Description : Pick out the wrong statement. (A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1 (B) For calculating forces and ... Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
Last Answer : Option B
Description : The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight
Last Answer : Option A
Description : The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm
Last Answer : c) 21.5 mm*
Description : According to Unwin's formula, the diameter of a rivet of plate of thickness is : (A) d = 6.05 t (B) d = 1.5 t + 4 (C) d = t (D) d = t + 1.5
Last Answer : (A) d = 6.05 t
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm
Last Answer : Answer: Option C
Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm
Last Answer : b. 3.14 mm
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : In the method of tube boring of soil investigation, the following is essential: (A) A tube of about 2 metres length and 20 cm diameter with a cutting edge (B) A flap valve at the bottom of tube is ... and lowered by 4 thick rope moving over a pulley suspended on a tripod stand (D) All the above
Last Answer : Answer: Option D
Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter
Last Answer : (b) 8 mm diameter
Description : Failure of riveted joints is due to (A) Tearing of the plates between the rivet hole and the edge of the plate (B) Tearing of plates between rivets (C) Shearing of rivets (D) All the above
Last Answer : (D) All the above
Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30
Last Answer : (B) 25
Description : The length of the countersunk head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above
Last Answer : a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof *
Description : he length of the snap head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above
Last Answer : a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof *
Description : A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa
Last Answer : (B) 20 KPa
Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2
Last Answer : b) 1.5 kg/cm2
Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N
Last Answer : (C) 35 N
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Last Answer : Answer: Option A
Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm
Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm
Last Answer : [ C ] 40 mm
Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns
Last Answer : a. 10 turns
Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014
Last Answer : (B) 0.30
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45
Description : The maximum permissible differential settlement, in case of foundations in clayey soil, is usually limited to (A) 10 mm (B) 20 mm (C) 30 mm (D) 40 mm
Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75
Last Answer : (b) 15, 25, 40 and 75
Description : __________ is used for producing a thick suspension from a thin slurry. (A) Cartridge filter (B) Rotary drum vacuum filter (C) Pressure filter thickener (D) Plate and frame filter press
Last Answer : (C) Pressure filter thickener
Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time
Last Answer : Answer: Option B
Description : Expansion Joints in masonry walls are provided in wall lengths usater than (A) 10 m (B) 20 m (C) 30 m (D) 40 m
Description : Expansion joints in masonry walls are provided if length exceeds (A) 10 m (B) 20 m (C) 30 m (D) 40 m
Description : The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm
Last Answer : [ B ] 50 mm
Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times
Last Answer : a. increased by 8 times
Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm
Description : high pressure boiler generates steam at a pressure greater than __________ kg/cm2. (A) 10 (B) 30 (C) 50 (D) 80
Last Answer : Option D
Description : Boiler draught of 10 mm water column is equivalent to (A) 1 kgf/m2 (B) 10 kgf/m2 (C) 10 kgf/mm2 (D) 1 kgf/mm2
Last Answer : (B) 10 kgf/m2
Description : What is the co-efficient of contraction, if a fluid jet discharging from a 50 mm diameter orifice has a 40 mm diameter at its vena-contracta? (A) 0.64 (B) 1.65 (C) 0.32 (D) 0.94
Last Answer : (A) 0.64
Description : For achieving rapid drying rate in a spray dryer, the diameter of the particles in the feed should be in the range of __________ microns (1 mm = 1000 microns). (A) 1-5 (B) 10-60 (C) 200-300
Last Answer : (B) 10-60
Description : Correction for capillary effect in manometers (used for pressure measurement) need not be applied, if diameter of the manometer tube is __________ mm. (A) < 4 (B) > 4 (C) > 12.5 (D) < 10
Last Answer : (C) > 12.5
Description : The spacing of bars for perforations in coarse screens used for the treatment of sewage, is A. 20 mm B. 30 mm C. 40 mm D. 50 mm
Last Answer : ANS: D
Description : The peak of a 4 hour flood hydrograph is 240 m3 /sec. If the rainfall excess is 80 mm and base flow which is constant is 40 m3 /sec, peak of 4hours unit hydrograph will be (A) 20 m3 /sec (B) 25 m3 /sec (C) 30 m3 /sec (D) 35 m3 /sec
Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm
Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four
Description : A T-section beam having flange 180mm wide and 20 mm thick and web 150 mm long and 20 mm thick carries a udl of 80 kN/m over an effective span of 8 m. Calculate the maximum bending stress.
Last Answer : Solution :
Description : Alcohol content in freshly prepared natural and fortified wine may be respectively around __________ percent. (A) 7-14 and 14-30 (B) 7-14 and 40-50 (C) 14 - 30 and 40-50 (D) 10 - 20 and 40 - 50
Last Answer : (A) 7-14 and 14-30
Description : Cost of instrumentation in a modern chemical plant ranges from __________ percent of the total plant cost. (A) 5 to 10 (B) 20 to 30 (C) 40 to 50 (D) 60 to 70
Last Answer : (B) 20 to 30
Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)
Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)
Description : Minimum packing space provided between two sleepers, is between A. 20 to 25 cm B. 25 to 30 cm C. 30 to 35 cm D. 35 to 40 cm
Last Answer : C [30 to 35 cm]
Description : Standard disc Plough consists of steel disc of _ diameter a) 20 to 40 cm. c) 60 to 90 cm b) 30 to 60 cm. d) 70 to 100 cm
Last Answer : 60 to 90 cm
Description : Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent. (A) 1 (B) 10 (C) 30 (D) 50
Last Answer : (B) 10