rope at B. A weight of 5 kg is hung vertically from the centre of the rope. In order that the rope AB be horizontal ... to be applied at both ends d.the force required on A must not be equal to that on B e.107 dynes

Last Answer : c. infinite force will be required to be applied at both ends

A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Description : A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Last Answer : (B) 0.2275 mm

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

Single-mode step-index cable has a core diameter in the range of ∙ A. 100 to 1000 micrometer ∙ B. 50 to 100 micrometer ∙ C. 2 to 15 micrometer ∙ D. 5 to 20 micrometer

Description : Single-mode step-index cable has a core diameter in the range of ∙ A. 100 to 1000 micrometer ∙ B. 50 to 100 micrometer ∙ C. 2 to 15 micrometer ∙ D. 5 to 20 micrometer

Last Answer : . 2 to 15 micrometer

A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half left hand span. The horizontal thrust at the support will be (A) 10.8 tonnes (B) 1.08 tonnes (C) 1.8 tonnes (D) 0.8 tonnes

Description : A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m  and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half  left hand span ... A) 10.8 tonnes  (B) 1.08 tonnes  (C) 1.8 tonnes  (D) 0.8 tonnes 

Last Answer : (B) 1.08 tonnes 

If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

For M 150 mix concrete, according to I.S. specifications, local bond stress, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Description : For M 150 mix concrete, according to I.S. specifications, local bond stress, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option B