Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these
Last Answer : (B) Centrifugal
Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these
Last Answer : (A) Axial
Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions
Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow
Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump
Last Answer : (C) Gear pump
Description : Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps
Last Answer : (A) Axial flow pump
Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these
Last Answer : (D) None of these
Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1
Last Answer : (A) 0.5
Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5
Last Answer : (A) 2
Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750
Last Answer : (A) 500
Description : The specific speed of a centrifugal compressor is generally A. less than that of reciprocating compressor B. independent of compressor type, but depends only on size of compressor C. higher ... axial compressor D. more than specific speed of reciprocating compressor but less than axial compressor
Last Answer : ANSWER : C
Description : Specific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal ... another pumphaving the(A) Dynamic similarity(B) Same efficiency(C) Same speed(D) Geometrical similarity
Last Answer : (A) Dynamic similarity
Description : In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan
Last Answer : (B) Turbine
Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor
Last Answer : (B) Blower
Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these
Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)
Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)
Description : Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?
Last Answer : Isentropic efficiency of axial flow compressor is higher.
Description : Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor
Last Answer : (i) Reciprocating and rotary air compressor: Sr. No. Reciprocating air compressor Rotary air compressor 1 It is having to and fro motion. It is having rotary ... I.C. engine and for refrigerants and industrial gases. Used universally with large gas turbine.
Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these
Last Answer : (A) Open
Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)
Last Answer : (C) Mounting of two or more impellers in series on a single shaft
Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these
Last Answer : (A) Turbine
Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston
Last Answer : (A) Diffusion
Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these
Last Answer : (C) Avoid chances of separation inside the impeller
Description : With increasing flow rate, the hydraulic efficiency of a centrifugal pump (A) Monotonically decreases (B) Decreases and then increases (C) Remains constant (D) Increases and then decreases
Last Answer : (A) Monotonically decreases
Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)
Last Answer : (A) Back flow of fluid in the event of stoppage of pump
Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these
Last Answer : (B) Loss of kinetic head
Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe
Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump
Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed
Last Answer : (B) Head varies as the square of speed
Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : C) Both (A) and (B)
Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N
Last Answer : (A) D = 1840 H0.5 /N
Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid
Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller
Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor
Last Answer : (A) Cavitation
Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)
Description : The maximum depth from which a centrifugal pump can draw water is (A) Dependent on the speed of the pump (B) Dependent on the power of the pump (C) 34 feet (D) 150 feet
Last Answer : (C) 34 feet
Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal
Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute
Last Answer : (A) Electromagnetic
Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic
Last Answer : (B) Diaphragm
Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction
Last Answer : (A) Manometric
Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm
Last Answer : (C) Multistage centrifugal
Description : A hydraulic ram acts as a/an __________ pump. (A) Centrifugal (B) Reciprocating (C) Impulse (D) Parallel cylinder
Last Answer : (C) Impulse
Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser
Last Answer : (A) Single stage vertical
Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear
Last Answer : (A) Centrifugal
Description : A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum
Last Answer : (C) Positive acting rotary
Description : Molten soap mass is transported by a __________ pump. (A) Diaphragm (B) Reciprocating (C) Gear (D) Centrifugal
Last Answer : (D) Centrifugal
Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal
Last Answer : (C) Diaphragm
Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall
Description : Maximum theoretical suction lift for water at 15°C by a centrifugal pump is 34 ft. The same for water at 90°C will be __________ ft. (A) 40 (B) 34 (C) 8 (D) 37
Last Answer : (C) 8
Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger
Last Answer : (A) Vane
Description : Priming is needed in a __________ pump. (A) Reciprocating (B) Gear (C) Centrifugal (D) Diaphragm
Last Answer : (C) Centrifugal