Boiler draught of 10 mm water column is equivalent to (A) 1 kgf/m2 (B) 10 kgf/m2 (C) 10 kgf/mm2 (D) 1 kgf/mm2

Boiler draught of 10 mm water column is equivalent to (A) 1 kgf/m2
(B) 10 kgf/m2
(C) 10 kgf/mm2
(D) 1 kgf/mm2
by

1 Answer

Answer :

(B) 10 kgf/m2
by

Related questions

If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

Which one is not an induced draught furnace? (A) Blast furnace stove (B) Sintering furnace (C) High pressure boiler (D) None of these

Description : Which one is not an induced draught furnace? (A) Blast furnace stove (B) Sintering furnace (C) High pressure boiler (D) None of these

Last Answer : (A) Blast furnace stove

Normal temperature and pressure (N.T.P.) corresponds to (A) 0°C and 760 mm Hg (B) 15°C and 760 mm Hg (C) 20°C and 760 mm Hg (D) 0°C and 1 kgf/cm2

Description : Normal temperature and pressure (N.T.P.) corresponds to (A) 0°C and 760 mm Hg (B) 15°C and 760 mm Hg (C) 20°C and 760 mm Hg (D) 0°C and 1 kgf/cm2

Last Answer : (C) 20°C and 760 mm Hg

Stress may be expressed in Newtons (A) Per millimetre square (N/mm2 ) (B) Per centimetre square (N/cm2 ) (C) Per metre square (N/m2 ) (D) None of these

Description : Stress may be expressed in Newtons  (A) Per millimetre square (N/mm2 )  (B) Per centimetre square (N/cm2 )  (C) Per metre square (N/m2 )  (D) None of these 

Last Answer : (A) Per millimetre square (N/mm2 )

The pressure measured with the help of a Piezometer tube is in (A) N/mm2 (B) N/m2 (C) Head of liquid (D) All of these

Description : The pressure measured with the help of a Piezometer tube is in (A) N/mm2 (B) N/m2 (C) Head of liquid (D) All of these

Last Answer : Answer: Option C

The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Last Answer : (b) 17.5 N/mm2

I kgf/cm2 is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) l00 mm Hg.

Description : I kgf/cm2 is equal to  (a) 760 mm Hg  (b) zero mm Hg  (c) 735.6 mm Hg  (d) 1 mm Hg  (e) l00 mm Hg.

Last Answer : Answer : c

For maximum discharge through a chimney, its height should be (A) 200 meters (B) Infinitely long (C) More than 105.7 metres (D) Equal to the height of the hot gas column producing draught

Description : For maximum discharge through a chimney, its height should be (A) 200 meters (B) Infinitely long (C) More than 105.7 metres (D) Equal to the height of the hot gas column producing draught

Last Answer : (D) Equal to the height of the hot gas column producing draught

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

A pressure of 10 m head of water is equivalent to __________ kN/m2 . (A) 98 (B) 147 (C) 196 (D) 49

Description : A pressure of 10 m head of water is equivalent to __________ kN/m2 . (A) 98 (B) 147 (C) 196 (D) 49

Last Answer : (A) 98

The unit of viscosity is (A) N/mm2 (B) N-mm (C) N-s/mm2

Description : The unit of viscosity is (A) N/mm2 (B) N-mm (C) N-s/mm2

Last Answer : (C) N-s/mm2

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2  MN/mm2  and Poisson's ratio is 0.25, the change in the volume of the bar is:  (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Last Answer : (C) 3.125 cm

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N

Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in  diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive  load to remove the clearance, is  (A) 25 N  (B) 30 N  (C) 35 N  (D) 40 N 

Last Answer : (C) 35 N 

A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Last Answer : Answer: Option D

For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Last Answer : Answer: Option D

Whitworth compressed steel is obtained when molten steel is subjected to a pressure of (A) 5 kg/mm2 (B) 9 kg/mm2 (C) 13 kg/mm2 (D) 15 kg/mm

Description : Whitworth compressed steel is obtained when molten steel is subjected to a pressure of (A) 5 kg/mm2 (B) 9 kg/mm2 (C) 13 kg/mm2 (D) 15 kg/mm

Last Answer : Answer: Option B

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Last Answer : b. 281.25 mm2

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Description : Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Last Answer : (D) 40

The atmospheric pressure at sea level is (A) 103 kN/m2 (B) 10.3 m of water (C) 760 mm of mercury (D) All of these

Description : The atmospheric pressure at sea level is (A) 103 kN/m2 (B) 10.3 m of water (C) 760 mm of mercury (D) All of these

Last Answer : Answer: Option D

Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Description : Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Last Answer : 0.015 mm s-1

The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Description : The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800

Last Answer : (A) 500

Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Description : Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm

Last Answer : (A) 50°C and 3 - 4 kg/cm

Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Description : Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Last Answer : (B) 15-45 Kgf/cm2 & 450-550°C

Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of light distillates (B) Suppress coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Last Answer : (B) Suppress coke formation

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C

Description : Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C

Last Answer : (A) 4 kgf/cm2 & 500°C

A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2is (A) 8.82 (B) 9.81 (C) 10.88 (D) 0.95

Description : A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2is (A) 8.82 (B) 9.81 (C) 10.88 (D) 0.95

Last Answer : (A) 8.82

. One stoke (unit of kinematic viscosity) is equivalent to (A) 1 cm2 /second (B) 1 m2 /second (C) 1 gm/cm. second (D) 1 kg. m/second

Description : . One stoke (unit of kinematic viscosity) is equivalent to (A) 1 cm2 /second (B) 1 m2 /second (C) 1 gm/cm. second (D) 1 kg. m/second

Last Answer : (A) 1 cm2 /second

N. second/m2 is (A) The S.I. unit of dynamic viscosity (B) The S.I. unit of kinematic viscosity (C) Equivalent to one poise (D) Equivalent to one stoke

Description : N. second/m2 is (A) The S.I. unit of dynamic viscosity (B) The S.I. unit of kinematic viscosity (C) Equivalent to one poise (D) Equivalent to one stoke

Last Answer : (A) The S.I. unit of dynamic viscosity

One poise (unit of absolute/dynamic viscosity) is equivalent to one (A) gm/cm2 . sec (B) gm/cm. sec (C) cm2 /sec (D) m2 /sec

Description : One poise (unit of absolute/dynamic viscosity) is equivalent to one (A) gm/cm2 . sec (B) gm/cm. sec (C) cm2 /sec (D) m2 /sec

Last Answer : (B) gm/cm. sec

In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Description : In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Last Answer : (B) Liquid is enriched with high boiler

A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k )  a. 543680 N/m2  b. 543.68 kPa (gauge)  c. Both a & b  d. None of the above

Description : A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k )  a. 543680 N/m2  b. 543.68 kPa (gauge)  c. Both a & b  d. None of the above

Last Answer : Both a & b

What is the capture area of a dipole operated at 75 MHz? A. 4 mm B. 2 m2 C. 2.088 m2 D. 4.088 m2

Description : What is the capture area of a dipole operated at 75 MHz? A. 4 mm B. 2 m2 C. 2.088 m2 D. 4.088 m2

Last Answer : C. 2.088 m2