A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at and were 1.22 and 1.06. With the level set up at , the readings at and were 1.55 and 1.37. The collimation error per 100 m length of sight is (A) 0.02 m inclined upwards (B) 0.04 m inclined downwards (C) 0.04 m inclined upward (D) None of these

A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff 

readings at and were 1.22 and 1.06. With the level set up at , the readings at 

and were 1.55 and 1.37. The collimation error per 100 m length of sight is 

(A) 0.02 m inclined upwards 

(B) 0.04 m inclined downwards 

(C) 0.04 m inclined upward 

(D) None of these

by

1 Answer

Answer :

(B) 0.04 m inclined downwards 

by

Related questions

A dumpy level was set up at mid-point between pegs A and B, 80 m apart and the staff readings were 1.32 and 1.56. When the level was set up at a point 10 m from A on BA produced, the staff readings obtained at A and B were 1.11 and 1.39. The correct staff reading from this set up at S should be (A) 1.435 (B) 1.345 (C) 1.425 (D) None of these

Description : A dumpy level was set up at mid-point between pegs A and B, 80 m apart and the staff readings were 1.32 and 1.56. When the level was set up at a point 10 m from A on BA produced, the staff readings obtained at A ... this set up at S should be (A) 1.435 (B) 1.345 (C) 1.425 (D) None of these

Last Answer : (B) 1.345

A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m and 284.295 m respectively, the collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Last Answer : (D) 0.060 m

Which one of the following statements is not correc t? (a) Parallax error is eliminated when there is no change in the staff reading when eye is moved up and down (b) The objective lens is to be focused towards a white or bright background for clear visibility of cross-hairs (c) Temporary adjustments of the dumpy level are to be performed at every set up (d) The eyepiece need not be adjusted after the first set up when the same surveyor is taking readings

Description : Which one of the following statements is not correc t? (a) Parallax error is eliminated when there is no change in the staff reading when eye is moved up and down (b) The objective lens is ... (d) The eyepiece need not be adjusted after the first set up when the same surveyor is taking readings

Last Answer : (b) The objective lens is to be focused towards a white or bright background for clear visibility of cross-hairs

Pick up the correct statement from the following: (A) The lines of sight while observing back sight and fore sight lie in the same horizontal plane (B) The staff readings are measurements made vertically downwards from a horizontal plane (C) The horizontal plane with reference to which staff readings are taken, coincides with the level surface through the telescope axis (D) All the above

Description : Pick up the correct statement from the following: (A) The lines of sight while observing back sight and fore sight lie in the same horizontal plane (B) The staff readings are measurements made ... readings are taken, coincides with the level surface through the telescope axis (D) All the above

Last Answer : (D) All the above

In tangential tacheometry, an ordinary level staff is used (A) Leaning towards the instrument for inclined sights upward (B) Leaning away from the instrument for inclined sights downwards (C) Vertical in all cases (D) None of these

Description : In tangential tacheometry, an ordinary level staff is used (A) Leaning towards the instrument for inclined sights upward (B) Leaning away from the instrument for inclined sights downwards (C) Vertical in all cases (D) None of these

Last Answer : (C) Vertical in all cases

Staff readings on pegs x and y from X station are 1.755 m and 2.850 m, and from station Y on staff head at Y and X are 0.655 m and 1.560 m. If reduced level of X is 105.5 m, the reduced level of Y is (A) 104.0 m (B) 104.5 m (C) 105.0 m (D) 105.5 m

Description : Staff readings on pegs x and y from X station are 1.755 m and 2.850 m, and from station Y on staff head at Y and X are 0.655 m and 1.560 m. If reduced level of X is 105.5 m, the reduced level of Y is (A) 104.0 m (B) 104.5 m (C) 105.0 m (D) 105.5 m

Last Answer : (B) 104.5 m

The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to (A) The distance between the zero of gradient and the foot of the staff (B) Twice the distance between the zero of graduation and the foot of the staff (C) Thrice the distance between the zero of graduation and the foot of the staff (D) None of the above

Description : The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to (A) The distance between the zero of ... Thrice the distance between the zero of graduation and the foot of the staff (D) None of the above

Last Answer : (B) Twice the distance between the zero of graduation and the foot of the staff

In order to measure the flow with a Venturimeter, it is installed in (A) Horizontal line (B) Inclined line with flow upwards (C) Inclined line with flow downwards (D) Any direction and in any location

Description : In order to measure the flow with a Venturimeter, it is installed in (A) Horizontal line (B) Inclined line with flow upwards (C) Inclined line with flow downwards (D) Any direction and in any location

Last Answer : Answer: Option D

Normally the isoquant slopes (a) downwards from left to right (b) upward from right to left © upwards from left to right (d) backwards from left to right

Description : Normally the isoquant slopes (a) downwards from left to right (b) upward from right to left © upwards from left to right (d) backwards from left to right

Last Answer : (a) downwards from left to right

Calculate the dipole moment of a dipole with equal charges 2C and -2C separated by a distance of 2cm. a) 0.02 b) 0.04 c) 0.06 d) 0.08

Description : Calculate the dipole moment of a dipole with equal charges 2C and -2C separated by a distance of 2cm. a) 0.02 b) 0.04 c) 0.06 d) 0.08

Last Answer : b) 0.04

The alcoholic content of **** is approximately _____. a. 0.02 b. 0.04 c. 0.06 d. 0.08

Description : The alcoholic content of beer is approximately _____. a. 0.02 b. 0.04 c. 0.06 d. 0.08

Last Answer : b. 0.04

If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Description : If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for (A) Horizontal sights (B) Inclined sights upward (C) Inclined sight downward (D) None of these

Last Answer : (A) Horizontal sights

Dumpy level is most suitable when (A) The instrument is to be shifted frequently (B) Fly levelling is being done over long distance (C) Many readings are to be taken from a single setting of the instrument (D) All of the above

Description : Dumpy level is most suitable when (A) The instrument is to be shifted frequently (B) Fly levelling is being done over long distance (C) Many readings are to be taken from a single setting of the instrument (D) All of the above

Last Answer : (C) Many readings are to be taken from a single setting of the instrument

In which case power required would be more a.In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec b.In lowering a weight of 100 kg along an a inclined plane at an angle of 45? with c.In lifting up a weight of 100 kg at a constant speed of 3 m/sec d.In lowering the weight at a constant speed of 3 m/sec e.In lowering the weight at a velocity of 3 m/sec and acceleration of 1 m/sec2

Description : In which case power required would be more a.In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec b.In lowering a weight of 100 kg along an a inclined plane ... speed of 3 m/sec e.In lowering the weight at a velocity of 3 m/sec and acceleration of 1 m/sec2

Last Answer : a. In lifting up a weight of 100 kg at a velocity of 3 m/sec but accelerating upwards at 0.5 m/sec

In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Description : In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Last Answer : (A) Line of sight

When the bubble of the level tube of a level, remains central (A) Line of sight is horizontal (B) Axis of the telescope is horizontal (C) Line of collimation is horizontal (D) Geometrical axis of the telescope is horizontal

Description : When the bubble of the level tube of a level, remains central (A) Line of sight is horizontal (B) Axis of the telescope is horizontal (C) Line of collimation is horizontal (D) Geometrical axis of the telescope is horizontal

Last Answer : (A) Line of sight is horizontal

A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Description : A straight wire of length 0.20 m moves at a steady speed of 3.0 m s-1 at right angles to the magnetic field of flux density 0.10 T. The e.m.f induced across ends of wire is A. 0.5 V B. 0.06 V C. 0.05 V D. 0.04 V

Last Answer : 0.06 V

A dumpy level is set up with its eye-piece vertically over a peg . The height from the top of peg to the centre of the eye-piece is 1.540 m and the reading on peg is 0.705 m. The level is then setup over . The height of the eye-piece above peg is 1.490 m and a reading on is 2.195 m. The difference in level between and is (A) 2.900 m (B) 3.030 m (C) 0.770 m (D) 0.785 m

Description : A dumpy level is set up with its eye-piece vertically over a peg . The height from the top of peg to the centre of the eye-piece is 1.540 m and the reading on peg is 0.705 m. The level is then setup over . The height ... in level between and is (A) 2.900 m (B) 3.030 m (C) 0.770 m (D) 0.785 m

Last Answer : (C) 0.770 m

On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be (A) Downwards at its upper end (B) Upwards at its upper end (C) Perpendicular to the wall at its upper end (D) Zero at its upper end

Description : On the ladder resting on the ground and leaning against a smooth vertical wall, the force of  friction will be  (A) Downwards at its upper end  (B) Upwards at its upper end  (C) Perpendicular to the wall at its upper end  (D) Zero at its upper end 

Last Answer : (D) Zero at its upper end 

On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be (A) Towards the wall at its upper end (B) Away from the wall at its upper end (C) Upwards at its upper end (D) Downwards at its upper end

Description : On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be (A) Towards the wall at its upper end (B) Away from the wall at its upper end (C) Upwards at its upper end (D) Downwards at its upper end

Last Answer : (C) Upwards at its upper end

Dumpy level is most suitable when (a) The instrument is to be shifted frequently (b) Fly leveling is being done over long distance (c) Many readings are to be taken from a single setting of the instrument* (d) All of the above

Description : Dumpy level is most suitable when (a) The instrument is to be shifted frequently (b) Fly leveling is being done over long distance (c) Many readings are to be taken from a single setting of the instrument* (d) All of the above

Last Answer : (c) Many readings are to be taken from a single setting of the instrument*

Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m

Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the  sight on the down-slope, must be less than  (A) 30 m  (B) 25 m  (C) 20 m  (D) 15 m 

Last Answer : (B) 25 m 

While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Description : While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of ... true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Last Answer : (B) 0.15 cm

The imaginary line passing through the intersection of cross hairs and the optical centre of the objective, is known as (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Description : The imaginary line passing through the intersection of cross hairs and the optical centre of the objective, is known as (A) Line of sight (B) Line of collimation (C) Axis of the telescope (D) None of these

Last Answer : (B) Line of collimation

What is Tony Lewis Update (02/04/2020 , 22:31) ?

Description : What is Tony Lewis Update (02/04/2020 , 22:31) ?

Last Answer : Tony Lewis, one of the inventors of the Darkworth -Lewis-Stern or DLS method, has died in a weather-affected limited-overs cricket match. The England and Wales Cricket Board (ECB) made ... awarded the fifth highest honors MBE in the British Empire for their contributions to cricket and mathematics.

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

The reduced levels of the string at the consecutive sight rails A and B are 203.575 m, 203.475 m respectively. If the difference of their R.D.s is 10 m, the gradient of the sewer line is A. 1 in 100 upward B. 1 in 500 upward C. 1 in 100 downward D. 1 in 503 upward

Description : The reduced levels of the string at the consecutive sight rails A and B are 203.575 m, 203.475 m respectively. If the difference of their R.D.s is 10 m, the gradient of the sewer line is A. 1 in 100 upward B. 1 in 500 upward C. 1 in 100 downward D. 1 in 503 upward

Last Answer : ANS: C

A stone of wight 100 kg is thrown vertically upwards by a man of height y = 1.8 m with an initial velocity of 20 m/sec. The maximum height to which it will rise would be a.22.2 m b.26 m c.15.1 m d.20.2 m e.10 m

Description : A stone of wight 100 kg is thrown vertically upwards by a man of height y = 1.8 m with an initial velocity of 20 m/sec. The maximum height to which it will rise would be a.22.2 m b.26 m c.15.1 m d.20.2 m e.10 m

Last Answer : a. 22.2 m

Pick up the correct statement about silt soil from the following: (A) The silt soil has particle size from 0.02 mm to 0.06 mm (B) In organic fine grained silt soil possesses no plasticity (C) The least plastic type normally consists of more or less equidimensional grains of quartz (D) All the above

Description : Pick up the correct statement about silt soil from the following: (A) The silt soil has particle size from 0.02 mm to 0.06 mm (B) In organic fine grained silt soil possesses no ... The least plastic type normally consists of more or less equidimensional grains of quartz (D) All the above

Last Answer : Answer: Option D

A man standing on a edge of a cliff throws a stone vertically upwards with a certain speed. He then throws another stone downwards with the same speed. Find the ratio of the speeds of the two stones when they hit the ground. (1) 1 : 1 (2) 1 : 2 (3) 1 : 4 (4) Cannot be found from the given information.

Description : A man standing on a edge of a cliff throws a stone vertically upwards with a certain speed. He then throws another stone downwards with the same speed. Find the ratio of the speeds of the two stones when they hit the ground ... : 1 (2) 1 : 2 (3) 1 : 4 (4) Cannot be found from the given information.

Last Answer : (1) 1 : 1 Explanation: The stone which is throws upward will have the same velocity of u at the point of its original position when it is falling down. Another stone is thrown downwards with u. So ... will hit the ground with same velocity. So the ratio between the speeds of two stones will be 1:1

A man standing on a edge of a cliff throws a stone vertically upwards with a certain speed. He then throws another stone downwards with the same speed. Find the ratio of the speeds of the two stones when they hit the ground. (1) 1 : 1 (2) 1 : 2 (3) 1 : 4 (4) Cannot be found from the given information.

Description : A man standing on a edge of a cliff throws a stone vertically upwards with a certain speed. He then throws another stone downwards with the same speed. Find the ratio of the speeds of the two stones when they hit the ground ... : 1 (2) 1 : 2 (3) 1 : 4 (4) Cannot be found from the given information.

Last Answer :  1 : 1

The tension in the wire rope supporting a lift moving with a uniform velocity a.Is more when the lift is moving upwards b.Is more when the lift is moving downwards c.Is less when the lift is moving down-wards d.Is less when the lift is moving upwards e.Remains constant irrespective of the lift movement

Description : The tension in the wire rope supporting a lift moving with a uniform velocity a.Is more when the lift is moving upwards b.Is more when the lift is moving downwards c.Is less when the lift ... down-wards d.Is less when the lift is moving upwards e.Remains constant irrespective of the lift movement

Last Answer : e. Remains constant irrespective of the lift movement

Do stalactites grow upwards or downwards?

Description : Do stalactites grow upwards or downwards?

Last Answer : Downwards

In fireworks the momentum provided by chemicals is directed A. upwards B. left side C. right side D. downwards

Description : In fireworks the momentum provided by chemicals is directed A. upwards B. left side C. right side D. downwards

Last Answer : downwards

Charges filled inside a cylindrical will possess flux in which direction? a) Upwards b) Downwards c) Laterally outwards d) Inwards

Description : Charges filled inside a cylindrical will possess flux in which direction? a) Upwards b) Downwards c) Laterally outwards d) Inwards

Last Answer : c) Laterally outwards

An increase in marginal propensity to consume will (a) Lead to the consumption function becoming steeper. (b) Shift the consumption function upwards. © Shift the consumption function downwards. (d) Shift the savings function upwards.

Description : An increase in marginal propensity to consume will (a) Lead to the consumption function becoming steeper. (b) Shift the consumption function upwards. © Shift the consumption function downwards. (d) Shift the savings function upwards.

Last Answer : d) Lead to the consumption function becoming steeper.

Metacentre is the point of intersection of (A) Vertical upward force through e.g. of body and center line of body (B) Buoyant force and the center line of body (C) Midpoint between e.g. and center of buoyancy (D) All of the above

Description : Metacentre is the point of intersection of (A) Vertical upward force through e.g. of body and center line of body (B) Buoyant force and the center line of body (C) Midpoint between e.g. and center of buoyancy (D) All of the above

Last Answer : Answer: Option B

Calculate damping ratio if mass = 200Kg, ω = 20rad/s and damping coefficient = 800 N/m/s A. 0.03 B. 0.04 C. 0.05 D. 0.06

Description : Calculate damping ratio if mass = 200Kg, ω = 20rad/s and damping coefficient = 800 N/m/s A. 0.03 B. 0.04 C. 0.05 D. 0.06

Last Answer : A. 0.03

Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 1000 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Description : Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 1000 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Last Answer : b) 0.04

Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 800 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Description : Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 800 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Last Answer : a) 0.03

A 400kW, 3-phase, 440V, 50Hz induction motor has a speed of 950 r.p.m. on fullload. The machine has 6 poles. The slip of the machine will be _______________. (A) 0.06 (B) 0.10 (C) 0.04 (D) 0.05

Description : A 400kW, 3-phase, 440V, 50Hz induction motor has a speed of 950 r.p.m. on fullload. The machine has 6 poles. The slip of the machine will be _______________. (A) 0.06 (B) 0.10 (C) 0.04 (D) 0.05

Last Answer : Ans: D N = Ns (1-S) 950 = 120 x 50 (1-S)/6 S = 0.05

Minimum size of the particles of silt soil, is (A) 0.002 mm (B) 0.04 mm (C) 0.06 mm (D) 0.08 mm

Description : Minimum size of the particles of silt soil, is (A) 0.002 mm (B) 0.04 mm (C) 0.06 mm (D) 0.08 mm

Last Answer : (A) 0.002 mm

Maximum size of clay particles is: (A) 0.002 mm (B) 0.04 mm (C) 0.06 mm (D) 0.08 mm

Description : Maximum size of clay particles is: (A) 0.002 mm (B) 0.04 mm (C) 0.06 mm (D) 0.08 mm

Last Answer : (A) 0.002 mm

Consider a project with the following functional units : Number of user inputs = 50 Number of user outputs = 40 Number of user enquiries = 35 Number of user files = 06 Number of external interfaces = 04 Assuming all complexity adjustment factors and weighing factors as average, the function points for the project will be (A) 135 (B) 722 (C) 675 (D) 672

Description : Consider a project with the following functional units : Number of user inputs = 50 Number of user outputs = 40 Number of user enquiries = 35 Number of user files = 06 Number of external interfaces = 04 ... average, the function points for the project will be (A) 135 (B) 722 (C) 675 (D) 672

Last Answer : (D) 672

If D is the degree of a curve, the percentage reduction of gradient, is (A) 0.01 D (B) 0.02 D (C) 0.03 D (D) 0.04 D

Description : If D is the degree of a curve, the percentage reduction of gradient, is (A) 0.01 D (B) 0.02 D (C) 0.03 D (D) 0.04 D

Last Answer : Answer: Option D

The volume is measured correct to the nearest (A) 0.01 cum (B) 0.02 cum (C) 0.03 cum (D) 0.04 cum

Description : The volume is measured correct to the nearest (A) 0.01 cum (B) 0.02 cum (C) 0.03 cum (D) 0.04 cum

Last Answer : (A) 0.01 cum

The area is measured correct to the nearest (A) 0.01 sqm (B) 0.02 sqm (C) 0.03 sqm (D) 0.04 sqm

Description : The area is measured correct to the nearest (A) 0.01 sqm (B) 0.02 sqm (C) 0.03 sqm (D) 0.04 sqm

Last Answer : (A) 0.01 sqm

Maximum area of compression reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Description : Maximum area of compression reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Last Answer : [ C ] 0.04 bd

Maximum area of tension reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Description : Maximum area of tension reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Last Answer : [ D ] 0.04 bD