A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

A mono pump is a __________ pump.
(A) Centrifugal
(B) Piston
(C) Positive acting rotary
(D) A group of vacuum
by

1 Answer

Answer :

(C) Positive acting rotary
by

Related questions

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Last Answer : (A) Vane

__________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Description : __________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Last Answer : (C) Plunger

For separation of sugar solution from settled out mud, we use a __________ filter. (A) Sparkler (B) Plate and frame (C) Centrifugal (D) Rotary drum vacuum

Description : For separation of sugar solution from settled out mud, we use a __________ filter. (A) Sparkler (B) Plate and frame (C) Centrifugal (D) Rotary drum vacuum

Last Answer : (C) Centrifugal

Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Description : Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Last Answer : (B) Gear

In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Last Answer : ANSWER : C

__________ pumps are a group of vacuum pumps. (A) Hyster (B) Sump (C) Mono (D) Submerged

Description : __________ pumps are a group of vacuum pumps. (A) Hyster (B) Sump (C) Mono (D) Submerged

Last Answer : (A) Hyster

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Last Answer : (A) Turbine

Bucket type sprayer consist of: i) Single and double acting pump c) Plunger type pump j) Centrifugal pump d) All are correct

Description : Bucket type sprayer consist of: i) Single and double acting pump c) Plunger type pump j) Centrifugal pump d) All are correct

Last Answer : Single and double acting pump

Bucket type sprayer consist of: A. Single and double acting pump B. Centrifugal pump C. Plunger type pump D. All are correct

Description : Bucket type sprayer consist of: A. Single and double acting pump B. Centrifugal pump C. Plunger type pump D. All are correct

Last Answer : Single and double acting pump

Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid(C) Equal to the vapour pressure of the liquid(D) Less than barometric pressure

Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure

Last Answer : (A) Greater than the vapour pressure of the liquid

Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Description : Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Last Answer : (A) Is a positive displacement pump

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Description : Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Last Answer : 2

The speed of a rotary drum vacuum filter may be about __________ rpm. (A) 1 (B) 50 (C) 100 (D) 500

Description : The speed of a rotary drum vacuum filter may be about __________ rpm. (A) 1 (B) 50 (C) 100 (D) 500

Last Answer : (A) 1

__________ is used for producing a thick suspension from a thin slurry. (A) Cartridge filter (B) Rotary drum vacuum filter (C) Pressure filter thickener (D) Plate and frame filter press

Description : __________ is used for producing a thick suspension from a thin slurry. (A) Cartridge filter (B) Rotary drum vacuum filter (C) Pressure filter thickener (D) Plate and frame filter press

Last Answer : (C) Pressure filter thickener

For classification of potable (drinking) water, we use a __________ filter. (A) Gravity sand (B) Plate and frame (C) Vacuum leaf (D) Rotary vacuum

Description : For classification of potable (drinking) water, we use a __________ filter. (A) Gravity sand (B) Plate and frame (C) Vacuum leaf (D) Rotary vacuum

Last Answer : (A) Gravity sand

For removal of very small amounts of precipitate from large volume of water, the most suitable filter is the __________ filter. (A) Plate & frame (B) Shell & lea(C) Sand(D) Rotary vacuum

Description : For removal of very small amounts of precipitate from large volume of water, the most suitable filter is the __________ filter. (A) Plate & frame (B) Shell & lea (C) Sand (D) Rotary vacuum

Last Answer : (C) Sand

Vacuum is applied in __________ zone, in case of a general type continuous rotary drum vacuum filter(A) Filtering(B) Washing(C) Drying(D) All (A), (B) & (C).

Description : Vacuum is applied in __________ zone, in case of a general type continuous rotary drum vacuum filter. (A) Filtering (B) Washing (C) Drying (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The controlling resistance in a rotary drum vacuum filter is the __________ resistance.(A) Piping (B) Cake (C) Filter medium (D) None of these

Description : The controlling resistance in a rotary drum vacuum filter is the __________ resistance. (A) Piping (B) Cake (C) Filter medium (D) None of these

Last Answer : (B) Cake

The most suitable filter for the removal of very small amount of precipitate from very large volumes of water is the __________ filter. (A) Vacuum (B) Sand (C) Plate & frame (D) Rotary

Description : The most suitable filter for the removal of very small amount of precipitate from very large volumes of water is the __________ filter. (A) Vacuum (B) Sand (C) Plate & frame (D) Rotary

Last Answer : (B) Sand

Filtrate flow rate in case of a rotary drum vacuum filter (in which Rm < < Rc ) is proportional to __________ and the cycle time (where, μ = filtrate viscosity Rm = filter medium resistance Rc = cake resistance). (A) √μ (B) 1/√μ (C) 1/μ (D) 1/μ

Description : Filtrate flow rate in case of a rotary drum vacuum filter (in which Rm < < Rc ) is proportional to __________ and the cycle time (where, μ = filtrate viscosity Rm = filter medium resistance Rc = cake resistance). (A) √μ (B) 1/√μ (C) 1/μ (D) 1/μ

Last Answer : (B) 1/√μ

Calcium ammonium nitrate (a fertiliser) is dried in a __________ dryer. (A) Rotary (B) Vacuum (C) Tunnel (D) Tray

Description : Calcium ammonium nitrate (a fertiliser) is dried in a __________ dryer. (A) Rotary (B) Vacuum (C) Tunnel (D) Tray

Last Answer : (A) Rotary

Drying of refractory is normally carried out in a __________ dryer. (A) Open pan (B) Tray (C) Rotary vacuum (D) Truck/tunnel

Description : Drying of refractory is normally carried out in a __________ dryer. (A) Open pan (B) Tray (C) Rotary vacuum (D) Truck/tunnel

Last Answer : (D) Truck/tunnel

Large quantity of silica gel is normally dried in a __________ dryer. (A) Freeze (B) Through circulation (C) Rotary vacuum (D) Tray

Description : Large quantity of silica gel is normally dried in a __________ dryer. (A) Freeze (B) Through circulation (C) Rotary vacuum (D) Tray

Last Answer : (B) Through circulation

Large scale drying of wheat is done in a __________ dryer. (A) Fluidised bed (B) Spouted bed (C) Tray (D) Vacuum rotary

Description : Large scale drying of wheat is done in a __________ dryer. (A) Fluidised bed (B) Spouted bed (C) Tray (D) Vacuum rotary

Last Answer : (B) Spouted bed

Rotary vacuum pumps can reduce the absolute pressure to as low as __________ mm Hg. (A) 1 (B) 0.1 (C) 0.01 (D) 0.001

Description : Rotary vacuum pumps can reduce the absolute pressure to as low as __________ mm Hg. (A) 1 (B) 0.1 (C) 0.01 (D) 0.001

Last Answer : (C) 0.01

Why Centrifugal Pump Is Not Called As A Positive Displacement Type Of Pump?

Description : Why Centrifugal Pump Is Not Called As A Positive Displacement Type Of Pump?

Last Answer : The centrifugal has varying flow depending on pressure or head, whereas the Positive Displacement pump has more or less constant flow regardless of pressure. Likewise viscosity is constant for ... pump has more or less constant efficiency, where centrifugal pump has varying efficiency rate.

A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Description : A ____ pump consists of a reciprocating or rotating cavity between two lobes or gears and a rotor. a. positive c. negative b. centrifugal d. hand

Last Answer : a. positive

The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Description : The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Last Answer : Ans: d

Forces acting on a particle settling in fluid are __________ forces. (A) Gravitational & buoyant (B) Centrifugal & drag (C) Gravitational or centrifugal buoyant drag (D) External, drag & viscous

Description : Forces acting on a particle settling in fluid are __________ forces. (A) Gravitational & buoyant (B) Centrifugal & drag (C) Gravitational or centrifugal buoyant drag (D) External, drag & viscous

Last Answer : (C) Gravitational or centrifugal buoyant drag

For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder

Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Last Answer : (B) Centrifugal

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Last Answer : (B) Diaphragm

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

Boiler feed water pump is usually a __________ pump.(A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Last Answer : (C) Multistage centrifugal

High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Last Answer : (C) Axial flow

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Description : Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal

Last Answer : (D) Centrifugal

For the transfer of solution of thick slurry, the pump used is a __________ pump(A) Reciprocating(B) Gear(C) Diaphragm(D) Centrifugal.

Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal

Last Answer : (C) Diaphragm

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric