For centrifugal pumps (A) Initial cost is low (B) Limited space is required (C) The discharge obtained is steady and non-pulsating (D) All the above

For centrifugal pumps 

(A) Initial cost is low 

(B) Limited space is required 

(C) The discharge obtained is steady and non-pulsating 

(D) All the above 

by

1 Answer

Answer :

(D) All the above 

by

Related questions

Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Description : Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Last Answer : (D) Can be run with discharge line valve closed for a short interval

Reciprocating pumps (A) Are not suitable for variable heads (B) Are four times costlier than centrifugal pumps (C) Are not suitable for pumping water containing sediments (D) Single stroke produce pulsating flow

Description : Reciprocating pumps  (A) Are not suitable for variable heads  (B) Are four times costlier than centrifugal pumps  (C) Are not suitable for pumping water containing sediments  (D) Single stroke produce pulsating flow 

Last Answer : (A) Are not suitable for variable heads 

Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Description : Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Last Answer : (C) Higher capital &maintenance cost

Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump(B) Reciprocating pump(C) Gear pump(D) Axial flow pump

Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump

Last Answer : (C) Gear pump

Multistage centrifugal pumps are generally used for (A) High head (B) Low head but high discharge (C) Highly viscous liquid (D) Slurries of high solid concentration

Description : Multistage centrifugal pumps are generally used for (A) High head (B) Low head but high discharge (C) Highly viscous liquid (D) Slurries of high solid concentration

Last Answer : (A) High head

The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*

Last Answer : e) all of the above*

The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Description : The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Description : Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads

Last Answer : (B) High capacity at low heads

Two identical pumps, each capable of delivering 0.2 cumec, against a head of 30 m, are connected in parallel. The resulting discharge is : a) 0.4 cumec against a head of 30 m b) 0.4 cumec against a head of 60 m c) 0.2 cumec against a head of 30 m d) 0.2 cumec against a head of 60 m

Description : Two identical pumps, each capable of delivering 0.2 cumec, against a head of 30 m, are connected in parallel. The resulting discharge is : a) 0.4 cumec against a head of 30 m b) 0.4 cumec against a head of 60 m c) 0.2 cumec against a head of 30 m d) 0.2 cumec against a head of 60 m

Last Answer : a) 0.4 cumec against a head of 30 m

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Description : Which of the following pumps in used to pump sewage solids with liquid sewage without clogging the pump is? A. Centrifugal pump B. Pneumatic ejector C. Reciprocating pump D. None of these

Last Answer : ANS: A

Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Description : Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Last Answer : (C) Are not subject to air binding

Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Description : Most of the centrifugal pumps used in chemical plants are usually __________ driven. (A) Steam (B) Diesel engine (C) Electric motor (D) Gas turbine

Last Answer : (C) Electric motor

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Last Answer : (C) Less than liquid vapor pressure

Why Cavitation Will Occur In Centrifugal Pumps And Not In Displacement Pumps?

Description : Why Cavitation Will Occur In Centrifugal Pumps And Not In Displacement Pumps?

Last Answer : The formation of cavities (or bubbles) is induced by flow separation, or non-uniform flow velocities, inside a pump casing. In centrifugal pumps the eye of the pump impeller is smaller than ... to increase in temperature in impeller. This air bubbles are transmitted to pump which forms cavitation.

Chemical engineering plant cost index is used for finding the present cost of a particular chemical plant, if the cost of similar plant at some time in the past is known. The present cost of the plant = original cost × (index value at present/ index value at time original cost was obtained). The most major component of this cost index is (A) Fabricated equipment and machinery (B) Process instruments and control (C) Pumps and compressor (D) Electrical equipments and material

Description : Chemical engineering plant cost index is used for finding the present cost of a particular chemical plant, if the cost of similar plant at some time in the past is known. The present cost of ... (B) Process instruments and control (C) Pumps and compressor (D) Electrical equipments and material

Last Answer : (A) Fabricated equipment and machinery

. In a backward feed multiple effect evaporator (A) Feed is introduced in the first effect (B) Feed flows from low pressure to high pressure (C) No pumps are required between successive effects (D) None of these

Description : . In a backward feed multiple effect evaporator (A) Feed is introduced in the first effect (B) Feed flows from low pressure to high pressure (C) No pumps are required between successive effects (D) None of these

Last Answer : (B) Feed flows from low pressure to high pressure

The discharge Q = 2 /2.3 log10 (R/rw) for the confined tube well is obtained from (A) Thiem's formula (B) Darcy's formula (C) Tolman's formula (D) Dupuits formula

Description : The discharge Q = 2 /2.3 log10 (R/rw) for the confined tube well is obtained from  (A) Thiem's formula  (B) Darcy's formula  (C) Tolman's formula  (D) Dupuits formula 

Last Answer : (D) Dupuits formula 

The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If the working depression head of the well is 3 m, the minimum diameter of the well, is (A) 2 m (B) 2.25 m (C) 2.50 m (D) 3.00 m

Description : The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If  the working depression head of the well is 3 m, the minimum diameter of the well, is  (A) 2 m  (B) 2.25 m  (C) 2.50 m  (D) 3.00 m 

Last Answer : (D) 3.00 m 

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

For a catchment area of 120 km², the equilibrium discharge in m3/hour of a Scurve obtained by the summation of 6 hour unit hydro graph is (A) 0.2 × 106 (B) 0.6 × 106 (C) 2.4 × 106 (D) 7.2 × 10

Description : For a catchment area of 120 km², the equilibrium discharge in m3/hour of a Scurve obtained by the summation of 6 hour unit hydro graph is (A) 0.2 × 106 (B) 0.6 × 106 (C) 2.4 × 106 (D) 7.2 × 10

Last Answer : Answer: Option A

Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Description : Volute type of casing is provided in a centrifugal pump to (A) Convert velocity head to pressure head (B) Convert pressure head to velocity head (C) Reduce the discharge fluctuation (D) Increase the discharge

Last Answer : (D) Increase the discharge

Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Description : Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict

Description : If the discharge of a centrifugal pump is throttled, then its suction lift (A) Increases (B) Decreases (C) Remains unchanged (D) Data insufficient to predict

Last Answer : (A) Increases

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

Foot valves are provided in the suction line of a centrifugal pump to (A) Avoid priming, every time we start the pump (B) Remove the contaminant present in the liquid (C) Minimise the fluctuation in discharge (D) Control the liquid discharge

Description : Foot valves are provided in the suction line of a centrifugal pump to (A) Avoid priming, every time we start the pump (B) Remove the contaminant present in the liquid (C) Minimise the fluctuation in discharge (D) Control the liquid discharge

Last Answer : (A) Avoid priming, every time we start the pump

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Description : Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Last Answer : (A) Increase

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

Why The Centrifugal Pump Is Called High Discharge Pump?

Description : Why The Centrifugal Pump Is Called High Discharge Pump?

Last Answer : Centrifugal pump is a kinetic device. The centrifugal pump uses the centrifugal force to push out the fluid. So the liquid entering the pump receives kinetic energy from the rotating impeller. The centrifugal ... following formulae: Centrifugal force F= (M*V2)/R. Where, M-Mass V-Velocity R-Radius

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

Advantage of a clamp compared to a kiln for burning bricks is that (A) It takes less time for burning (B) It gives more output of first class bricks (C) It has less initial cost (D) It is suitable when bricks are required in large numbers

Description : Advantage of a clamp compared to a kiln for burning bricks is that (A) It takes less time for burning (B) It gives more output of first class bricks (C) It has less initial cost (D) It is suitable when bricks are required in large numbers

Last Answer : Answer: Option C

Accuracy of elevation of various points obtained from contour map is limited to (A) ½ of the contour interval (B) ¼ th of the contour interval (C) rd of the contour interval (D) th of the contour interval

Description : Accuracy of elevation of various points obtained from contour map is limited to (A) ½ of the contour interval (B) ¼ th of the contour interval (C) rd of the contour interval (D) th of the contour interval

Last Answer : (A) ½ of the contour interval

The space time is equivalent to the holding time in a steady state mixed reactor for (A) Non-isothermal gas reaction (B) Variable fluid density systems (C) Constant fluid density systems(D) Gas reactions with changing number of moles

Description : The space time is equivalent to the holding time in a steady state mixed reactor for (A) Non-isothermal gas reaction (B) Variable fluid density systems (C) Constant fluid density systems (D) Gas reactions with changing number of moles

Last Answer : (C) Constant fluid density systems

The steady-state fault current during a 3 phase terminal fault on a generator is limited by:

Description : The steady-state fault current during a 3 phase terminal fault on a generator is limited by: (1) Transient reactance of the generator (2) Sub-transient reactance of the generator (3) Synchronous reactance of the generator (4) DC off—set during the instant of the fault

Last Answer : 1

A centrifugal filtration unit operating at a rotational speed of w has inner surface of the liquid (density ρL) located at a radial distance R from the axis of rotation. The thickness of the liquid film is δ and no cake is formed. The initial pressure drop during filtration is (A) ½w 2 . R 2 . ρL (B) ½w 2 . δ 2 . ρL (C) ½w 2 . δρL (2R + δ) (D) ½w 2 . R . ρL(R + 2δ)

Description : A centrifugal filtration unit operating at a rotational speed of w has inner surface of the liquid (density ρL) located at a radial distance R from the axis of rotation. The thickness of the liquid film is δ and no cake is formed. The ... . ρL (C) ½w 2 . δρL (2R + δ) (D) ½w 2 . R . ρL(R + 2δ)

Last Answer : (C) ½w 2 . δρL (2R + δ)

Right now my vision is pulsating slightly up and down, almost twitching. My eyes aren't actually moving, and I can't find anything on google about it. It happens every six months or so. Any idea what it is or what to do?

Description : Right now my vision is pulsating slightly up and down, almost twitching. My eyes aren't actually moving, and I can't find anything on google about it. It happens every six months or so. Any idea what it is or what to do?

Last Answer : Could be a blood vessel in your eye, maybe a blood clot? Try checking with an eye doctor

What could be wrong in my ears, I feel pulsating inside?

Description : What could be wrong in my ears, I feel pulsating inside?

Last Answer : You should get your ears tested at a hospital by a professional.

What is the English language of simple pulsating motion ?

Description : What is the English language of simple pulsating motion ?

Last Answer : English simple harmonic motion.

What causes pulsating buttocks?

Description : What causes pulsating buttocks?

Last Answer : Hi! It can happen due to several different things, including lots of exercises, sitting too many hours, or even standing up for extended periods of time. If you are also undergoing lots of stress, ... he will be able to help you better understand the issue and help you get rid of the discomfort.