The maximum depth from which a centrifugal pump can draw water is (A) Dependent on the speed of the pump (B) Dependent on the power of the pump (C) 34 feet (D) 150 feet

The maximum depth from which a centrifugal pump can draw water is
(A) Dependent on the speed of the pump
(B) Dependent on the power of the pump
(C) 34 feet
(D) 150 feet
by

1 Answer

Answer :

(C) 34 feet
by

Related questions

Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37

Last Answer : (C) 8

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Last Answer : (A) 0.5

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Last Answer : (A) 2

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Description : The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Last Answer : (D) All the above

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Last Answer : (C) Axial flow

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

Specific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal pump relates it with another pumphaving the(A) Dynamic similarity(B) Same efficiency(C) Same speed(D) Geometrical similarity

Description : Specific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal ... another pumphaving the(A) Dynamic similarity(B) Same efficiency(C) Same speed(D) Geometrical similarity

Last Answer : (A) Dynamic similarity

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Last Answer : (B) Centrifugal

A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump (A) Develops a lower head (B) Capacity is reduced (C) Requires more power (D) All (A), (B) and (C)

Description : A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump (A) Develops a lower head (B) Capacity is reduced (C) Requires more power (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump used to pump water is used to pump an oil withspecific gravity of 0.8 at the same rate. The power consumption will now (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict

Description : A centrifugal pump used to pump water is used to pump an oil withspecific gravity of 0.8 at the same rate. The power consumption will now (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict

Last Answer : (B) Decrease

Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Description : Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Last Answer : (D) N3D5

If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Description : If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Last Answer : B) 23/2

The efficiency of a centrifugal pump is maximum when its blades are :

Description : The efficiency of a centrifugal pump is maximum when its blades are : (A) straight (B) bent forward (C) bent backward (D) bent forward first and then backward

Last Answer : The efficiency of a centrifugal pump is maximum when its blades are : bent backward

The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option D

The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option C

Boiler feed water pump is usually a __________ pump.(A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Last Answer : (C) Multistage centrifugal

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Description : A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Last Answer : (A) Less head & capacity

Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Last Answer : (B) Centrifugal

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

Centrifugal pump made of pyrex or glass can't be used to pump (A) Milk and fruit juices (B) Alkaline solutions (C) Dilute H2SO4 at room temperature (D) Brine

Description : Centrifugal pump made of pyrex or glass can't be used to pump (A) Milk and fruit juices (B) Alkaline solutions (C) Dilute H2SO4 at room temperature (D) Brine

Last Answer : (B) Alkaline solutions

For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Last Answer : (B) Diaphragm

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid(C) Equal to the vapour pressure of the liquid(D) Less than barometric pressure

Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure

Last Answer : (A) Greater than the vapour pressure of the liquid

Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Description : Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Last Answer : (D) Increase the discharge

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure(C) Low suction pressure(D) High suction velocity

Description : What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure (C) Low suction pressure (D) High suction velocity

Last Answer : (C) Low suction pressure

A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Description : Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Last Answer : (B) ηm = ηv . ηma

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Description : A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Last Answer : (C) Positive acting rotary