The ultimate Settlement of a soil is directly proportional to: (A) Depth of the compressible soil strata (B) Compressive index (C) Both (a) and (b) (D) None of these

The ultimate Settlement of a soil is directly proportional to:
(A) Depth of the compressible soil strata
(B) Compressive index
(C) Both (a) and (b)
(D) None of these
by

1 Answer

Answer :

(D) None of these
by

Related questions

The ultimate consolidation settlement of a soil is (A) Directly proportional to the voids ratio (B) Directly proportional to the compression index (C) Inversely proportional to the compression index (D) None of the above

Description : The ultimate consolidation settlement of a soil is (A) Directly proportional to the voids ratio (B) Directly proportional to the compression index (C) Inversely proportional to the compression index (D) None of the above

Last Answer : (B) Directly proportional to the compression index

Pick up the correct statement from the following: (A) A pile is a slender member which transfers the load through its lower end on a strong strata (B) A pile is a slender member which transfers its load to the surrounding soil (C) A pile is a slender member which transfers its load by friction (D) A pile is a cylindrical body of concrete which transfers the load at a depth greater than its width

Description : Pick up the correct statement from the following: (A) A pile is a slender member which transfers the load through its lower end on a strong strata (B) A pile is a slender member which ... A pile is a cylindrical body of concrete which transfers the load at a depth greater than its width

Last Answer : Answer: Option B

During percussion drilling (A) Ground water observations are hindered due to entry of the slurry in the soil below the bottom of the hole (B) Caving or mixing of strata are caused in soft soils or cohesionless soils (C) The soil to a considerable depth below the bottom of the hole gets disturbed (D) All the above

Description : During percussion drilling (A) Ground water observations are hindered due to entry of the slurry in the soil below the bottom of the hole (B) Caving or mixing of strata are caused in soft soils or ... The soil to a considerable depth below the bottom of the hole gets disturbed (D) All the above

Last Answer : Answer: Option D

Allowable bearing pressure for a foundation depends upon (A) Allowable settlement only (B) Ultimate bearing capacity of soil only (C) Both allowable settlement and ultimate bearing capacity (D) None of above

Description : Allowable bearing pressure for a foundation depends upon (A) Allowable settlement only (B) Ultimate bearing capacity of soil only (C) Both allowable settlement and ultimate bearing capacity (D) None of above

Last Answer : (C) Both allowable settlement and ultimate bearing capacity

According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Description : According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Last Answer : Answer: Option C

The ultimate consolidation settlement of a structure resting on a soil (A) Decreases with the increase in the initial voids ratio (B) Decreases with the decrease in the plastic limit (C) Increases with the increase in the initial voids ratio (D) Increases with the decrease in the porosity of the soil

Description : The ultimate consolidation settlement of a structure resting on a soil (A) Decreases with the increase in the initial voids ratio (B) Decreases with the decrease in the plastic limit (C) Increases ... increase in the initial voids ratio (D) Increases with the decrease in the porosity of the soil

Last Answer : Answer: Option A

Pick up the incorrect statement from the following: (A) Free surface ground water is subjected to atmospheric pressure (B) Water table surface rises and falls with seasons (C) Depth of water table is directly proportional to the rate of drawl of water (D) Level of water table remains stationary

Description : Pick up the incorrect statement from the following:  (A) Free surface ground water is subjected to atmospheric pressure  (B) Water table surface rises and falls with seasons  (C) ... directly proportional to the rate of drawl of water  (D) Level of water table remains stationary 

Last Answer : (D) Level of water table remains stationary 

The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Description : The deflection of any rectangular beam simply supported, is (A) Directly proportional to its weight (B) Inversely proportional to its width (C) Inversely proportional to the cube of its depth (D) Directly proportional to the cube of its length

Last Answer : (C) Inversely proportional to the cube of its depth

The intensity of pressure at any point, in a liquid, is (A) Directly proportional to the area of the vessel containing liquid (B) Directly proportional to the depth of liquid from the surface (C) Directly proportional to the length of the vessel containing liquid (D) Inversely proportional to the depth of liquid from the surface

Description : The intensity of pressure at any point, in a liquid, is (A) Directly proportional to the area of the vessel containing liquid (B) Directly proportional to the depth of liquid from the ... length of the vessel containing liquid (D) Inversely proportional to the depth of liquid from the surface

Last Answer : Answer: Option B

The intensity of pressure at any point, in a liquid, is __________ to the depth of liquid from the surface. (A) Equal (B) Directly proportional (C) Inversely proportional (D) None of these

Description : The intensity of pressure at any point, in a liquid, is __________ to the depth of liquid from the surface. (A) Equal (B) Directly proportional (C) Inversely proportional (D) None of these

Last Answer : Answer: Option B

The ratio of settlement at any time 't' to the final settlement, is known as (A) Co-efficient of consolidation (B) Degree of consolidation (C) Consolidation index (D) Consolidation of undisturbed soil

Description : The ratio of settlement at any time 't' to the final settlement, is known as (A) Co-efficient of consolidation (B) Degree of consolidation (C) Consolidation index (D) Consolidation of undisturbed soil

Last Answer : (B) Degree of consolidation

A soil strata may consist of (A) Soil zone (B) Intermediate zone (C) Capillary zone (D) All the above

Description : A soil strata may consist of (A) Soil zone (B) Intermediate zone (C) Capillary zone (D) All the above

Last Answer : Answer: Option D

Negative skin friction (A) Is a downward drag acting on a pile due to downward movement of the surrounding compressible soil relative to the pile (B) Develops due to lowering of ground water (C) Both (a) and (b) (D) Neither (a) not (b)

Description : Negative skin friction (A) Is a downward drag acting on a pile due to downward movement of the surrounding compressible soil relative to the pile (B) Develops due to lowering of ground water (C) Both (a) and (b) (D) Neither (a) not (b)

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) The bearing capacity of a pile is defined as the load which can be sustained by the pile without producing excessive settlement (B) The safe bearing capacity of a pile is obtained by dividing the ultimate bearing capacity with a suitable factor of safety (C) The factor of safety for piles is taken as 6 (D) All the above

Description : Pick up the correct statement from the following: (A) The bearing capacity of a pile is defined as the load which can be sustained by the pile without producing excessive settlement (B) The safe bearing capacity ... of safety (C) The factor of safety for piles is taken as 6 (D) All the above

Last Answer : Answer: Option D

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower  than the ultimate stress of the material. This property of metal, is called  (A) Plasticity of the ... ) Elasticity of the metal  (C) Fatigue of the metal  (D) Workability of the metal

Last Answer : (C) Fatigue of the metal

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

he lateral earth pressure on a retaining wall (A) Is equal to mass of the soil retained (B) Proportional to the depth of the soil (C) Proportional to the square of the depth of the soil (D) Proportional to the internal friction of the soil

Description : he lateral earth pressure on a retaining wall (A) Is equal to mass of the soil retained (B) Proportional to the depth of the soil (C) Proportional to the square of the depth of the soil (D) Proportional to the internal friction of the soil

Last Answer : (D) Proportional to the internal friction of the soil

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Time factor for a clay layer is (A) A dimensional parameter (B) Directly proportional to permeability of soil (C) Inversely proportional to drainage path (D) Independent of thickness of clay layer

Description : Time factor for a clay layer is (A) A dimensional parameter (B) Directly proportional to permeability of soil (C) Inversely proportional to drainage path (D) Independent of thickness of clay layer

Last Answer : (B) Directly proportional to permeability of soil

The shear strength of a soil (A) Is directly proportional to the angle of internal friction of the soil (B) Is inversely proportional to the angle of internal friction of the soil (C) Decreases with increase in normal stress (D) Decreases with decrease in normal stress

Description : The shear strength of a soil (A) Is directly proportional to the angle of internal friction of the soil (B) Is inversely proportional to the angle of internal friction of the soil (C) Decreases with increase in normal stress (D) Decreases with decrease in normal stress

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) Compaction has no effect on the structure of a soil (B) Permeability decreases with increase in the dry density of a compacted soil (C) A wet side compacted soil is more compressible than a dry side compacted soil (D) Dry side compaction soils swell more when given access to moisture

Description : Pick up the incorrect statement from the following: (A) Compaction has no effect on the structure of a soil (B) Permeability decreases with increase in the dry density of a compacted soil (C) ... a dry side compacted soil (D) Dry side compaction soils swell more when given access to moisture

Last Answer : (A) Compaction has no effect on the structure of a soil

Pile foundation is generally provided if soil is (A) Compressible (B) Water logged (C) Made up (D) All the above

Description : Pile foundation is generally provided if soil is (A) Compressible (B) Water logged (C) Made up (D) All the above

Last Answer : Answer: Option D

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D

The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of (A) 0.367 xu (B) 0.416 xu (C) 0.446 xu (D) 0.573 xu Where xu is the depth of neutral axis at the limit state of collapse

Description : The centroid of compressive force, from the extreme compression fiber, in limit state design lies at a distance of (A) 0.367 xu (B) 0.416 xu (C) 0.446 xu (D) 0.573 xu Where xu is the depth of neutral axis at the limit state of collapse

Last Answer : Answer: Option B

In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Description : In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Last Answer : (d) 0.360 fck . Xu

The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Last Answer : (b) Breadth

Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Description : Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Last Answer : c. Ultimate stress / Permissible stress

The shear stress between the two liquid layers is __________ proportional to the distance between two layers(A) Directly (B) Inversely (C) Both A and B (D) None of these .

Description : The shear stress between the two liquid layers is __________ proportional to the distance between two layers. (A) Directly (B) Inversely (C) Both A and B (D) None of these

Last Answer : Answer: Option B

The strainer type tube well, is unsuitable for (A) Coarse gravels (B) Fine sandy strata (C) Clean gravels (D) None of these

Description : The strainer type tube well, is unsuitable for (A) Coarse gravels (B) Fine sandy strata (C) Clean gravels (D) None of these

Last Answer : (B) Fine sandy strata

Pick up the correct statement from the following: (A) A confined bed of impervious material laid over an aquifer, is known as an aquiclude (B) The top most water bearing strata having no aquifer, is known as non-artesian aquifer (C) The ordinary gravity wells which supply water from the top most water bearing strata, are called water table wells (D) All the above

Description : Pick up the correct statement from the following: (A) A confined bed of impervious material laid over an aquifer, is known as an aquiclude (B) The top most water bearing strata having no aquifer, is ... water from the top most water bearing strata, are called water table wells (D) All the above

Last Answer : Answer: Option D

In tropical regions, (A) The surface gets heated more effectively than the arctic areas (B) After heating, the air becomes lighter and is displaced by cool air from the polar regions (C) The rising tropical air flows towards the polar region in the upper strata (D) All of the above

Description : In tropical regions, (A) The surface gets heated more effectively than the arctic areas (B) After heating, the air becomes lighter and is displaced by cool air from the polar regions (C) The rising tropical air flows towards the polar region in the upper strata (D) All of the above

Last Answer : (D) All of the above

The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Description : The observed N- value from a standard penetration test conducted in saturated sandy strata is 30; the N- value corrected for dilatancy may be taken as : (b) 15 (a) 20 (c) 23 (d) 39

Last Answer : (c) 23

Water is __________ liquid. (A) A compressible (B) An incompressible (C) Both A and B (D) None of these

Description : Water is __________ liquid. (A) A compressible (B) An incompressible (C) Both A and B (D) None of these

Last Answer : Answer: Option B

Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by the force of adhesion between liquid molecules c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Description : Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by ... it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Last Answer : c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions

The section modulus of a rectangular section is proportional to (A) Area of the section (B) Square of the area of the section (C) Product of the area and depth (D) Product of the area and width

Description : The section modulus of a rectangular section is proportional to  (A) Area of the section  (B) Square of the area of the section  (C) Product of the area and depth  (D) Product of the area and width

Last Answer : (A) Area of the section

In a shaft, the shear stress is not directly proportional to (A) Radius of the shaft (B) Angle of twist (C) Length of the shaft (D) Modulus of rigidity

Description : In a shaft, the shear stress is not directly proportional to  (A) Radius of the shaft  (B) Angle of twist  (C) Length of the shaft  (D) Modulus of rigidity

Last Answer : (C) Length of the shaft

The strain energy due to volumetric strain (A) Is directly proportional to the volume (B) Is directly proportional to the square of exerted pressure (C) Is inversely proportional to Bulk modulus (D) All the above

Description : The strain energy due to volumetric strain  (A) Is directly proportional to the volume  (B) Is directly proportional to the square of exerted pressure  (C) Is inversely proportional to Bulk modulus  (D) All the above 

Last Answer : (D) All the above 

Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly proportional to (A) Modulus of rigidity (B) Angle of twist (C) Reciprocal of the length of the shaft (D) Moment of inertia of the shaft section

Description : Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly  proportional to  (A) Modulus of rigidity  (B) Angle of twist  (C) Reciprocal of the length of the shaft  (D) Moment of inertia of the shaft section 

Last Answer : (D) Moment of inertia of the shaft section 

Contour interval is (A) Inversely proportional to the scale of the map (B) Directly proportional to the flatness of ground (C) Larger for accurate works (D) Larger if the time available is more

Description : Contour interval is (A) Inversely proportional to the scale of the map (B) Directly proportional to the flatness of ground (C) Larger for accurate works (D) Larger if the time available is more

Last Answer : (A) Inversely proportional to the scale of the map

Hooke's law states that stress and strain are (A) Directly proportional (B) Inversely proportional (C) Curvilinearly related (D) None of these

Description : Hooke's law states that stress and strain are (A) Directly proportional (B) Inversely proportional (C) Curvilinearly related (D) None of these

Last Answer : (A) Directly proportional

Stress in a beam due to simple bending, is (A) Directly proportional (B) Inversely proportional (C) Curvilinearly related (D) None of these

Description : Stress in a beam due to simple bending, is  (A) Directly proportional  (B) Inversely proportional  (C) Curvilinearly related  (D) None of these 

Last Answer : (A) Directly proportional 

In a shaft shear stress intensity at a point is not (A) Directly proportional to the distance from the axis (B) Inversely proportional to the distance from the axis (C) Inversely proportional to the polar moment of inertia (D) Directly proportional to the applied torque

Description : In a shaft shear stress intensity at a point is not (A) Directly proportional to the distance from the axis (B) Inversely proportional to the distance from the axis (C) Inversely proportional to the polar moment of inertia (D) Directly proportional to the applied torque

Last Answer : (B) Inversely proportional to the distance from the axis

The critical exist gradient of seepage water in soils, is (A) Directly proportional to the voids ratio (B) Inversely proportional to the specific gravity (C) Directly proportional to the specific gravity (D) None of these

Description : The critical exist gradient of seepage water in soils, is (A) Directly proportional to the voids ratio (B) Inversely proportional to the specific gravity (C) Directly proportional to the specific gravity (D) None of these

Last Answer : (D) None of these

The total active earth pressure due to dry back fill with no surcharge, acts at H/3 above the base of the wall and is directly proportional to (A) H (B) H (C) H 2 (D) H 3

Description : The total active earth pressure due to dry back fill with no surcharge, acts at H/3 above the base of the wall and is directly proportional to (A) H (B) H (C) H 2 (D) H 3

Last Answer : (C) H

Degree of consolidation is (A) Directly proportional to time and inversely proportional to drainage path (B) Directly proportional to time and inversely proportional to square of drainage path (C) Directly proportional to drainage path and inversely proportional to time (D) Directly proportional to square of drainage path and inversely proportional to time

Description : Degree of consolidation is (A) Directly proportional to time and inversely proportional to drainage path (B) Directly proportional to time and inversely proportional to square of drainage path (C ... to time (D) Directly proportional to square of drainage path and inversely proportional to time

Last Answer : Answer: Option B

The coherence length over which there is a strong relationship between amplitudes is; (A) Directly proportional to the bandwidth (B) Inversely proportional to the bandwidth (C) The square of the bandwidth (D) None of these

Description : The coherence length over which there is a strong relationship between amplitudes is; (A) Directly proportional to the bandwidth (B) Inversely proportional to the bandwidth (C) The square of the bandwidth (D) None of these

Last Answer : Answer: Option B

Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section (C) Distance of the C.G. of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Last Answer : Answer: Option D

An open tank containing liquid is moving with an acceleration on an inclined plane. The inclination of the free surface of the liquid will be __________ to the acceleration of the tank. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Description : An open tank containing liquid is moving with an acceleration on an inclined plane. The inclination of the free surface of the liquid will be __________ to the acceleration of the tank. (A) Equal to (B) Directly proportional (C) Inversely proportional (D) None of these

Last Answer : Answer: Option B