Description : The frame consists of a steel beam welded rigidly to two vertical channels. An eccentric exciter weighing 250 N is attached to the beam, which weighs 10 KN and is used to excite the frame. The unbalance weight of ... ends, magnification factor at resonance is A. 307.5 B. 3.075 C. 30.75 D. 0.3075
Last Answer : C. 30.75
Description : The staff intercept will be (A) Greater farther off the staff is held (B) Smaller, farther off the staff is held (C) Smaller, nearer the staff is held (D) Same, wherever the staff is held
Last Answer : (B) Smaller, farther off the staff is held
Description : The intercept of a staff (A) Is maximum if the staff is held truly normal to the line of sight (B) Is minimum if the staff is held truly normal to the line of sight (C) Decreases if the staff is tilted away from normal (D) Increases if the staff is tilted towards normal
Last Answer : (B) Is minimum if the staff is held truly normal to the line of sight
Description : Tilt of the staff in stadia tacheometry increases the intercept if it is (A) Away from the telescope pointing down hill (B) Towards the telescope pointing up-hill (C) Away from the telescope pointing up-hill (D) None of these
Last Answer : (C) Away from the telescope pointing up-hill
Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m
Last Answer : (D) 0.060 m
Description : A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant ... inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17
Last Answer : (C) 12°
Description : The staff reading at a distance of 80 m from a level with the bubble at its centre is 1.31 m. When the bubble is moved by 5 divisions out of the centre, the reading is 1.39 m. The angular value of the one division of the bubble, is (A) 28.8 sec (B) 41.25 sec (C) 14.52 sec (D) 25.05
Last Answer : (B) 41.25 sec
Description : The line of sight is kept as high above ground surface as possible to minimise the error in the observed angles due to (A) Shimmering (B) Horizontal refraction (C) Vertical refraction (D) Both shimmering and horizontal refraction
Last Answer : (D) Both shimmering and horizontal refraction
Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm
Last Answer : (B) 75 mm
Description : A district road with a bituminous pavement has a horizontal curve of 1000 m for a design speed of 75 km ph. The super-elevation is (A) 1 in 40 (B) 1 in 50 (C) 1 in 60 (D) 1 in 70
Last Answer : Answer: Option A
Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm
Last Answer : (a) 120 mm
Description : Two observation wells penetrating into a confined aquifer are located 1500 m apart in the direction of flow. Heads of 50 m and 25 m are indicated at these two observation wells. If the coefficient of permeability for the ... well to another is (a) 75 days (b) 750 days (c) 1200 days (d) 3000 days
Last Answer : (b) 750 days
Description : What kind of organizational structure combines a vertical chain of command with horizontal reporting requirements? (a) Line authority ; (b) Matrix ; (c) Functional ; (d) Line-and-staff
Last Answer : (b) Matrix ;
Description : A ______ organizational structure is the simplest form and has clear lines of authority and ease of decision making. (a) Horizontal ; (b) Line ; (c) Vertical ; (d) Staff
Last Answer : (b) Line ;
Description : In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is (A) 5.24 cm (B) 6.24 cm (C) 7.24 cm (D) 8.24 cm
Last Answer : (C) 7.24 cm
Description : Pick up the incorrect statement from the following: (A) Lead is the average horizontal straight distance between the borrow pit and the place of spreading soil (B) The lead is calculated for each block of the ... a distance upto 500 m (D) The unit of lead is 1 km where the lead exceeds 2 km
Last Answer : (D) The unit of lead is 1 km where the lead exceeds 2 km
Description : The horizontal clearance between guard rail and running rail in BG track is a) 25 mm b) 250 ± 50 mm* c) 75 mm d) 200 ± 50 mm
Last Answer : b) 250 ± 50 mm*
Description : The constant vertical distance between two adjacent contours, is called (A) Horizontal interval (B) Horizontal equivalent (C) Vertical equivalent (D) Contour interval
Last Answer : (D) Contour interval
Description : Contour interval is (A) The vertical distance between two consecutive contours (B) The horizontal distance between two consecutive contours (C) The vertical distance between two points on same contour (D) The horizontal distance between two points on same contour
Last Answer : (A) The vertical distance between two consecutive contours
Description : Design of horizontal and vertical alignments, super-elevation, sight distance and grades, is worst affected by (A) Width of the vehicle (B) Length of the vehicle (C) Height of the vehicle (D) Speed of the vehicle
Last Answer : Answer: Option D
Description : A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half left hand span ... A) 10.8 tonnes (B) 1.08 tonnes (C) 1.8 tonnes (D) 0.8 tonnes
Last Answer : (B) 1.08 tonnes
Description : The maximum non-verticality of the bore of a well 200 m deep, may be permitted up to (A) 25 cm (B) 50 cm (C) 75 cm (D) 100 cm
Last Answer : (D) 100 cm
Description : P.V.C. pipes can withstand pressure bead of water upto (A) 25 m (B) 50 m (C) 75 m (D) 100 m
Last Answer : (D) 100 m
Description : The top height of a route marker above crown level is (A) 1.50 m (B) 1.75 m (C) 2.00 m (D) 2.25 m
Description : For a 6.6 m wide two lane pavement, berms are provided on either side having a width of (A) 1.00 m (B) 1.25 m (C) 1.50 m (D) 1.75 m
Last Answer : Answer: Option C
Description : A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at and were 1.22 and 1.06. With the level set up at , the readings at and were 1.55 and ... upwards (B) 0.04 m inclined downwards (C) 0.04 m inclined upward (D) None of these
Last Answer : (B) 0.04 m inclined downwards
Last Answer : The horizontal intercept of dc load line is the same as ideal cut off point.
Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m
Last Answer : (B) 25 m
Description : Can two non vertical parallel lines can have the same y-intercept?
Last Answer : No, they cannot - unless the two lines are effectively the sameline.
Description : For wave action in dams, the maximum height of freeboard is generally taken to be equal to (A) 0.5 hw (B) 0.75 hw (C) 1.25 hw (D) 1.50 hw
Description : A car weighing 1000kg deflects its springs by 0.4cm under its load. Determine the natural frequency of 2 car in vertical direction take g=10N/m a) 25 rad/sec b)50 rad/sec c) 2 rad/sec d)none
Last Answer : b)50 rad/sec
Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m
Last Answer : (C) 45 m
Description : A masonry dam (density = 20,000 N/m3 ) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be (A) 75 N/m2 (B) 750 N/m2 (C) 7500 N/m2 (D) 75000 N/m
Last Answer : (C) 7500 N/m
Description : A balanced three-phase, 50 Hz voltage is applied to a 3 phase, 4 pole, induction motor. When the motor is delivering rated output, the slip is found to be 0.05. The speed of the rotor m.m.f. relative to the rotor structure is (A) 1500 r.p.m. (B) 1425 r.p.m. (C) 25 r.p.m. (D) 75 r.p.m.
Last Answer : (D) 75 r.p.m.
Description : For a tachometer the additive and multiplying constants are respectively (A) 0 and 100 (B) 100 and 0 (C) 0 and 0 (D) 100 and 100
Last Answer : (A) 0 and 100
Description : If +0.8% grade meets -0.7% grade and the rate of change of grade for 30 m distance is 0.05, the length of the vertical curve will be (A) 600 m (B) 700 m (C) 800 m (D) 900 m
Last Answer : (D) 900 m
Description : A coarse-grained soil has a voids ratio 0.75, and specific gravity as 2.75. The critical gradient at which quick sand condition occurs, is (A) 0.25 (B) 0.50 (C) 0.75 (D) 1.00
Last Answer : (D) 1.00
Description : For determine the specific gravity of soil solids, using a pycnometer of 500 cc., the following data is available : Weight of dry empty pycnometer = 125 g Weight of dried soil and pycnometer = 500 g Weight of dried soil and distilled ... of soil solids, is (A) 2.0 (B) 2.25 (C) 2.50 (D) 2.75
Last Answer : (C) 2.50
Description : The maximum shear stress (qmax) in a rectangular beam is (A) 1.25 times the average (B) 1.50 times the average (C) 1.75 times the average (D) 2.0 times the average
Last Answer : Answer: Option B
Description : The ratio of the breadth to effective depth of a beam is kept (A) 0.25 (B) 0.50 (C) 0.70 (D) 0.75
Description : If the sides o a slab simply supported on its edges and spanning in two way are equal, then the maximum bending moment is multiplied by. (a) 0.25 (b) 0.50 (c) 0.75 (d) 0.85
Last Answer : (b) 0.50
Description : The proportion of coarse aggregates to fire aggregates in structural concrete is usually [ A ] 0.50 - 1.25 [ B ] 1.25 - 4.50 [ C ] 1.50 - 2.50 [ D ] 0.25 - 0.75
Last Answer : [ C ] 1.50 - 2.50
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : Two columns 50 cm 50 cm and 60 cm 60 cm carry 80 tonnes and 120 tonnes of loads respectively. The centre to centre distance between columns is 5.00 metres. The permissible bearing capacity of the soil is 20 t ... the foundation slab = 7.00 m (C) Area of footing slab = 11.00 m2 (D) All the above
Last Answer : Option D
Description : Pick up the correct statement from the following: (A) Box sextant is used for the measurement of horizontal angles (B) Cross staff is used for setting out right angles (C) Gradiometer is used for setting out any required gradient (D) All the above
Last Answer : (D) All the above
Description : Pick up the correct statement from the following: (A) The lines of sight while observing back sight and fore sight lie in the same horizontal plane (B) The staff readings are measurements made ... readings are taken, coincides with the level surface through the telescope axis (D) All the above
Description : Extra widening required at a horizontal curve on a single lane hill road of radius 80 m for a design speed of 50 km ph and for a vehicle with wheel base 6.0 m is (A) 0.225 m (B) 0.589 m (C) 1.250 m (D) None of these
Description : The total value of extra widening required at a horizontal curve on a two lane hill road of radius 42 m for a design speed of 50 kmph and for vehicles with wheel base 6 m, is (A) 0.500 m (B) 0.589 m (C) 1.089 m (D) 0.089 m
Description : The minimum distance between the centres of bulb of diameter du, of a multi under reamed piles, is (A) du (B) 1.25 du (C) 1.5 du (D) 1.75 du
Description : In tangential tacheometry, an ordinary level staff is used (A) Leaning towards the instrument for inclined sights upward (B) Leaning away from the instrument for inclined sights downwards (C) Vertical in all cases (D) None of these
Last Answer : (C) Vertical in all cases