Description : For high grade instruments the steel preferred to, is (A) Cast steel (B) Bessemer steel (C) Mild steel (D) Whitworth compressed steel
Last Answer : Answer: Option A
Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 ... 6 N/mm2 s = 12 N/mm2 (D) b = 5 N/mm2 s = 10 N/mm
Last Answer : (A) b = 10 N/mm2 s = 20 N/mm
Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm
Last Answer : (C) 955.41 kg/cm2
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm
Last Answer : (B) 0.2275 mm
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2
Last Answer : b. 281.25 mm2
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option
Last Answer : (C) 120 N/mm
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N
Last Answer : (C) 35 N
Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm
Last Answer : Answer: Option D
Description : A clay subjected to pressure in excess to its present over-burden, is said to be (A) Pre-compressed (B) Pre-consolidated (C) Over-consolidated (D) All the above
Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these
Last Answer : (A) - 0.000909 m
Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003
Last Answer : (C) 0.0025
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2
Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm
Last Answer : (D) 5 mm
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )
Last Answer : a) Specific Energy Consumption of Induction Melting Furnace Molten Steel Production from the Induction melting furnace per day = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE = 655864000/107 = 65.586 ToE
Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm
Last Answer : (C) 25 cm
Description : A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The extension in the rod was 1 mm only. If Esteel = 2 × 106 kg/cm2 , the side of the rod, is (A) 1 cm (B) 1.5 cm (C) 2 cm (D) 2.5 cm
Last Answer : (C) 2 cm
Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47
Last Answer : d. 25.47
Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg
Last Answer : (B) 102 kg
Description : The maximum pressure to which cast iron pipes may be subjected to, is (A) 3 kg/cm2 (B) 5 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm
Last Answer : (C) 7 kg/cm
Description : The gaseous form of chlorine gets converted into liquid form when subjected to a pressure of (A) 5 kg/cm2 (B) 6 kg/cm2 (C) 7 kg/cm2 (D) 10 kg/cm
Description : Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal allround pressure (B) If the present effective stress is the ... more than present effective stress, it is called over-consolidated clay (D) All the above
Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm
Last Answer : Answer: Option C
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : The modules of elasticity of steel shall be taken as (a) 100kN/mm2 (b) 200 kN/mm2 (c) 250 kN/mm2 (d) 300 kN/mm2
Last Answer : (b) 200 kN/mm2
Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2
Last Answer : [ A ] 2 x 105 N/mm2
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2
Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm
Last Answer : b. 3.14 mm
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2
Last Answer : [ B ] 11.5 N/mm2
Description : Raw Kerosene has a smoke point of 15 mm. After it is subjected to dearomatization by liquid SO2 extraction (Edeleanu process), its smoke point may become __________ mm. (A) 5 (B) 10 (C) 25 (D) 100
Last Answer : (C) 25
Description : A shaft 9 m long is subjected to a torque 30 t-m at a point 3 m distant from either end. The reactive torque at the nearer end will be (A) 5 tonnes metre (B) 10 tonnes metre (C) 15 tonnes metre (D) 20 tonnes metre
Last Answer : (D) 20 tonnes metre
Description : The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 mm
Last Answer : Answer: Option B
Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque
Last Answer : B. Tension