As compared to uniaxial tension or compression, the strain energy stored in bending is only
(A) 1/8
(B) 1/4
(C) 1/3
(D) 1/2
Description : A metal having a Poisson's ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is (A) -0.8 (B) 0.8 (C) +0.08 (D) -0.24
Last Answer : (D) -0.24
Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending
Last Answer : [ C ] The strain at different points in the section will be same
Description : A column said to be under uniaxial bending, when the eccentricity is [ A ] with respect to one axis only [ B ] with respect to two axes [ C ] zero [ D ] 20 mm
Last Answer : [ A ] with respect to one axis only
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?
Last Answer : 10001/999900
Description : The assumption in the theory of bending of beams is: (A) Material is homogeneous (B) Material is isotropic (C) Young's modulus is same in tension as well as in compression (D) All the above
Last Answer : (D) All the above
Description : Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains ... bending (C) The material of the beam is homogeneous and isotropic (D) All the above
Description : A fire hose has a nozzle attached to it, and the nozzle discharges a jet of water into the atmosphere at a velocity of 20 m/s. this causes the joint of the nozzle with the hose to be in : (a) Tension (b) A state of zero stress (c) Compression (d) Bending stress
Last Answer : (a) Tension
Description : The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension
Last Answer : Option A
Description : Coil springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : (c) compression
Description : Leaf springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : a) bending
Description : Coil springs absorb shocks by (A) bending (B) twisting (C) compression (D) tension
Last Answer : (C) compression
Description : Under sagging bending moment, the uppermost fiber of the beam is in (a) Shear (b) Compression (c) Tension (d) None)
Last Answer : (b) Compression
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE
Last Answer : (D) W²L/2AE
Description : The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load
Last Answer : (B) Proof resilience
Description : In a R.C section under flexure, the assumption that a plane section before bending remains plane after bending leads to (a) Strain distribution being linear across the depth (b) ... strain distribution being linear across the depth (d) Shear stress distribution being uniform along the depth
Last Answer : (a) Strain distribution being linear across the depth
Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.
Last Answer : (b) Only steel bars will resist tension.
Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.
Last Answer : (c) Both concrete & steel will resist tension.
Description : The compression in steel (fS) at failure for Fe - 415 grade steel using stress-strain curve shall be [ A ] 0.87 fy [ B ] 0.75 fy [ C ] 0.45 fy [ D ] 0.55 fy
Last Answer : [ B ] 0.75 fy
Description : The ultimate failure is assumed to be reached when the section reaches a uniform compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.005
Last Answer : [ A ] 0.002
Description : The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006
Last Answer : [ B ] 0.0035
Description : The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola
Last Answer : [ B ] a rectangular parabolic curve
Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above
Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5
Last Answer : (c) 4, 1, 3, 5 and 2
Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None
Last Answer : (c) Strain energy, deflection and strength
Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam
Last Answer : Answer: Option C
Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these
Description : Ratio of permissible stress in direct compression and bending compression is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2.0 (D) Greater than 2
Last Answer : Answer: Option A
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None
Last Answer : (c) Thirdly Maximum Principal stress theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None
Last Answer : (d) None
Description : The force which develops in a pressure conduit supported on trestles, is (A) Tension (B) Compression (C) Temperature stress (D) Flexural stress
Last Answer : (D) Flexural stress
Description : When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would (A) Change from compression to tension (B) Change from tension to compression (C) Always be compression (D) Always be tension
Last Answer : (A) Change from compression to tension
Description : The possible loading in various members of framed structures are (A) Compression or tension (B) Buckling or shear (C) Shear or tension (D) All of the above
Last Answer : (A) Compression or tension
Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension
Last Answer : Answer: Option D
Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above
Description : According to the steel beam theory of doubly reinforced beams (A) Tension is resisted by tension steel (B) Compression is resisted by compression steel (C) Stress in tension steel equals the stress in compression steel (D) All the above
Description : In pre-stressed concrete (A) Forces of tension and compression change but lever arm remains unchanged (B) Forces of tension and compressions remain unchanged but lever arm changes with the moment ( ... arm change (D) Both forces of tension and compression as well as lever arm remain unchanged
Last Answer : Answer: Option B
Description : The average permissible stress in bond for plain bars in tension is (A) Increased by 10% for bars in compression (B) Increased by 25% for bars in compression (C) Decreased by 10% for bars in compression (D) Decreased by 25% for bars in compression
Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates
Last Answer : Option D
Description : Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam
Last Answer : (a) Tension reinforcement in the beam
Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile
Last Answer : (b) Zero at one end and compression at the other end
Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets
Last Answer : (c) Tacking rivets
Description : The equilibrium equation for the condition that tension will be equal to the compression is given by [ A ] Compression in concrete = Tension in steel [ B ] Compression in concrete + Compression in steel = Tension in steel [ C ] Compression in concrete = Compression in steel [ D ] None of the above
Last Answer : [ B ] Compression in concrete + Compression in steel = Tension in steel
Description : Flanged beams are preferred when the concrete in the slab is on the [ A ] compression side of the beam [ B ] tension side of the beam [ C ] may be compression side or tension side of the beam [ D ] none of the above
Last Answer : [ A ] compression side of the beam
Description : Development length is the length or extension that should be provided on either side from the [ A ] face of the support [ B ] point of maximum tension [ C ] point of maximum compression [ D ] point of minimum compression
Last Answer : [ B ] point of maximum tension
Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above
Last Answer : [ B ] 0.87 fy