A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower 

than the ultimate stress of the material. This property of metal, is called 

(A) Plasticity of the metal 

(B) Elasticity of the metal 

(C) Fatigue of the metal 

(D) Workability of the metal

by

1 Answer

Answer :

(C) Fatigue of the metal

by

Related questions

Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating(B) Tensile(C) Compressive(D) Torsion

Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion

Last Answer : (A) Fluctuating

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleabilityy

Last Answer : (c) Ductility

Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Last Answer : (C) Fluctuating

When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Last Answer : d) Plasticity

A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be three times the maximum tensile stress, centre of gravity of the section from flange side is (A) h/4 (B) h/3 (C) h/2 (D) 2/3 h

Description : A cast iron T section beam is subjected to pure bending. For maximum compressive stress to be  three times the maximum tensile stress, centre of gravity of the section from flange side is  (A) h/4  (B) h/3  (C) h/2  (D) 2/3 h

Last Answer : (A) h/4 

The property of a material by which it can be beaten or rolled into thin plates, is called (A) Malleability (B) Ductility (C) Plasticity (D) Elasticity

Description : The property of a material by which it can be beaten or rolled into thin plates, is called  (A) Malleability  (B) Ductility  (C) Plasticity  (D) Elasticity

Last Answer : (A) Malleability 

The property of a material by which it can be drawn to a smaller section, due to tension, is called (A) Plasticity (B) Ductility (C) Elasticity (D) Malleability

Description : The property of a material by which it can be drawn to a smaller section, due to tension, is called (A) Plasticity (B) Ductility (C) Elasticity (D) Malleability

Last Answer : (B) Ductility

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Description : Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Last Answer : c. Ultimate stress / Permissible stress

The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress

Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress

Last Answer : 3. tensile stress

The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Last Answer : 1. direct tensile stress and bending stress

The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Last Answer : B Bending stress

When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Last Answer : (B) Bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Last Answer : b) tensile stress

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Last Answer : (d) Malleability

The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Description : The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Last Answer : (b) Ductility

During a tensile test on a ductile material (A) Nominal stress at fracture is higher than the ultimate stress (B) True stress at fracture is higher than the ultimate stress (C) True stress at fracture is the same as the ultimate stress (D) None of these

Description : During a tensile test on a ductile material (A) Nominal stress at fracture is higher than the ultimate stress (B) True stress at fracture is higher than the ultimate stress (C) True stress at fracture is the same as the ultimate stress (D) None of these

Last Answer : (B) True stress at fracture is higher than the ultimate stress

The property by which a body returns to its original shape after removal of the force, is called (A) Plasticity (B) Elasticity (C) Ductility (D) Malleability

Description : The property by which a body returns to its original shape after removal of the force, is called  (A) Plasticity  (B) Elasticity  (C) Ductility  (D) Malleability 

Last Answer : (B) Elasticity 

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

A composite beam is composed of two equal strips one of brass and other of steel. If the temperature is raised (A) Steel experiences tensile force (B) Brass experiences compressive force (C) Composite beam gets subjected to a couple (D) All the above

Description : A composite beam is composed of two equal strips one of brass and other of steel. If the  temperature is raised  (A) Steel experiences tensile force  (B) Brass experiences compressive force  (C) Composite beam gets subjected to a couple  (D) All the above

Last Answer : (D) All the above

In a spherical dome subjected to concentrated load at crown or uniformly distributed load, the meridional force is always (A) Zero (B) Tensile (C) Compressive (D) Tensile or compressive

Description : In a spherical dome subjected to concentrated load at crown or uniformly distributed load, the meridional force is always (A) Zero (B) Tensile (C) Compressive (D) Tensile or compressive

Last Answer : (C) Compressive

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Last Answer : (b) Due to tensile

A long vertical member, subjected to an axial compressive load, is called (A) A column (B) A strut (C) A tie (D) A stanchion

Description : A long vertical member, subjected to an axial compressive load, is called (A) A column (B) A strut (C) A tie (D) A stanchion

Last Answer : (A) A column

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

_______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Description : _______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Last Answer : (A) Hardness

The ability of a body to return to its original shape is called: a) Plasticity b) Elasticity c) Strain d) Stress

Description : The ability of a body to return to its original shape is called: a) Plasticity b) Elasticity c) Strain d) Stress

Last Answer : b) Elasticity

Pick up the correct statement from the following: (A) The moment of inertia is calculated about the axis about which bending takes place (B) If tensile stress is less than axial stress, the section experiences compressive stress (C) If tensile stress is equal to axial stress, the section experiences compressive stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The moment of inertia is calculated about the axis about which bending takes place  (B) If tensile stress is less than axial ... tensile stress is equal to axial stress, the section experiences compressive stress  (D) All the above 

Last Answer : (D) All the above 

When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Last Answer : (C) Tensile stress

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress