If d is the diameter of the pipe, p is the total internal pressure, f is the permissible tensile stress
and n is the effective of the joint, the thickness t of metal pipe, is
(A) n (pd/2f)
(B) (1/n) (pd/2f)
(C) (1/n) (pd/3f)
(D) (1/n) (pf/d
Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t
Last Answer : (A) pd/2t
Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm
Last Answer : b) 2.5cm
Description : The maximum magnitude of shear stress due to shear force F on a rectangular section of area A at the neutral axis, is (A) F/A (B) F/2A (C) 3F/2A (D) 2F/3A
Last Answer : (C) 3F/2A
Description : Reduction in vibration amplitude after one complete cycle of single degree free vibration with dry friction damping is_____, if where F"= frictional force between mass and surface and k =stiffness of the system. a)4F/k a b) 2f/K C) 3F/k D)8F/k
Last Answer : a)4F/k
Description : Two condensers of capacity 2F and 3F are connected in Series and a third condenser of 1F is connected in parallel to them. The resultant capacity will
Last Answer : Two condensers of capacity 2F and 3F are connected in Series and a third condenser of 1F is connected in parallel to them. The resultant capacity will 11/5 F
Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm
Last Answer : Answer: Option C
Description : The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2
Last Answer : Answer: Option A
Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2
Last Answer : [ D ] 2.8 N/mm2
Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t
Last Answer : (d) 16 t
Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above
Last Answer : Answer: Option D
Description : The pressure exerted by A. The sewage when running full from inside, is called internal pressure B. The internal pressure if any, causes tensile stress in the pipe material C. Pressure sewers are designed to be safe in tension D. All the above
Last Answer : ANS: D
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2
Last Answer : b) 450 N/mm2
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : A sliding contact bearing is operating under stable condition. The pressure developed in oil film is p when the journal rotates at N rpm. The dynamic viscosity of lubricant is μ and effective coefficient of ... to p and f) (d) f is directly proportional to μ and inversely proportional to N
Last Answer : (b) f is directly proportional to μ and N
Description : A reinforced concrete beam will crack if tensile stress set up in the concrete below the neutral axis is (a) More than the permissible stress (b) Less than the permissible stress (c) Equal to the permissible stress (d) All the above.
Last Answer : (a) More than the permissible stress
Description : Under normal loading conditions, the tensile stressed setup in the concrete will be _________the permissible stress. (a) More than (b) Less than (c) Equal to (d) All the above
Last Answer : (a) More than
Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm
Last Answer : Answer: Option B
Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface
Last Answer : c) maximum at the inner surface and zero at the outer surface
Description : Steel pipe are (A) Suitable for withstanding high internal pressure (B) Connected by riveted or welded joints (C) Generally laid underground and no expansion joint is required (D) Likely to last 100 years under ordinary conditions
Last Answer : (D) Likely to last 100 years under ordinary conditions
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : The maximum load to which a fillet joint of length can be subjected to, is (A) 0.7 × S × fillet size × L (B) 2 × S × fillet size × L (C) Permissible shear stress × fillet size × L (D) (S × fillet size × L)/3
Last Answer : (A) 0.7 × S × fillet size × L
Description : Draw the ray diagram in each case to show the position and nature of the image formed when the object is placed: (i) at the centre of curvature of a concave mirror (ii) between the pole P and focus F of ... front of a convex mirror (iv) at 2F of a convex lens (v) in front of a concave lens -Physics
Last Answer : Answer. Nature of image: Real, inverted and same size image is formed at the centre of curvature. Nature of image: Virtual, enlarged and erect image is formed behind the mirror. Nature of image: Virtual ... : Virtual, erect and diminished image is formed between O and F on the same side of object.
Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib
Last Answer : (d) Depth of rib
Description : The pressure drop in a 30 cm diameter horizontal pipe is 60 kPa in distance of 15m. The wall shear stress in kPa is (a) 0.1 (b) 0.2 (c) 0.3 (d) 0.4
Last Answer : (c) 0.3
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : Pick out the wrong statement. (A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1 (B) For calculating forces and ... Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
Last Answer : Option B
Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters
Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters
Description : If the bond stress developed in a reinforced concrete beam is more than permissible value, it can be brought down by. (a) Increasing the depth of beam (b) Increasing the number of bars. (c) Decreasing the diameter of the bars (d) All of these
Last Answer : (d) All of these
Description : Longitudinal stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t
Last Answer : c) PD/4t
Description : Tangential stress in a cylinder is given by [symbols have their usual meanings]. a) PD/2t b) 2PD/t c) PD/4t d) 4PD/t
Last Answer : a) PD/2t
Description : Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress
Last Answer : c. Ultimate stress / Permissible stress
Description : If two tensile forces mutually perpendicular act on a rectangular parallelepiped bar are equal, the resulting elongation of the pipe, is (A) (P/E) (1 - m) (B) (E/P) (m -1) (C) (E/P) (1 - m) (D) (P/E) (1 + m)
Last Answer : (A) (P/E) (1 - m)
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3
Last Answer : (C) 1/2
Description : If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)
Description : If tensile stress of a steel rod of diameter is 1400 kg/cm2 and bond stress is 6 kg/cm2 , the required bond length of the rod is (A) 30 D (B) 39 D (C) 50 D (D) 59 D
Last Answer : (D) 59 D
Description : A joint of a frame is subjected to three tensile forces P, Q and R equally inclined to each other. If P is 10 tonnes, the other forces will be (A) Q = 10 tonnes and R = zero (B) R + 10 tonnes and Q = zero (C) Q + R = 10 tonnes (D) Q and R each is equal to 10 tonnes
Last Answer : (D) Q and R each is equal to 10 tonnes
Description : Disc compensators are provided in large diameter fuel gas carrying pipelines to (A) Keep the pipe in proper orientation (B) Make the pipe joint leak-proof (C) Account for contraction/expansion ... due to temperature changes of the surroundings (D) Account for the pressure variation side the pipeline
Last Answer : (C) Account for contraction/expansion of pipe due to temperature changes of the surroundings
Description : What is 3f plus f plus 4f equal?
Last Answer : 7f
Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed
Last Answer : b) 360/t
Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed
Last Answer : c) 5.07mm
Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm
Last Answer : c) 8mm
Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness
Last Answer : c. Length
Description : A 3.2 m diameter balloon is filled with Helium. The total weight of balloon, gas and pay load is 10 kg kg. In an isothermal atmosphere having conditions identical to N.T.P. the balloon will rise to a height of about a.6000 m b.1500 m c.3000 m d.2000 m e.1000 m
Last Answer : a. 6000 m
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Description : As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2
Last Answer : (b) 1 N/mm2
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2