A fully saturated soil is said to be
(A) One phase system
(B) Two phase system with soil and air
(C) Two phase system with soil and water
(D) Three phase system

1 Answer

Answer :

(C) Two phase system with soil and water

Related questions

Description : the water content of a fully saturated soil mass is 100%, then the voids ratio of the sample is (A) Less than specific gravity of soil (B) Equal to specific gravity of soil (C) Greater than specific gravity of soil (D) Independent of specific gravity of soil

Last Answer : Answer: Option B

Description : Pressure exerted by fully saturated air, is known (A) Partial pressure (B) Saturation pressure (C) Saturation vapour pressure (D) Both (c) and (d) of the above

Last Answer : Answer: Option D

Description : A partially saturated soil is classified as (A) One phase soil (B) Two phase soil (C) Three phase soil (D) Four phase soil

Last Answer : (C) Three phase soil

Description : At the liquid limit a) The soil just begins to crumble when rolled into a thread b) The shearing strength against flowing is negligible c) The shearing strength against flowing is a small but definite* d) The soil will not get fully saturated

Last Answer : c) The shearing strength against flowing is a small but definite

Description : The vane shear test is used for the in-situ determination of the undrained strength of the intact fully saturated (A) Sands (B) Clays (C) Gravels (D) Highly organic soils

Last Answer : (B) Clays

Description : Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of ... of vapours which could be contained at the same temperature when fully saturated (D) All the above

Last Answer : Answer: Option D

Description : Pick up the correct statement from the following: (A) Bulking of sand is caused due to formation of a thin film of surface moisture (B) Fine sand bulks more than coarse sand (C) The volume of fully saturated sand, is equal to the volume of dry and loose sand (D) All the above

Last Answer : Answer: Option D

Description : Unconfined compression test it most suitable for determining the : 1. Sensitivity of clays 2. Settlement of embankments 3. ‘Strength’ of partially saturated clay sample 4. ‘Strength’ of fully saturated clay sample (a) 1, 2, 3 and 4 (b) 2 and 3 only (c) 3 and 4 only (d) 1 and 4 only

Last Answer : (d) 1 and 4 only

Description : Which one of the following statements is correct? (a) Adding 5% to 6% of moisture by weight increases the volume of dry sand from 18% to 38% (b) The bulking of fine sand is more than that of coarse sand (c ) Volume of fully saturated sand is equal to that of dry sand (d) All of the above

Last Answer : (d) All of the above

Description : When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the (A) Partial pressure of water vapour is less than the total pressure (B) Humidity is < 100% & dew ... Dew point temperature of air has not reached & air is not saturated fully (D) Air is fully saturated

Last Answer : (D) Air is fully saturated

Description : When the air is fully saturated what is reached'?

Last Answer : dew point

Description : Draw three phase diagram for partially saturated soil. 

Last Answer : Figure : Three Phase Diagram for Partially Saturated Soil 

Description : Pick up the correct statement from the following: (A) The void space between the soil grains, is filled partly with air and partly with water (B) In perfectly saturated soil, the voids are completely filled with water (C) In dry soil, the voids are completely filled with air (D) All the above

Last Answer : Answer: Option D

Description : If the degree of saturation of a partially saturated soil is 60%, then air content of the soil is (A) 40 % (B) 60 % (C) 80 % (D) 100 %

Last Answer : (A) 40 %

Description : If the voids of a soil mass are full of air only, the soil is termed as (A) Air entrained soil (B) Partially saturated soil (C) Dry soil (D) Dehydrated soil

Last Answer : Option C

Description : When the degree of saturation is zero, the soil mass under consideration represents (A) One phase system (B) Two phase system with soil and air (C) Two phase system with soil and water (D) Three phase system

Last Answer : Answer: Option B

Description : Air is said to be saturated when - (1) it contains maximum content of water vapour (2) its pressure is minimum (3) its thickness is maximum (4) it blows over the barren land

Last Answer : (1) it contains maximum content of water vapour Explanation: When a volume of air at a given temperature holds the maximum amount of water vapour, the air is said to be saturated. Mr is said ... 100 percent or is saturated, moisture will condense, mean-ing the water vapor changes to liquid vapor.

Description : Air is said to be saturated when : (1) it contains maximum content of water vapour (2) its pressure is minimum (3) its thickness is maximum (4) it blows over the barren land

Last Answer :  it contains maximum content of water vapour

Description : Which of the following statement(s) is/are true concerning O2 venous saturation monitoring? a. The normal saturation of mixed venous blood is 50% b. Mixed venous blood obtained ... than fully saturated blood, the difference between arterial and venous saturation corresponds to oxygen extraction

Last Answer : Answer: c, d The relationship between oxygen delivery and oxygen consumption is reflected in the amount of oxygen in venous blood. Under normal circumstances, oxygen delivery is 1000 ... and venous saturation corresponds to the oxygen extraction, hence the oxygen delivery/oxygen consumption ratio

Description : Oils are partially hydrogenated (not fully) to manufacture Vanaspati, because fully saturated solidified oils (A) Cause cholesterol build up and blood clotting (B) Are prone to rancid oxidation (C ... (as their complete removal is very difficult) (D) Have affinity to retain harmful sulphur compounds

Last Answer : (A) Cause cholesterol build up and blood clotting

Description : In clay soils, the fields often have to be fully saturated tillage can be undertaken. A. Before. C) After B. Beginning. D) Middle

Last Answer : Before

Description : [53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Last Answer : B. Flux produced is a small fraction of the normal flux

Description : Pick up the correct statement from the following:  (A) The volume of underground water extracted by gravity drainage from a saturated soil, is  known as yield  (B) The ratio of volume ... ) The sum of specific yield and specific retention, is equal to porosity  (D) All the above

Last Answer : (D) All the above

Description : A sample of saturated soil has 30% water content and the specific gravity of soil grains is 2.6. The dry density of the soil mass in g/cm3 , is (A) 1.47 (B) 1.82 (C) 1.91 (D) None of these

Last Answer : (D) None of these

Description : A saturated soil sample has water content of 40% and specific gravity of soil particles 2.7. The void ratio of the soil, is (A) 0.4 (B) 0.52 (C) 1.08 (D) None of these

Last Answer : (C) 1.08

Description : Pick up the correct statement from the following: (A) The phenomenon of quicksand generally occurs in the cohesionless soil (B) At critical hydraulic gradient, the saturated sand becomes quick (C) The critical gradient depends on the void ratio and the specific gravity (D) All the above

Last Answer : (D) All the above

Description : A partially saturated sample of soil has a unit weight of 2.0 g/cm3 and specific gravity of soil particles is 2.6. If the moisture content in the soil is 20%, the degree of saturation is (A) 20 % (B) 77 % (C) 92 % (D) None of these

Last Answer : Answer: Option C

Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Last Answer : Answer: Option B

Description : Sensitivity of a soil can be defined as (A) Percentage of volume change of soil under saturated condition (B) Ratio of compressive strength of unconfined undisturbed soil to that of soil in a remoulded state (C) Ratio of volume of voids to volume of solids (D) None of the above

Last Answer : Answer: Option B

Description : Skempton's pore pressure coefficient B for saturated soil is (A) 1 (B) Zero (C) Between 0 and 1 (D) Greater than 1

Last Answer : Answer: Option A

Description : The main factor which affects the infiltration capacity, is (A) Thickness of saturated layer (B) Depth of surface detention (C) Soil moisture (D) All the above

Last Answer : Answer: Option D

Description : Consider the following statements: 1. For a saturated soil, Skempton's B-parameter is nearly equal to unity. 2. For an undisturbed sensitive clay, the stress-strain curve shows a peak. 3. Interlocking contributes significantly to the shearing ... 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (a) 1, 2 & 3

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

Description : The ratio of the difference between the void ratio of the soil in its loosest state and its natural void ratio (e) to the difference between the void ratios in the loosest and fully dense state, is generally termed as (A) Degree of density (B) Relativity (C) Density index (D) All the above

Last Answer : Answer: Option D

Description : A soil not fully consolidated under the existing over-burden pressure, is called (A) Pre-consolidated (B) Normally consolidated (C) Over-consolidated (D) None of these

Last Answer : Answer: Option C

Description : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

Last Answer : A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is 68.73 A

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

Description : When dew point la reached it is said that at that temperature (a) the atmosphere is said to be saturated with water vapour (b) the relative humidity of the atmosphere is 100% (c) the atmosphere can hold no more water vapour (d) All the above

Last Answer : Ans: (a)

Description : When water exists in the liquid phase and is not about to vaporize, it is considered as _____liquid.  A. Saturated  B. Compressed or subcooled  C. Superheated  D. Unsaturated

Last Answer : Compressed or subcooled

Description : The dew point of a saturated gas phase equals the __________ temperature. (A) Gas (B) Room (C) Wet bulb (D) None of these

Last Answer : (A) Gas

Description : _________________ is the name given to a gaseous phase that is in contact with the liquid phase, or that is in the vicinity of a state where some of it might be condensed.  a) Vapor  b) Saturated Vapor  c) Superheated Vapor  d) Wet Vapor

Last Answer : Vapor

Description : In case of water logged lands a. The soil ports are saturated within a depth of 1 m b. The soil ports are situated within a depth of 60 cm c. The soil ports are situated within a depth of 40 cm b. D.The soil ports are saturated up to the root zone of the crop

Last Answer : D.The soil ports are saturated up to the root zone of the crop

Description : Assertion : During follicular phase , the primary follicles in the ovary grow to become a fully mature Graafian follicle . Reason : Endometrium of ute

Last Answer : Assertion : During follicular phase , the primary follicles in the ovary grow to become a fully mature ... D. If both Assertion & Reason are False.

Description : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A ... thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

Last Answer : A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the ... the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of 125o

Description : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input ... 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

Last Answer : A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high ... (IDF) and the input power factor (IPF) of the converter will be IDF IPF = = 0.5; 0.478

Description : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

Description : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

Last Answer : A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be 0.78

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

Description : If the natural water content of soil mass lies between its liquid limit and plastic limit, the soil mass is said to be in (A) Liquid state (B) Plastic state (C) Semisolid state (D) Solid state

Last Answer : Answer: Option B