If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P

If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed
by a force through its centroidal longitudinal axis, the compressive stress in concrete, is
(A) P/A
(B) A/P
(C) P/2A
(D) 2A/P
by

1 Answer

Answer :

Answer: Option A
by

Related questions

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is increased by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Last Answer : Answer: Option C

If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Description : If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Last Answer : Answer: Option B

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P

Description : A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P

Last Answer : Answer: Option C

A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Description : A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Last Answer : (d) Parabolic, with convexity downward

If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

If the maximum dip of a parabolic tendon carrying tension P is h and the effective length of the pre-stressed beam is L, the upward uniform pressure will be (A) 8hp/l (B) 8hp/l² (C) 8hl/p (D) 8hl/p²

Description : If the maximum dip of a parabolic tendon carrying tension P is h and the effective length of the pre-stressed beam is L, the upward uniform pressure will be (A) 8hp/l (B) 8hp/l² (C) 8hl/p (D) 8hl/p²

Last Answer : Answer: Option B

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Description : The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Last Answer : Answer: Option C

The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at the neutral axis, is (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A

Description : The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at  the neutral axis, is  (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A

Last Answer : (C) 3F/2A

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

A pre-stressed concrete member is preferred because (A) Its dimensions are not decided from the diagonal tensile stress (B) Large size of long beams carrying large shear force need not be adopted (C) Removal of cracks in the members due to shrinkage (D) All the above

Description : A pre-stressed concrete member is preferred because (A) Its dimensions are not decided from the diagonal tensile stress (B) Large size of long beams carrying large shear force need not be adopted (C) Removal of cracks in the members due to shrinkage (D) All the above

Last Answer : Answer: Option D

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these

Description : The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these

Last Answer : B. Zero at the point other than centroidal axis

The bending stress in a curved beam is (A) Zero at the centroidal axis (B) Zero at the point other than centroidal axis (C) Maximum at the neutral axis (D) None of these

Description : The bending stress in a curved beam is (A) Zero at the centroidal axis (B) Zero at the point other than centroidal axis (C) Maximum at the neutral axis (D) None of these

Last Answer : (B) Zero at the point other than centroidal axis

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress

In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Description : In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Last Answer : (d) 0.360 fck . Xu

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Description : A beam is said to be of uniform strength, if (A) B.M. is same throughout the beam (B) Shear stress is same throughout the beam (C) Deflection is same throughout the beam (D) Bending stress is same at every section along its longitudinal axis

Last Answer : (D) Bending stress is same at every section along its longitudinal axis

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Last Answer : Answer: Option C

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Description : For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Last Answer : Answer: Option C

The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force acting along the circumference, is known as (A) Yield stress(B) Longitudinal stress (C) Hoop stress (D) Circumferential stress

Description : The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force  acting along the circumference, is known as  (A) Yield stress  (B) Longitudinal stress  (C) Hoop stress  (D) Circumferential stress 

Last Answer : (C) Hoop stress

A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section (C) Distance of the C.G. of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Last Answer : Answer: Option D

In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Description : In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Last Answer : ANS: D

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Description : When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Last Answer : (a) Bond stress

A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above

Description : In a reinforced concrete beam , the shear stress distribution above the neutral axis following a (a) A straight line (b) Circular curve (c) Parabolic curve (d) All the above

Last Answer : (c) Parabolic curve

A reinforced concrete beam will crack if tensile stress set up in the concrete below the neutral axis is (a) More than the permissible stress (b) Less than the permissible stress (c) Equal to the permissible stress (d) All the above.

Description : A reinforced concrete beam will crack if tensile stress set up in the concrete below the neutral axis is (a) More than the permissible stress (b) Less than the permissible stress (c) Equal to the permissible stress (d) All the above.

Last Answer : (a) More than the permissible stress

If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Description : If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Last Answer : (a) Increase

A tank of uniform cross-sectional area (A) containing liquid upto height (H1) has an orifice of cross￾sectional area (a) at its bottom. The time required to bring the liquid level from H1 to H2 will be (A) 2A × d × a × 2g) (B) 2A × d × a × 2g) (C) 2A × - d × a × 2g) (D) 2A × 3/2 - 3/2)/Cd × a × 2g)

Description : A tank of uniform cross-sectional area (A) containing liquid upto height (H1) has an orifice of cross￾sectional area (a) at its bottom. The time required to bring the liquid level from H1 to H2 will be (A) 2A d a 2g) (B) 2A d ... 2g) (C) 2A - d a 2g) (D) 2A 3/2 - 3/2)/Cd a 2g)

Last Answer : Answer: Option C

A pre-stressed concrete member (A) Is made of concrete (B) Is made of reinforced concrete (C) Is stressed after casting (D) Possesses internal stresses

Description : A pre-stressed concrete member (A) Is made of concrete (B) Is made of reinforced concrete (C) Is stressed after casting (D) Possesses internal stresses

Last Answer : Answer: Option D

The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm

Description : The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm

Last Answer : Answer: Option D

High strength concrete is used in pre-stressed member (A) To overcome high bearing stresses developed at the ends (B) To overcome bursting stresses at the ends (C) To provide high bond stresses (D) All the above

Description : High strength concrete is used in pre-stressed member (A) To overcome high bearing stresses developed at the ends (B) To overcome bursting stresses at the ends (C) To provide high bond stresses (D) All the above

Last Answer : Answer: Option D

In a pre-stressed member it is advisable to use (A) Low strength concrete only (B) High strength concrete only (C) Low strength concrete but high tensile steel (D) High strength concrete and high tensile

Description : In a pre-stressed member it is advisable to use (A) Low strength concrete only (B) High strength concrete only (C) Low strength concrete but high tensile steel (D) High strength concrete and high tensile

Last Answer : Answer: Option D

In pre-stressed concrete (A) Forces of tension and compression change but lever arm remains unchanged (B) Forces of tension and compressions remain unchanged but lever arm changes with the moment (C) Both forces of tension and compression as well as lever arm change (D) Both forces of tension and compression as well as lever arm remain unchanged

Description : In pre-stressed concrete (A) Forces of tension and compression change but lever arm remains unchanged (B) Forces of tension and compressions remain unchanged but lever arm changes with the moment ( ... arm change (D) Both forces of tension and compression as well as lever arm remain unchanged

Last Answer : Answer: Option B

A pre-stressed concrete pile is (A) Easy to handle (B) Lighter in weight (C) Extremely durable (D) All the above

Description : A pre-stressed concrete pile is (A) Easy to handle (B) Lighter in weight (C) Extremely durable (D) All the above

Last Answer : Answer: Option D

If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

The ratio of moments of inertia of a triangular section about its base and about a centroidal axis parallel to its base, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 3.0

Description : The ratio of moments of inertia of a triangular section about its base and about a centroidal axis  parallel to its base, is  (A) 1.0  (B) 1.5  (C) 2.0  (D) 3.0 

Last Answer : (D) 3.0 

longitudinal bars and lateral stirrups, is (A) Stress in concrete × area of concrete (B) Stress in steel × area of steel (C) Stress in concrete × area of concrete + Stress in steel × area of steel (D) None of these

Description : longitudinal bars and lateral stirrups, is (A) Stress in concrete × area of concrete (B) Stress in steel × area of steel (C) Stress in concrete × area of concrete + Stress in steel × area of steel (D) None of these

Last Answer : Answer: Option C

The neutral axis corresponding to balanced section condition is termed as [ A ] Critical neutral axis [ B ] Centroidal neutral axis [ C ] Balanced neutral axis [ D ] All the above

Description : The neutral axis corresponding to balanced section condition is termed as [ A ] Critical neutral axis [ B ] Centroidal neutral axis [ C ] Balanced neutral axis [ D ] All the above

Last Answer : [ A ] Critical neutral axis

In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Last Answer : Answer: Option B

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D