Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm
Last Answer : Answer: Option C
Description : The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm
Last Answer : (c) 50mm
Description : If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is (A) 40 (B) 45 (C) 50 (D) 55
Last Answer : Answer: Option D
Description : In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above
Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)
Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)
Description : Percentage content of silica in window glass, is (A) 40 to 45 (B) 50 to 55 (C) 60 to 65 (D) 70 to 75
Description : A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1 tonne. The force required on plunger is equal to (A) 10 kg (B) 100 kg (C) 1000 kg (D) 1 kg
Last Answer : Answer: Option A
Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time
Last Answer : Answer: Option B
Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm
Last Answer : [ C ] 40 mm
Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm
Description : For the construction of cement concrete dams, the maximum permissible size of the aggregates, is (A) 40 mm (B) 50 mm (C) 60 mm (D) 70 mm
Description : The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm
Last Answer : [ A ] 25 mm
Description : For reinforced concrete work, aggregates having a nominal size of -------- are generally used [ A ] 20 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm
Last Answer : [ A ] 20 mm
Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times
Last Answer : a. increased by 8 times
Description : The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm
Description : The shape factor of standard rolled beam section varies from (A) 1.10 to 1.20 (B) 1.20 to 1.30 (C) 1.30 to 1.40 (D) 1.40 to 1.50
Last Answer : (A) 1.10 to 1.20
Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope ... arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E
Last Answer : (D) 200/E
Description : The development length of bars in compression is taken as [ A ] 30 times bar diameter [ B ] 40 times bar diameter [ C ] 50 times bar diameter [ D ] 12 times bar diameter
Last Answer : [ A ] 30 times bar diameter
Description : What is the co-efficient of contraction, if a fluid jet discharging from a 50 mm diameter orifice has a 40 mm diameter at its vena-contracta? (A) 0.64 (B) 1.65 (C) 0.32 (D) 0.94
Last Answer : (A) 0.64
Description : Vicat apparatus is used for (A) Fineness test (B) Consistency test (C) Test for setting time (D) Test for tensile strength
Description : Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa
Description : A hydraulic press has a ram of 10 cms in diameter and a plunger of 1 cm in diameter. The force required on the plunger to raise a weight of 10 tons on the ram is __________ kg. (A) 10 (B) 100 (C) 1000 (D) 10000
Last Answer : (B) 100
Description : A wire of mild steel has initial length 1.5 m and diameter 0.60 mm is extended by 6.3 mm
Last Answer : A wire of mild steel has initial length 1.5 m and diameter 0.60 mm is extended by 6.3 mm when a ... is 2.1 1011 N/m2, calculate the force applied.
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : The sum of the percentage of tricalcium silicate and dicalcium silicate for Portland cement varies from. (a) 50 to 60% (b) 60 to 70% (c) 70 to 80% (d) 80 to 90%
Last Answer : (c) 70 to 80%
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : A converging lens forms a three times magnified image of an object, which can be take on a screen. If the focal length of the lens is 30 cm, then the distance of the object from the lens is (a) - 55 cm (b) - 50 cm (c) - 45 cm (d) - 40 cm
Last Answer : (d) - 40 cm
Description : Two trains of equal length are running on parallel lines in the same direction at 46 km/hr and 36 km/hr. The faster train passes the slower train in 36 seconds. The length of each train is: A.40 m B.55 m C.65 m D.50 m E.None of these
Last Answer : Answer- D (50) Explanation – Relative speed= total lengths/time (46-36) x 5/18 = [L + L ] / 36 10 x (5/18) x36 x (1/2)= L L=50 m
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : A jet of water discharging from a 40 mm diameter orifice has a diameter of 32 mm at its vena contracta. The coefficient of contraction is (A) 0.46 (B) 0.64 (C) 0.78 (D) 0.87
Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444
Last Answer : A 0.144
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550
Last Answer : A. 575
Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112
Last Answer : a) 0.147
Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41
Last Answer : d) 41
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550
Last Answer : a) 575
Description : Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm
Last Answer : (iii) 50 mm*
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N
Last Answer : (C) 35 N
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : The minimum clear cover for R.C.C. columns shall be (A) Greater of 40 mm or diameter (B) Smaller of 40 mm or diameter (C) Greater of 25 mm or diameter (D) Smaller of 25 mm or diameter
Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm
Description : The Effective length of braced column generally varies…………the unsupported length of the column [ A ] 0.25 to 0.50 times [ B ] 0.50 to 1.00 times [ C ] 1.00 to 1.50 times [ D ] 2.00 to 2.50 times
Last Answer : [ B ] 0.50 to 1.00 times
Description : The efficiency of a pumping set, is generally assumed (A) 50 % (B) 55 % (C) 60 % (D) 65 %
Last Answer : (D) 65 %
Description : The population of a city in 2000 is 50,000. The average increase in population over last 8 decades is 7500 and average incremental increase during 8 decades is 750. The population of the city based on incremental method, in ... (A) 55,000 (B) 60,500 (C) 66,500 (D) 72,500
Last Answer : (C) 66,500
Description : Standard disc plough diameter size is A. 40 to 60 cm C. 70 to 90 cm B. 60 to 90 cm D. 50 to 70 cm
Last Answer : 60 to 90 cm
Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg
Last Answer : (B) 102 kg
Description : 95% (by volume) of LPG at 760 mm Hg pressure will evaporate at__________ °C. (A) 2 (B) -40 (C) 30 (D) 55
Last Answer : (A) 2
Description : Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm
Last Answer : (iii) 40 to 45 mm