In which type of the faults given below, all of the three components Ia0, Ia1 and Ia2 are equal?

 In which type of the faults given below, all of the three components Ia0, Ia1 and Ia2 are equal? 

(A) Single line to ground fault (B) Double line to ground fault (C) Line to line fault (D) 3 phase faults
by

1 Answer

Answer :


(A) Single line to ground fault

by

Related questions

The severity of line to ground and three phase faults at the terminals of an unloaded

Description : The severity of line to ground and three phase faults at the terminals of an unloaded synchronous generator is to be same. If the terminal voltage is 1.0 pu, Z1=Z2=j0.1 p.u. and Z0= j0.05 p.u. for the alternator, then the required inductive ... a) 0.05 p.u. (b) 0.0166 p.u. (c) 0.1 p.u. (d) 0.15 p.u.

Last Answer : The severity of line to ground and three phase faults at the terminals of an unloaded synchronous generator is to be same. If the terminal voltage is 1.0 pu, Z1=Z2=j0.1 p.u. and Z0= j0.05 p.u. for the alternator, then the required inductive reactance for neutral grounding is 0.0166 p.u.

List any four types of electrical faults that may occur on electric locomotive with their causes.

Description : List any four types of electrical faults that may occur on electric locomotive with their causes.

Last Answer : Electric faults and causes in electric locomotive: Changes in the conditions of overloading leading to heating of winding , failure of insulation. Changes in the operating environments such as temperature, ... due to bad maintenance either due to lack of attention which should have been given .

State the nature of protection provided for following types of faults; 1) Over voltage 2) Under voltage 3) High air pressure in air circuit 4) Low air pressure in air circuit

Description : State the nature of protection provided for following types of faults; 1) Over voltage 2) Under voltage 3) High air pressure in air circuit 4) Low air pressure in air circuit

Last Answer : Ans:  1) Over voltage: Controlled through tap changing, only an alarm needs to be provided for attention of crew.  2) Under voltage: voltage below 17.5 kV is not desirable. A no volt ... 4) Low air pressure in air crcuit: Relay senses low pressure in air circuit and trips the relevant CB.

Which portion of the transmission system is more prone to faults ?

Description : Which portion of the transmission system is more prone to faults ?   (a) Alternator (b) Transformer (c) Overhead lines (d) Underground cables

Last Answer : C

Short-circuit currents are due to (a) single phase to ground faults (b) phase to phase faults (c) two phase to ground faults (d) three phase faults (e) any of these

Description : Short-circuit currents are due to (a) single phase to ground faults (b) phase to phase faults (c) two phase to ground faults (d) three phase faults (e) any of these

Last Answer : (e) any of these

Consider the reference string 0 1 2 3 0 1 4 0 1 2 3 4 If FIFO page replacement algorithm is used, then the number of page faults with three page frames and four page frames are .......... and ........... respectively. (A) 10, 9 (B) 9, 9 (C) 10, 10 (D) 9, 10

Description : Consider the reference string 0 1 2 3 0 1 4 0 1 2 3 4 If FIFO page replacement algorithm is used, then the number of page faults with three page frames and four page frames are .......... and ........... respectively. (A) 10, 9 (B) 9, 9 (C) 10, 10 (D) 9, 10

Last Answer : (D) 9, 10

Identify the components labelled A, B, C and D in the diagram below from the list (i) to (vii) given along with Components : (i) Cristae of mitochondr

Description : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (vii) given along with Components : (i) Cristae of mitochondr

Last Answer : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (vii) given along with ... v)","(iv)","(viii)","(iii)"):}`

Find the central angles of the components of a data given below, when represented in a pie chart ? `{:(bar("Component Food Education Rent Clothing Sav

Description : Find the central angles of the components of a data given below, when represented in a pie chart ? `{:(bar("Component Food Education Rent Clothing Sav

Last Answer : Find the central angles of the components of a data given below, when represented in a pie chart ? `{:( ... Rs.) 3600 2400 2100 1200 1500 10800")):}`

Given below is the ECG of a normal human. Which one of its components is correctly interpreted below? (a) Complex QRS - one complete pulse (b) Peak T - initiation of total cardiac contraction (c) Peak P and peak R together - systolic and diastolic blood pressures (d) Peak P- initiation of left atrial contraction only

Description : Given below is the ECG of a normal human. Which one of its components is correctly interpreted below? (a) Complex QRS - one complete pulse (b) Peak T - initiation of total cardiac ... R together - systolic and diastolic blood pressures (d) Peak P- initiation of left atrial contraction only

Last Answer : (a) Complex QRS - one complete pulse

Identify the components labelled A, B, C and D in the diagram below from the list (i) to (viii) given along withComponents : (i) Cristae of mitochondria (ii) Inner membrane of mitochondria (iii) Cytoplasm (iv) Smooth endoplasmic reticulum (v) Rough endoplasmic reticulum (vi) Mitochondrial matrix (vii) Cell vacuole (viii) Nucleus The correct components are: A B C D (a) (v) (iv) (viii) (iii) (b) (i) (iv) (viii) (vi) (c) (vi) (v) (iv) (vii) (d) (v) (i) (iii) (ii)

Description : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (viii) given along with Components : (i) Cristae of mitochondria (ii) Inner membrane of mitochondria (iii) Cytoplasm (iv) Smooth endoplasmic ... viii) (vi) (c) (vi) (v) (iv) (vii) (d) (v) (i) (iii) (ii)

Last Answer : (a) (v) (iv) (viii) (iii)

Read the different components from (i) to (iv) in the list given below and tell the correct order of the components with reference to their arrangement from outer side to inner side in a woody dicot stem. (i) Secondary cortex (ii) Wood (iii)Secondary phloem (iv) Phellem The correct order is (a) (iv), (i), (iii), (ii) (b) (iv), (iii), (i), (ii) (c) (iii), (iv), (ii), (i) (d) (i), (ii), (iv), (iii).

Description : Read the different components from (i) to (iv) in the list given below and tell the correct order of the components with reference to their arrangement from outer side to inner side in a woody dicot stem. (i) Secondary cortex (ii) Wood ... ) (c) (iii), (iv), (ii), (i) (d) (i), (ii), (iv), (iii).

Last Answer : (a) (iv), (i), (iii), (ii)

What type of mountains form at large-scale normal faults where the footwall and hanging wall spread apart from each other?

Description : What type of mountains form at large-scale normal faults where the footwall and hanging wall spread apart from each other?

Last Answer : What is the answer ?

Is it true that it's hard for people to realize their own faults?

Description : Is it true that it's hard for people to realize their own faults?

Last Answer : I still think you should have just taken it back to the school that you took it from. I wouldn't have taken someone else's bag home to begin with. Maybe she isn't the only one not seeing ... or face them. Sometimes they realize their faults some time after the event. Hindsight is 20/20, you know.

Are you willing to admit your driving faults?

Description : Are you willing to admit your driving faults?

Last Answer : answer:I have poor peripheral vision, as well as dyscalculia - which affects my ability to distinguish left from right, as well as accurately judge distance. As a result, I am an exceptionally cautious ... a garage spot and walk an extra block than park on the street in front of my destination.

How much does it bother you when other people project their faults onto you?

Description : How much does it bother you when other people project their faults onto you?

Last Answer : I usually pick it up for what it is early, and don’t let them get to me. Always remember you control your emotions and feelings. Don’t let others make you feel their problems.

What are your qualities...what are your faults?

Description : What are your qualities...what are your faults?

Last Answer : I am an excellent leader. I am great at big ideas. I am loyal and passionate. I do not have patience, I can be unforgiving, I have a love/hate relationship with humanity.

Why is it so easy to dog humanity, and condemn the species for all of its faults, including it's technology, and ignore the spectacular, technical phenomenon of the rescue of the Chilean miners?

Description : Why is it so easy to dog humanity, and condemn the species for all of its faults, including it's technology, and ignore the spectacular, technical phenomenon of the rescue of the Chilean miners?

Last Answer : I am sure there are some that will say this is the exception that proves the rule.

27" i7 iMac's, do they have noisy harddrives? do they have any other recent faults?

Description : 27" i7 iMac's, do they have noisy harddrives? do they have any other recent faults?

Last Answer : No, they do not. they run pretty much silent. i’ve never heard this claim regarding the HDD on the iMac.

Python Scipy : Segmentation Faults when slicing (splitting into train and test sets) large csr_matrix -Web-Development

Description : Python Scipy : Segmentation Faults when slicing (splitting into train and test sets) large csr_matrix -Web-Development

Last Answer : answer:

What are symmetrical and asymmetrical faults ?

Description : What are symmetrical and asymmetrical faults ?

Last Answer : Symmetrical Fault: The same amount in each phase due to the float in the electrical system. The fault that causes hot current to flow is called semantic fault. Circuit breaker ratings are determined by ... through each fan is called an asymmetrical fault. The relay is set via asymmetrical font.

What is one of the faults of imperialism that becomes clear in Heart of Darkness?

Description : What is one of the faults of imperialism that becomes clear in Heart of Darkness?

Last Answer : the colonists activities are largely ineffective -apex

In a particular volcanic region many small faults fracture the rocks of the crust. What features are likely to form beneath?

Description : In a particular volcanic region many small faults fracture the rocks of the crust. What features are likely to form beneath?

Last Answer : What is the answer ?

Where are most faults found?

Description : Where are most faults found?

Last Answer : joining two segments of a mid-ocean ridge

What do you call the programs that are used to find out possible faults and their causes? A) Operating system extensions B) Cookies C) Diagnostic software D) Boot diskettes

Description : What do you call the programs that are used to find out possible faults and their causes? A) Operating system extensions B) Cookies C) Diagnostic software D) Boot diskettes

Last Answer : Answer : C

Rift Valley is formed – (1) between two anticlines (2) between two faults (3) erosion of synclinal basin (4) due to volcanic eruption

Description : Rift Valley is formed – (1) between two anticlines (2) between two faults (3) erosion of synclinal basin (4) due to volcanic eruption

Last Answer : (2) between two faults Explanation: A rift valley is a linear-shaped lowland between several highlands or mountain ranges created by the action of a geologic rift or fault. It is formed by the subsidence of a segment of the Earth's crust between dip-slip, or normal, faults.

Earthquakes are generally associated with : (1) Joints (2) Faults (3) Folds (4) Schistosity

Description : Earthquakes are generally associated with : (1) Joints (2) Faults (3) Folds (4) Schistosity

Last Answer : (2) Faults Explanation: Earthquake is a sudden and violent movement, or fracture, within the earth followed by the series of shocks resulting from this fracture. Earthquake is more likely to be of Tectonic origin and probably because of existence of a Fault.

The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults could be the cause? EL-0102 A. Master switch contact 'MS3' may have defective springs. B. Contactor '3M' coil could have an open winding. C. Contact '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Description : The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults ... '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.

Last Answer : Answer: A

Which of the listed faults cannot be eliminated, EXCEPT by turning or grinding a commutator with a rigidly supported tool? A. Sparking brushes B. Eccentricity C. High mica D. Blackened commutator

Description : Which of the listed faults cannot be eliminated, EXCEPT by turning or grinding a commutator with a rigidly supported tool? A. Sparking brushes B. Eccentricity C. High mica D. Blackened commutator

Last Answer : Answer: B

Sparking of D.C. motor brushes can be caused by __________. A. an open commutating winding B. many mechanical, electrical or operating faults C. an open interpole D. all of the above

Description : Sparking of D.C. motor brushes can be caused by __________. A. an open commutating winding B. many mechanical, electrical or operating faults C. an open interpole D. all of the above

Last Answer : Answer: B

Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on different phases will not cause an outage. C. Ground detection systems are unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Description : Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on ... unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Last Answer : Answer: A

How Transformer Protection provided for internal faults?

Description : How Transformer Protection provided for internal faults?

Last Answer : 1.Bucholz Relay (1st Stage Alarm and 2nd Stage Trip) 2.Sudden Pressure Relay (1st Stage Alarm and 2nd Stage Trip) 3.Pressure Relief Valve (1st Stage Alarm and 2nd Stage Trip) 4.Pressure Switch ... 8.Gas Temperature Indicator (Alarm) 9.Silicon Breather (Passive - no alarm) 10.Smoke Detector (Alarm)

What are the tests done to minimize internal faults?

Description : What are the tests done to minimize internal faults?

Last Answer : 1.Dissolved Gas Analysis (DGA): Faults due to arcing, high current breakdown of oil, localized sparking, partial discharge of oil, localized overheating or hot spots, etc. causes ... Over current relays with under voltage blocking 6.Zero sequence protection. 7.Negative phase sequence protection

What are the different types of faults in a transformer?

Description : What are the different types of faults in a transformer?

Last Answer : The internal faults include phase faults, ground faults, inter-turn faults, tap-changer failure, and leakage oil from tank. The external faults include system phase faults, system ground faults, over loads and over fluxing.

State the various types of unsymmetrical faults.

Description : State the various types of unsymmetrical faults.

Last Answer : Line to ground ,line to line and double line to ground faults

State the different types of faults.

Description : State the different types of faults.

Last Answer : Symmetrical faults and unsymmetrical faults and open conductor faults.

What are the causes of bus zone faults?

Description : What are the causes of bus zone faults?

Last Answer : Failure of support insulator resulting in earth fault Flashover across support insulator during over voltage Heavily polluted insulator causing flashover Earthquake, mechanical damage etc.

What are faults associated with an alternator?

Description : What are faults associated with an alternator?

Last Answer : (a) External fault or through fault (b) Internal fault 1, Short circuit in transformer winding and connection 2, Incipient or slow developing faults

What are the various faults that would affect an alternator?

Description : What are the various faults that would affect an alternator?

Last Answer : (a) Stator faults 1, Phase to phase faults 2, Phase to earth faults 3, Inter turn faults (b) 1, Earth faults 2, Fault between turns 3, Loss of excitation due to fuel failure (c) 1, Over ... rise, resulting in shattering of the turbine low pressure casing (d) 1, Fault on lines 2, Fault on busbars

What are the main types of stator winding faults?

Description : What are the main types of stator winding faults?

Last Answer : Fault between phase and ground; fault between phases and inter-turn fault involving turns of the same phase winding.

What are the various faults to which a turbo alternator is likely to be subjected?

Description : What are the various faults to which a turbo alternator is likely to be subjected?

Last Answer : Failure of steam supply; failure of speed; overcurrent; over voltage; unbalanced loading; stator winding fault .

How are faults are classified?

Description : How are faults are classified?

Last Answer : The faults are classified as shunt and series faults. The shunt faults are due to short circuits in conductors and the series faults are due to oped conductors.

Will main generator differential relay pick up for generator earth faults?

Description : Will main generator differential relay pick up for generator earth faults? 

Last Answer : No earth fault current limited to 5A, while differential setting is 10%. 

Earthquakes that occur along faults are created when ___________ a) Melted rock is erupted along the fault zone b) Stress builds up until rocks break c) The earth shifts and moves along fracture d) Answers b and c

Description : Earthquakes that occur along faults are created when ___________ a) Melted rock is erupted along the fault zone b) Stress builds up until rocks break c) The earth shifts and moves along fracture d) Answers b and c

Last Answer : d) Answers b and c

relays are used for phase faults on long line. (a) Impedance (b) Reactance (c) Either of the above (d) None of the above

Description : relays are used for phase faults on long line. (a) Impedance (b) Reactance (c) Either of the above (d) None of the above

Last Answer : (a) Impedance

Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Description : Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Last Answer : (d) all of the above

Large internal faults are protected by (a) merz price percentage differential protection (b) mho and ohm relays (c) horn gaps and temperature relays (d) earth fault and positive sequence relays

Description : Large internal faults are protected by (a) merz price percentage differential protection (b) mho and ohm relays (c) horn gaps and temperature relays (d) earth fault and positive sequence relays

Last Answer : (a) merz price percentage differential protection

An effective communication system employs a feedback mechanism in on (a) Make the necessary modification in the process (b) Understand more about the content (c) Find faults with the teacher (d) Find faults with the student

Description : An effective communication system employs a feedback mechanism in on (a) Make the necessary modification in the process (b) Understand more about the content (c) Find faults with the teacher (d) Find faults with the student

Last Answer : (a) Make the necessary modification in the process

. One of the more daunting challenges of managing a test project is that so many dependencies converge at test execution. One missing configuration file or hard ware device can render all your test results meaning less. You can end up with an entire platoon of testers sitting around for days. Who is responsible for this incident? A. Test managers faults only B. Test lead faults only C. Test manager and proj

Description : . One of the more daunting challenges of managing a test project is that so many dependencies converge at test execution. One missing configuration file or hard ware device can render all your test results ... incident? A. Test managers faults only B. Test lead faults only C. Test manager and proj

Last Answer : A. Test managers faults only

Distinguish software faults and software failures

Description : Distinguish software faults and software failures

Last Answer : Ans: In case of a failure, the software does not do what the user expects. A fault is a programming error that may or may not actually manifest as a failure. A fault can also be ... software is ported to a different hardware platform or a different compiler, or when the software gets extended.