List any four types of electrical faults that may occur on electric locomotive with their causes.

List any four types of electrical faults that may occur on electric locomotive with their causes.
by

1 Answer

Answer :

Electric faults and causes in electric locomotive: Changes in the conditions of overloading leading to heating of winding , failure of insulation. Changes in the operating environments such as temperature, moisture, dust etc. leading to failure of insulation, over- heating and chances of short circuit. Changes in the condition of equipment itself such as aging leads to open circuit, deterioration of insulation, wear leads to chances of short circuit. External influences of abnormal nature like voltage surges, lightning, short circuits elsewhere leading to chances of short circuit, overheating, burning of equipment etc. Improper operation due to bad maintenance either due to lack of attention which should have been given .

by

Related questions

List any four mechanical and electrical faults in SWT.

Description : List any four mechanical and electrical faults in SWT.

Last Answer : Mechanical Faults in SWT: 1. Bearing and gearbox issue 2. Blade design , manufacturing, installation issue 3. Mechanical break down 4. Hydraulic failure 5. Nacelle ... failure, power regulator failure 12. Torque reversal due occasional connecting and disconnecting generator to grid

List any eight equipment used in auxiliary circuit of electric locomotive.

Description : List any eight equipment used in auxiliary circuit of electric locomotive.

Last Answer : Ans: 1) Batteries , 2) Compressor , 3) Blowers , 4) Exhausters , 5) Pumps , 6) Cab ventilating fans.7) Locomotive heating (if any) , 8) Transformer oil cooling radiator. 9) head light , 10) Flasher light , 11) Marker light , 12) Engine Horn

List any two types of relays and contactors with their function used in AC locomotive.

Description : List any two types of relays and contactors with their function used in AC locomotive.

Last Answer : Types of relays and their function in AC locomotive: 1) Buchholz Relay: To protect traction transformer from incipient faults. 2) Earth fault or Ground fault Relay: To protect the system against all kinds of ... is engaged with cam on shaft. Cam shaft can be moved by air engine or vane motor. 

State the function of a contactor in a power circuit of locomotive. List different types of it and state one application of each.

Description : State the function of a contactor in a power circuit of locomotive. List different types of it and state one application of each.

Last Answer : Ans: Contactor in power circuit of locomotive is used to connect relevant sections for operation. Connecting or disconnecting the power circuit at different conditions of operation and at different locations. ... heavy power currents. 3) Cam & roller operated - used for group switching.

A LRU page replacement is used with four page frames and eight pages. How many page faults will occur with the reference string 0172327103 if the four frames are initially empty? (A) 6 (B) 7 (C) 5 (D) 8

Description : A LRU page replacement is used with four page frames and eight pages. How many page faults will occur with the reference string 0172327103 if the four frames are initially empty? (A) 6 (B) 7 (C) 5 (D) 8

Last Answer : (B) 7

Suppose that the virtual Address space has eight pages and physical memory with four page frames. If LRU page replacement algorithm is used, .............. number of page faults occur with the reference string. 0 2 1 3 5 4 6 3 7 4 7 3 3 5 5 3 1 1 1 7 2 3 4 1 (A) 11 (B) 12 (C) 10 (D) 9

Description : Suppose that the virtual Address space has eight pages and physical memory with four page frames. If LRU page replacement algorithm is used, .............. number of page faults occur with the reference string. 0 2 1 3 5 4 6 3 7 4 7 3 3 5 5 3 1 1 1 7 2 3 4 1 (A) 11 (B) 12 (C) 10 (D) 9

Last Answer : (A) 11

Explain the need of maintenance of electric locomotive.

Description : Explain the need of maintenance of electric locomotive. 

Last Answer : Need for maintenance : To correct the effects of Wearing out. To correct the effects of deterioration of locomotive component during normal use. In the long run (aging) performance ... availability of locomotive.  Ensures reliability and operational readiness. Ensures safety by all means.

State the function of following auxiliaries used in electric locomotive, i) Batteries ii ) Compressor iii ) Blower iv ) Exhauster

Description : State the function of following auxiliaries used in electric locomotive, i) Batteries ii ) Compressor iii ) Blower iv ) Exhauster 

Last Answer : Ans: 1) Batteries - supply to run baby compressor which supplies air for initial raising of pantograph and closing of air blast circuit breaker. 2) Compressor - supply air for operation, control and ... blower, reactor blower, SCR blower, traction motor blower etc. 4) Exhausters - for vacuum brakes.

What are causes of faults in power system? State any four harmful effects of faults.

Description : What are causes of faults in power system? State any four harmful effects of faults.

Last Answer : Causes of Faults in the Power System:  1) Breaking of Conductors: It is one of major causes of faults. Breaking of conductors is due to excessive heat or because of mechanical stresses ... maintenance of machines / equipment / lines / protective system leads to faults in the power system.

Sparking of D.C. motor brushes can be caused by __________. A. an open commutating winding B. many mechanical, electrical or operating faults C. an open interpole D. all of the above

Description : Sparking of D.C. motor brushes can be caused by __________. A. an open commutating winding B. many mechanical, electrical or operating faults C. an open interpole D. all of the above

Last Answer : Answer: B

Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on different phases will not cause an outage. C. Ground detection systems are unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Description : Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on ... unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Last Answer : Answer: A

Earthquakes that occur along faults are created when ___________ a) Melted rock is erupted along the fault zone b) Stress builds up until rocks break c) The earth shifts and moves along fracture d) Answers b and c

Description : Earthquakes that occur along faults are created when ___________ a) Melted rock is erupted along the fault zone b) Stress builds up until rocks break c) The earth shifts and moves along fracture d) Answers b and c

Last Answer : d) Answers b and c

State and explain the faults occur in the transformers.

Description : State and explain the faults occur in the transformers.

Last Answer : Sr. No. Type of fault Explanation 1 Earth fault Due to breakdown of insulation between live conducting parts such as winding, terminals etc. and earthed metallic parts such as ... place and few turns of the same winding are shortcircuited, the inter-turn fault takes place.

Explain the surge protection of electric locomotive from i) Direct lightening stroke ii) Switching surges

Description : Explain the surge protection of electric locomotive from i) Direct lightening stroke ii) Switching surges

Last Answer : i)Protection of Electric Locomotive From Direct Lightening Stroke:  1. The direct lightning strokes may strike on the overhead conductor on the roof of the locomotive. 2. To protect the ... reduce the steepness of the wave front and also help to absorb the energy in the resistance.

Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Description : Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Last Answer : labelled diagram ofAC electric locomotive:  Function of AC electric locomotive Parts: 1) Overhead contact wire: Supply of 1-ph, 25KV, 50Hz, AC is given to overhead conductor. 2) Current collecting ... mechanical power to run the train i.e. DC series motor which is used as traction motor.

In a steam locomotive electric power is provided through?

Last Answer : In a steam locomotive electric power is provided through small turbo-generator.

How does electric locomotive work?

Description : How does electric locomotive work?

Last Answer : Electric  locomotives  are  powered   by  motors  connected  to  battery  or  any  supply . The  electric  supply  is  connected  to  a  motor  which  drives  set  of  gears  connected  to  wheels.

State the nature of protection provided for following types of faults; 1) Over voltage 2) Under voltage 3) High air pressure in air circuit 4) Low air pressure in air circuit

Description : State the nature of protection provided for following types of faults; 1) Over voltage 2) Under voltage 3) High air pressure in air circuit 4) Low air pressure in air circuit

Last Answer : Ans:  1) Over voltage: Controlled through tap changing, only an alarm needs to be provided for attention of crew.  2) Under voltage: voltage below 17.5 kV is not desirable. A no volt ... 4) Low air pressure in air crcuit: Relay senses low pressure in air circuit and trips the relevant CB.

What do you call the programs that are used to find out possible faults and their causes? A) Operating system extensions B) Cookies C) Diagnostic software D) Boot diskettes

Description : What do you call the programs that are used to find out possible faults and their causes? A) Operating system extensions B) Cookies C) Diagnostic software D) Boot diskettes

Last Answer : Answer : C

Match the following: List-I List-II A. Varanasi I. Indian Rare Earths Ltd B. Koyali II. Hindustan Machine Tools Ltd C. Pinjore III. Diesel Locomotive Works D. Alwaye IV. Petro-Chemical Complex Codes: A B C D (a) I II III IV (b) IV III II I (c) III IV II I (d) III IV I II

Description : Match the following: List-I List-II A. Varanasi I. Indian Rare Earths Ltd B. Koyali II. Hindustan Machine Tools Ltd C. Pinjore III. Diesel Locomotive Works D. Alwaye IV. Petro-Chemical Complex Codes: A B C D (a) I II III IV (b) IV III II I (c) III IV II I (d) III IV I II

Last Answer : Ans: (c)

State any four faults in centrifugal pump and their remedies

Description : State any four faults in centrifugal pump and their remedies

Last Answer : Sr.No Fault remedies 1 Pump fails to start pumping Reprime the pump , Clean the impeller Reduce suction lift , Increase the speed 2 Pump stops working ... Reduce the speed Correct the direction of rotation of impeller Reduce the discharge , Repair affected parts

List any four internal causes for abnormal operation of electrical equipment’s.

Description : List any four internal causes for abnormal operation of electrical equipment’s. 

Last Answer : Internal causes:- 1. Open circuit 2. Short circuit 3. Earth fault 4. Loose connection 5. Deposit of dirt and dust near ventilation passage 6. Low insulation resistance 7. Improper maintenance 8. Poor ... problems 13. Failure of cooling system 14. Excess wear and tear of internal parts 15. Ageing.

What are the causes of bus zone faults?

Description : What are the causes of bus zone faults?

Last Answer : Failure of support insulator resulting in earth fault Flashover across support insulator during over voltage Heavily polluted insulator causing flashover Earthquake, mechanical damage etc.

Discuss causes and remedies for following faults in CI engine: (i) Engine does not start or stalls just after starting (ii) Excessive fuel consumption.

Description : Discuss causes and remedies for following faults in CI engine: (i) Engine does not start or stalls just after starting (ii) Excessive fuel consumption.

Last Answer : I) Engine does not start or stalls just after starting

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

Consider the reference string 0 1 2 3 0 1 4 0 1 2 3 4 If FIFO page replacement algorithm is used, then the number of page faults with three page frames and four page frames are .......... and ........... respectively. (A) 10, 9 (B) 9, 9 (C) 10, 10 (D) 9, 10

Description : Consider the reference string 0 1 2 3 0 1 4 0 1 2 3 4 If FIFO page replacement algorithm is used, then the number of page faults with three page frames and four page frames are .......... and ........... respectively. (A) 10, 9 (B) 9, 9 (C) 10, 10 (D) 9, 10

Last Answer : (D) 9, 10

The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults could be the cause? EL-0102 A. Master switch contact 'MS3' may have defective springs. B. Contactor '3M' coil could have an open winding. C. Contact '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Description : The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults ... '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Last Answer : Answer: A

Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Description : Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Last Answer : (d) all of the above

What are the different types of faults in a transformer?

Description : What are the different types of faults in a transformer?

Last Answer : The internal faults include phase faults, ground faults, inter-turn faults, tap-changer failure, and leakage oil from tank. The external faults include system phase faults, system ground faults, over loads and over fluxing.

State the various types of unsymmetrical faults.

Description : State the various types of unsymmetrical faults.

Last Answer : Line to ground ,line to line and double line to ground faults

State the different types of faults.

Description : State the different types of faults.

Last Answer : Symmetrical faults and unsymmetrical faults and open conductor faults.

What are the main types of stator winding faults?

Description : What are the main types of stator winding faults?

Last Answer : Fault between phase and ground; fault between phases and inter-turn fault involving turns of the same phase winding.

Explain different types of faults occurs in rocks.

Description : Explain different types of faults occurs in rocks. 

Last Answer : Types of Faults: 1. Normal Faults a. Horst & Graben b. Half- Grabens 2. Reverse Faults a. Thrust Faults b. Overthrust Faults c. Underthrust Faults 3. Strike Fault 4. Dip Fault 5 ... Faults 13. Enechelon Faults 14. Transform Faults 15. Ring Faults 16. Listric Faults 17. Oblique Faults

Define faults and state any two types of fault.

Description : Define faults and state any two types of fault.

Last Answer : Fault: It is defined as the rupture / fracture along which there is a relative movement of beds. Types of fault : 1. Based on position of fault plane. i. Normal Fault ii. Reverse Fault 2. Based on ... fault 3. Horst and Graben 4. Step fault 5. Bedding fault 6. Dip fault 7. Strike fault  

The San Andreas fault in California is a classic example of which of the following types of faults? w) tear fault x) upthrust fault y) dip-slip fault z) strike-slip fault

Description : The San Andreas fault in California is a classic example of which of the following types of faults? w) tear fault x) upthrust fault y) dip-slip fault z) strike-slip fault

Last Answer : ANSWER: Z -- STRIKE-SLIP FAULT

In geological studies, a reverse fault having a di less than 10 degrees is known as which of the following types of faults. w) normal x) overthrust y) strike-slip z) none of the above.

Description : In geological studies, a reverse fault having a di less than 10 degrees is known as which of the following types of faults. w) normal x) overthrust y) strike-slip z) none of the above.

Last Answer : ANSWER: X -- OVERTHRUST

The severity of line to ground and three phase faults at the terminals of an unloaded

Description : The severity of line to ground and three phase faults at the terminals of an unloaded synchronous generator is to be same. If the terminal voltage is 1.0 pu, Z1=Z2=j0.1 p.u. and Z0= j0.05 p.u. for the alternator, then the required inductive ... a) 0.05 p.u. (b) 0.0166 p.u. (c) 0.1 p.u. (d) 0.15 p.u.

Last Answer : The severity of line to ground and three phase faults at the terminals of an unloaded synchronous generator is to be same. If the terminal voltage is 1.0 pu, Z1=Z2=j0.1 p.u. and Z0= j0.05 p.u. for the alternator, then the required inductive reactance for neutral grounding is 0.0166 p.u.

Which portion of the transmission system is more prone to faults ?

Description : Which portion of the transmission system is more prone to faults ?   (a) Alternator (b) Transformer (c) Overhead lines (d) Underground cables

Last Answer : C

In which type of the faults given below, all of the three components Ia0, Ia1 and Ia2 are equal?

Description :  In which type of the faults given below, all of the three components Ia0, Ia1 and Ia2 are equal?  (A) Single line to ground fault (B) Double line to ground fault (C) Line to line fault (D) 3 phase faults

Last Answer : (A) Single line to ground fault

Define the term electrical noise. List types of noises.

Description : Define the term electrical noise. List types of noises.

Last Answer : Electrical Noise:- It can be defined as undesirable electrical signals, which distort or interfere with an original (or desired) signal.  Types of noises:- 

List any two types of fuels used in electrical power generation plants.

Description : List any two types of fuels used in electrical power generation plants.

Last Answer : Types of fuels used in electrical power generation plants:  1) Solid fuels: Coal, Biomass: Wood, Nuclear fuel: Uranium, Plutonium  2) Liquid fuels: Diesel, Petrol  3) Gaseous Fuels: Natural gas, Producer ... 2) Wood 3) Uranium 4) Plutonium 5) Diesel 6) Petrol 7) Natural gas 8) Producer gas

List four electric pressure transducer.

Description : List four electric pressure transducer.

Last Answer : List of electric pressure measuring devices: 1. Diaphragm with strain gauge 2. Bourdon Tube with LVDT 3. Differential Pressure cell 4. Piezoelectric type pressure transducer 5. Capacitance pressure transducer 6. Optical Pressure transducer 7. Resistive pressure transducer 

List out the four applications of diesel electric power plant.

Description : List out the four applications of diesel electric power plant.

Last Answer : Applications of Diesel Power Plant: 1. It can be used as a standby (emergency) power plant to maintain continuity of supply. (Incase failure of main supply like hospital, Telephone exchange Radio stations, ... 10. Diesel plants are widely used for generating power ranging from 100 to 5,000 H.P.

List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Description : List out any four effects of electric current used in measuring instruments & write name of meter working on it.

Last Answer : Effects of Electric Current used in measuring instruments:  1. Magnetic Effect: PMMC and Moving Iron type Ammeters, voltmeter and Dynamometer type wattmeters etc.  2. Electromagnetic induction ... . Electrostatic effect: Voltmeters.  5. Hall Effect: Flux meter, Poynting vector wattmeter.

The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is 15 N per kN, the maximum speed that the locomotive can attain on level track will be a.43 kmph b.83 kmph c.103 kmph d.107 dynes e.38 kmph

Description : The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is 15 N per kN, the maximum speed that the locomotive can attain on level track will be a.43 kmph b.83 kmph c.103 kmph d.107 dynes e.38 kmph

Last Answer : e. 38 kmph

The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is qN per kN, the maximum speed that the locomotive can attain on level track will be a.103 kmph b.83 kmph c.107 dynes d.43 kmph e.63 kmph

Description : The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is qN per kN, the maximum speed that the locomotive can attain on level track will be a.103 kmph b.83 kmph c.107 dynes d.43 kmph e.63 kmph

Last Answer : e. 63 kmph

A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in 10 sec. The distance between the locomotive and the wagons at this instant assuming that the forces acting on the train are unaltered would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Description : A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in ... would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Last Answer : d. 0.5 m

What was the the name of the first steam powered locomotive by George Stephenson?

Description : What was the the name of the first steam powered locomotive by George Stephenson?

Last Answer : Rocket*Skinny mini*

Who was the first African American locomotive engineer for Houston Beltway Terminal?

Description : Who was the first African American locomotive engineer for Houston Beltway Terminal?

Last Answer : Feel Free to Answer

How much is a 2 cents Locomotive 1870 stamp worth?

Description : How much is a 2 cents Locomotive 1870 stamp worth?

Last Answer : Feel Free to Answer