Give the criteria for selection of distribution transformer as per IS:10028 (part-I) 1985.

Give the criteria for selection of distribution transformer as per IS:10028 (part-I) 1985.
by

1 Answer

Answer :

Criteria for selection of distribution transformer as per IS:10028 (part-I) 1985: 1) Total connected load. 2) Load Diversity factor. 3) Expected daily load curve. 4) Type of loads: (1 phase, 3 phase, 3 ph-4 wire system required) 5) Constant Losses. 6) Availability of space for transformer erection (indoor /outdoor). 7) A distance of loads from the transformer substation. 8) Times of low loads and maximum loads. 9) Future expansion plans or trends or forecasting. 10) Ambient conditions for deciding insulation class. 11) Tap changing requirement.

by

Related questions

Write selection criteria of distribution transformer with any four points.

Description : Write selection criteria of distribution transformer with any four points.

Last Answer : Selection Criteria for Distribution Transformer:  i) Ratings - The kVA ratings should comply with IS:2026 ( Part l )-1977*. The noload secondary voltage should be 433 volts for transformers to be ... is not necessary. vi) Cooling - The transformers covered in this group are generally ONAN, AN

Prepare troubleshooting chart for transformer as per IS- 10028-1981 (4 trouble) and Induction motor (4 troubles).

Description : Prepare troubleshooting chart for transformer as per IS- 10028-1981 (4 trouble) and Induction motor (4 troubles). 

Last Answer : Troubleshooting chart for I.M. :-  Sr.No Type of fault/abnormal conditions/Troubles Causes Remedies 1 Motor fails to start or not accelerate (Faults in starting supply ... 1.Unequal terminal voltage. 2. Single phase operation 3.Unbalanced voltage Rectify the Cause

Explain the criteria of selection of power transformer.

Description : Explain the criteria of selection of power transformer.

Last Answer : Selection Criteria for Power Transformer:  1) Ratings - The kVA ratings should comply with IS:10028 (Part l)-1985. The noload secondary voltage should be 5 % more than nominal voltage to ... ) Cooling - The transformers covered in this group are generally ONAN, ONAN/ONAF, ONAN/ONAF/OFAF.

State selection criteria of transducer.

Description : State selection criteria of transducer.

Last Answer : * Operating Principle : The transducers are selected on the basis of operating principle it may be resistive, inductive, capacitive, optical etc.  * Operating range : The range ... : The transducer should maintain input and output characteristic for the selected environmental condition. 

Give any four selection criteria for selecting network topology.

Description : Give any four selection criteria for selecting network topology.

Last Answer : Selection criteria for selecting network topology. 1. Size of the network & number of devices or nodes being connected. 2. Ease of configuration & installing. 3. The ease of adding new device in an ... hubs etc. 7. Costs involved. 8. Need of security. 9. Need of network administration. 

What is the selection criteria to shortlist candidates for admissions in top MBA colleges?

Description : What is the selection criteria to shortlist candidates for admissions in top MBA colleges?

Last Answer : MBA Admission 2020, has been stressful due to the present Covid-19 situation and lockdown in India. Students who had appeared for CAT, XAT, or GMAT had to have their admissions postponed. ... merit list. Students who haven’t appeared for the common entrance examinations may also apply for the cour

What are decision models? A. Project selection criteria B. Project selection methods C. Project selection committees D. Project resource and budget selection methods

Description : What are decision models?  A. Project selection criteria B. Project selection methods C. Project selection committees D. Project resource and budget selection methods

Last Answer : B. Project selection methods

Mathematical models using linear, dynamic, integer, or algorithm models are considered A. Project selection criteria B. A form of expert judgment C. Project selection methods D. A form of historical information

Description : Mathematical models using linear, dynamic, integer, or algorithm models are  considered  A. Project selection criteria B. A form of expert judgment C. Project selection methods D. A form of historical information

Last Answer : C. Project selection methods

From which of the following is selection criteria of robots. (A) Payload (B) Work volume (C) Speed (D) All of the above

Description : From which of the following is selection criteria of robots. (A) Payload (B) Work volume (C) Speed (D) All of the above

Last Answer : D

Explain the criteria of site selection for following cottage industry.

Description : Explain the criteria of site selection for following cottage industry.

Last Answer : i) Bricks Manufacturing: 1) The ground should be plain surface. 2) The site of brick manufacturing should be connected with road for transportation of materials. 3) Good brick earth should ... for installation of crushing plant. 7) It should have arrangement of electricity to operate crushers.

Explain the criteria for selection of construction materials for different civil engineering Structures on basis of their strength and durability

Description : Explain the criteria for selection of construction materials for different civil engineering Structures on basis of their strength and durability

Last Answer : The material must be selected for their ability to support the loads imposed by the building over the whole life of the building. An appropriate structural system and correct selection of ... of the building. The construction material should have sufficient strength to carry the prescribed load.

Describe the selection criteria for selecting stone for face work of building.

Description : Describe the selection criteria for selecting stone for face work of building. 

Last Answer : 1. Appearance: Stone to be used for construction should be decent in appearance and have uniform colour 2. Durability: A Good building stone should be durable i.e. it should resist atmospheric action ... it should not catch fire easily. 8. Seasoning: Stones should be well seasoned before use.

If you select a monitor in your class, which criteria will be followed by you in this selection? Options: A) On the basis of democratic(Through election) B) On the basis of physical make-up C) On the basis of superiority in the class D) On the basis of personal preference

Description : If you select a monitor in your class, which criteria will be followed by you in this selection? Options: A) On the basis of democratic(Through election) B) On the basis of physical make-up C) On the basis of superiority in the class D) On the basis of personal preference

Last Answer : A) On the basis of democratic(Through election) 

State the selection criteria for transducers

Description : State the selection criteria for transducers

Last Answer : 1. Operating range 2. Operating principle 3. Sensitivity 4. Accuracy 5. Frequency response and resonant frequency 6. Errors 7. Environmental compatibility 8. Usage and ruggedness. 9. ... . 10. Stability and Reliability 11. Loading effect 12. Static characteristics 13. Noise immunity

Write the criteria for selection of nozzle for given situation.

Description : Write the criteria for selection of nozzle for given situation.

Last Answer : Following are the situation for selection criteria of nozzle.  Situation first: It is used when the back pressure is equal or more than the critical pressure ratio. It is also used ... nozzle: Cross sectional area of nozzle first continuously decreases and then increases from entrance to exit.

Selection Criteria of PLC

Description : Selection Criteria of PLC

Last Answer : Selection criteria :- To select PLC for any particular application following points are to be considered. a) Type of PLC: Analog or Digital b) Number of inputs and outputs to PLC c) Operating voltage ... Type of memory of PLC g) Type of programming h) Reliability of PLC i) Flexibility of PLC

What are the criteria for selection of site for hydroelectric power plant?

Description : What are the criteria for selection of site for hydroelectric power plant?

Last Answer : Following Factors to be kept while site selecting for Hydro power plant:  1. It should be located where high rain fall occurs. 2. A large catchments area must be available to store water. 3. It ... 12. Cost of land should be less. 13. Skilled and unskilled man power should be available nearby.

State criteria for selection of contractor.

Description : State criteria for selection of contractor. 

Last Answer : Following the criteria for selection of contractor: 1. Contractor should be well reputed 2. Past experience of the Contractor 3. Contractor licenses should be valid 4. Works in hand of ... Material availability of the contractor. 6. Tax clearance certificate & financial power of contractor.

Give the specification of three phase transformer as per IS 1180(Part-1) 1989.

Description : Give the specification of three phase transformer as per IS 1180(Part-1) 1989. 

Last Answer : Specification of 3-phase transformer: 1) kVA rating of transformer 2) Voltage ratings for the primary and secondary voltages 3) HV and LV currents 4) Operating frequency of the transformer 5) % impedance of ... the manufacturer 16) Weight of core 17) Weight of winding 18) Volume of oil in litres.

How much line per turn does a zebco 33 classic 1985 reel retrive?

Description : How much line per turn does a zebco 33 classic 1985 reel retrive?

Last Answer : That depends on how much line is on the spool, if the spool isempty then each turn retrieves less line then when it is nearlyfull.

State the advantages of amorphous core type distribution transformer.

Description : State the advantages of amorphous core type distribution transformer.

Last Answer : Advantages of amorphous core type distribution transformer: 1) Increases efficiency of transformer as constant losses are reduced by 75 % compared to conventional transformers. 2) The material has high ... . 7) High Reliability. 8) Excellent short circuit capacity. 9) Less maintenance cost.

The market for heavy industrial equipment is concentrated in the West Midlands, so an equipment manufacturer has decided to employ a direct sales force in that region. Which factor most influenced this distribution channel selection? A)Buyer behaviour B)Product attributes C)Organisational objectives D)Environmental forces E)Market characteristics

Description : The market for heavy industrial equipment is concentrated in the West Midlands, so an equipment manufacturer has decided to employ a direct sales force in that region. Which factor ... A)Buyer behaviour B)Product attributes C)Organisational objectives D)Environmental forces E)Market characteristics

Last Answer : E)Market characteristics

The main criterion for selection of the size of a radial distribution system is

Description : The main criterion for selection of the size of a radial distribution system is

Last Answer : The main criterion for selection of the size of a radial distribution system is voltage drop

What are the limitations of the per capital income criteria of development ? -SST 10th

Description : What are the limitations of the per capital income criteria of development ? -SST 10th

Last Answer : (i) Per capital income is the average income of a country. (ii) Per capital income criteria takes into account only the economic aspect of life and ignores the social, aspect of life. (iii) ... because it is far behind than Kerala in literacy rate and has higher infant mortality rate than Kerala.

The acceptance criteria for precision studies as per bioanalytical method validation is? A. % RE must be within + 10% B. % RE must be within + 15% C. % RE must be within + 20% D. % RE must be within + 5%

Description : The acceptance criteria for precision studies as per bioanalytical method validation is? A. % RE must be within + 10% B. % RE must be within + 15% C. % RE must be within + 20% D. % RE must be within + 5%

Last Answer : B. % RE must be within + 15%

Latrines & urinals must be provided on these type of stations as per minimum essential facility criteria (a) A, B, C, D, E & F type station (b) A,B,C,D & E type station* (c) A,B,C & D type station (d) A, B & C type station

Description : Latrines & urinals must be provided on these type of stations as per minimum essential facility criteria (a) A, B, C, D, E & F type station (b) A,B,C,D & E type station* (c) A,B,C & D type station (d) A, B & C type station

Last Answer : (b) A,B,C,D & E type station*

Foot over bridge must be provided on the following type of stations as per minimum essential facility criteria (a) A, B, C, & D class station (b) A,B & C class station* (c) A, & B class station (d) Only A class station

Description : Foot over bridge must be provided on the following type of stations as per minimum essential facility criteria (a) A, B, C, & D class station (b) A,B & C class station* (c) A, & B class station (d) Only A class station

Last Answer : b) A,B & C class station*

Numbers of taps on each platform of ‘C’ category station as per norms of minimum essential facility criteria are (a) 6* (b) 8 (c) 12 (d) 15

Description : Numbers of taps on each platform of ‘C’ category station as per norms of minimum essential facility criteria are (a) 6* (b) 8 (c) 12 (d) 15

Last Answer : (a) 6*

Numbers of taps on each platform of ‘B’ category station as per norms of minimum essential facility criteria are (a) 6 (b) 8 (c) 12* (d) 15

Description : Numbers of taps on each platform of ‘B’ category station as per norms of minimum essential facility criteria are (a) 6 (b) 8 (c) 12* (d) 15

Last Answer : (c) 12*

Numbers of taps on each platform of ‘A’ category station as per norms of minimum essential facility criteria are (a) 6 (b) 8 (c) 12 (d) 15*

Description : Numbers of taps on each platform of ‘A’ category station as per norms of minimum essential facility criteria are (a) 6 (b) 8 (c) 12 (d) 15*

Last Answer : d) 15*

At what power maximum efficiency of power transformer and distribution transformer is designed

Description : At what power maximum efficiency of power transformer and distribution transformer is designed

Last Answer : Maximum efficiency of the transformer is attained at certain load factor (α) when core losses of transformer is equal to the copper losses. PCore loss = α ^2 X PCopper loss From the ... the day. Hence distribution transformers are designed to have maximum efficiency at 50% of the rated full load

What is the vector group of distribution transformer?

Description : What is the vector group of distribution transformer?

Last Answer : Dy11

Which type of connection is used in distribution transformer?

Description : Which type of connection is used in distribution transformer?

Last Answer : Distribution transformers are connected in delta-star. This arrangement requires 3 conductors in the high voltage side and 4 in the low voltage side, as well as it provides the star point conductor as a neutral point. This can serve single phase as well as three phase loads.

Why is an auto-transformer not used as a distribution transformer?

Description : Why is an auto-transformer not used as a distribution transformer?

Last Answer : The autotransformer cannot provide isolation between HV and LV side. Due to open circuit in the common portion, the voltage on the load side may shoot up to dangerously high voltage ... voltage on LV side is potentially dangerous. Hence the autotransformer cannot be used as distribution transformer

What are the salient features of distribution transformer?

Description : What are the salient features of distribution transformer?

Last Answer : 1. The distribution transformer will have low iron loss and higher value of copper loss 2. The capacity of transformers will be up to 500 KVA 3. The transformers will have plain walled ... with cooling tubes or radiators. 4. The leakage reactance and regulation will be low.

Why the efficiency of distribution transformer is 60 to 70 % and not 100%?

Description : Why the efficiency of distribution transformer is 60 to 70 % and not 100%?

Last Answer : Distribution transformer is designed for maximum efficiency at 60% to 70% load as it normally doesn't operate at full load all the time. Its load depends on distribution demand. Whereas power transformer ... efficiency at 100% load as it always runs at 100% load being near to generating station.

What are distribution transformer?

Description : What are distribution transformer?

Last Answer : The distribution transformer is used for the distribution of electrical energy at low voltage as less than 33KV in industrial purpose and 440v-220v in domestic purpose. It works at low efficiency at 60-70%, small size, easy in installation, having low magnetic losses & it is not always fully loaded.

What is the vector group of distribution transformer?

Description : What is the vector group of distribution transformer?

Last Answer : Dy11.  

Product of which labelling is voluntary .... v. Frost Free Refrigerator.C) Colour TV D) Distribution TransformeR vi. Ceiling Fans

Description : Product of which labelling is voluntary .... v. Frost Free Refrigerator.C) Colour TV D) Distribution TransformeR vi. Ceiling Fans

Last Answer : CEILING FANS

Appliances need to have BEE star rating label are…… A) Frost free refrigerator. C) Color TV B) Distribution Transformer. D) All of the above

Description : Appliances need to have BEE star rating label are…… A) Frost free refrigerator. C) Color TV B) Distribution Transformer. D) All of the above.

Last Answer : all the above

Overfluxing protection is recommended for (a) distribution transformer (b) generator transformer of the power plant (c) auto-transformer of the power plant (d) station transformer of the power plant

Description : Overfluxing protection is recommended for (a) distribution transformer (b) generator transformer of the power plant (c) auto-transformer of the power plant (d) station transformer of the power plant

Last Answer : (b) generator transformer of the power plant

Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

Explain how technical losses can be reduced by use of energy efficient transformer in Transmission and Distribution system.

Description : Explain how technical losses can be reduced by use of energy efficient transformer in Transmission and Distribution system.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

The maximum efficiency of a distribution transformer is?

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

In a power or distribution transformer about 10 percent end turns are heavily insulated?

Last Answer : In a power or distribution transformer about 10 percent end turns are heavily insulated to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns.

What five elements are part of all well defined evaluation criteria?

Description : What five elements are part of all well defined evaluation criteria?

Last Answer : T

Which one of the following is not a part of the attest process? a. Evaluating evidence against objective criteria b. Gathering evidence about assertions c. Proving the accuracy of the books and records d. Communicating the conclusions reached

Description : Which one of the following is not a part of the attest process? a. Evaluating evidence against objective criteria b. Gathering evidence about assertions c. Proving the accuracy of the books and records d. Communicating the conclusions reached

Last Answer : Proving the accuracy of the books and records

Evaluating testability of the requirements and system are a part of which phase:- a) Test Analysis and Design b) Test Planning and control c) Test Implementation and execution d) Evaluating exit criteria and reporting Q4. One of the fields on a form contains a text box which accepts alphabets in lower or upper case. Identify the invalid Equivalence class value.

Description : Evaluating testability of the requirements and system are a part of which phase:- a) Test Analysis and Design b) Test Planning and control c) Test Implementation and execution d) Evaluating ... text box which accepts alphabets in lower or upper case. Identify the invalid Equivalence class value.

Last Answer : a) Test Analysis and Design

How do I flip the viewfinder image on an old (~1985) Panasonic video camera, Model #PK-980?

Description : How do I flip the viewfinder image on an old (~1985) Panasonic video camera, Model #PK-980?

Last Answer : answer:Here is an online manual for that camcorder. Edit* It’s a service to find manuals, maybe it will work, I’m still looking.

Where can I sell my Air Jordans of 1985 other than eBay?

Description : Where can I sell my Air Jordans of 1985 other than eBay?

Last Answer : Someone on ask-public, their name escapes me now, buys an sells vintage shoes. I’ll try to find the thread where it was mentioned or they see this. Hopefully, they can help.