Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed
Last Answer : b) 1.21P/hl
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed
Last Answer : b) 1102.8N
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : b) 32M/πdɜ
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4
Last Answer : b) None of the listed
Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed
Last Answer : a) 0.707 hl
Description : Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t
Last Answer : c) 250000 t
Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed
Last Answer : a) Leg
Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T
Last Answer : (A) T/2
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Last Answer : b) False
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : c) 16M/πdɜ
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types
Last Answer : E. All types
Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160
Last Answer : 2. 790
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress
Last Answer : (A) Direct tensile stress and bending stress
Description : The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these
Last Answer : B. Zero at the point other than centroidal axis
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated
Last Answer : b) No
Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams
Last Answer : (A) Maximum principal stress theory
Description : Is principal a? a. Simple stress b. Complex stress c. Bending stress d. None
Last Answer : a. Simple stress
Description : Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None
Last Answer : (a) Normal stress
Description : Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None
Last Answer : (c) Compressive stress
Description : A principal plane is a plane of (a) Only normal stress (b) Only shear stress (c) Only bending stress (d) None
Last Answer : (a) Only normal stress
Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above
Last Answer : c. Principal stress
Description : The bending stress in a curved beam is (A) Zero at the centroidal axis (B) Zero at the point other than centroidal axis (C) Maximum at the neutral axis (D) None of these
Last Answer : (B) Zero at the point other than centroidal axis
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed
Last Answer : a) Race rotation factor
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : b) 32M/πdᵌ
Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )
Last Answer : b. ( K f – 1 ) / ( K t – 1 )
Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.
Last Answer : (a) butt weld
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False