Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger
Last Answer : (A) Vane
Description : Continuous injection system usually has a) plunger pump b) rotary pump c) gear pump d) vane pump
Last Answer : Answer: b Explanation: In common use continuous injection system usually has rotary pump.
Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser
Last Answer : (A) Single stage vertical
Description : The type of pump used for lifting large quantity of sewage is a __________ pump. (A) Gear (B) Centrifugal (C) Reciprocating (D) Plunger
Last Answer : (B) Centrifugal
Description : The pump is used in power-operated sprayer is: A. Plunger type B. Diaphragm type C. Gear type D. Piston type
Last Answer : Gear type
Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston
Last Answer : (A) Diffusion
Description : A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum
Last Answer : (C) Positive acting rotary
Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure
Last Answer : (C) Less than liquid vapor pressure
Description : Pressure of CO2 gas (which is a coolant) in the Calder-Hall nuclear reactor is __________ kgf/cm2 . (A) 0.2 (B) 7 (C) 35 (D) 50
Last Answer : (B) 7
Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C
Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C
Description : Bucket type sprayer consist of: i) Single and double acting pump c) Plunger type pump j) Centrifugal pump d) All are correct
Last Answer : Single and double acting pump
Description : The pump used in airplane sprayers: A. Dentrifugal and gear pump B. Gear and Diaphragm pump C. Diaphragm and centrifugal pump D. Plunger and centrifugal pump
Last Answer : Dentrifugal and gear pump
Description : Bucket type sprayer consist of: A. Single and double acting pump B. Centrifugal pump C. Plunger type pump D. All are correct
Description : Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are (A) 5°C and 1 kgf/cm2 (B) - 20°C and 1 kgf/cm2 (C) 0°C and 1 kgf/cm2 (D) 0°C and 3 kgf/cm
Last Answer : (A) 5°C and 1 kgf/cm
Description : Temperature and gage pressure maintained during the manufacture of hot SBR (styrene butadiene rubber) are (A) 50°C and 3 - 4 kg/cm2 (B) 50°C and 1 kgf/cm2 (C) 250°C and 10 kgf/cm2 (D) 250°C and 1 kgf/cm
Last Answer : (A) 50°C and 3 - 4 kg/cm
Description : Low pressure Zeigler process of polythene manufacture (A) Employs a pressure of 30 kgf/cm2 (B) Achieves an yield of 95-98% based on ethylene (C) Produces very low density polythene (D) Does not use any catalyst for polymerisation
Last Answer : (B) Achieves an yield of 95-98% based on ethylene
Description : Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C
Last Answer : (B) 15-45 Kgf/cm2 & 450-550°C
Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline
Last Answer : (B) Suppress coke formation
Description : Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C
Last Answer : (A) 4 kgf/cm2 & 500°C
Description : Normal temperature and pressure (N.T.P.) corresponds to (A) 0°C and 760 mm Hg (B) 15°C and 760 mm Hg (C) 20°C and 760 mm Hg (D) 0°C and 1 kgf/cm2
Last Answer : (C) 20°C and 760 mm Hg
Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump
Last Answer : ANSWER : C
Description : Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump
Last Answer : (B) Gear
Description : A hydraulic accumulator comprises of (A) A storage device and a control valve (B) A cylinder and a plunger (C) Two pistons and two cylinders (D) A storage tank and a ram pump
Last Answer : (B) A cylinder and a plunger
Description : One barometric pressure or 1 atmospheric pressure is equal to (a) 1 kgf/cnr2 (b) 1.033 kgf/cm2 (c) 0 kgf/cm2 (d) 1.0197 kgf/cm2 (e) 100 kgf/cm2.
Last Answer : Answer : b
Description : Which of the statement is True for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The ... operated with inlet-guide vane control d) The compressor should not be operated close to the surge point
Last Answer : d) The compressor should not be operated close to the surge point
Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these
Last Answer : (B) Higher than
Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C
Last Answer : (A) 7 kgf/cm2 and 70 °C
Description : Operating condition in the electrical dehydrators for crude oil is about (A) 6.5 kgf/Cm2 & 95°C (B) 1 atm. & 110 °C (C) 20 kgf/cm2 & 110°C (D) 50 atm. and 150°C
Last Answer : (A) 6.5 kgf/Cm2 & 95°C
Description : For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head of 30 m. The minimum required horse power, is (A) 10 H.P. (B) 15 H.P. (C) 18 H.P. (D) 20 H.P.
Last Answer : (D) 20 H.P.
Description : Pump used for the transportation of molten sodium in a fast breader reactor is a/an __________ pump. (A) Reciprocating (B) Plunger (C) Electromagnetic (D) Gear
Last Answer : (C) Electromagnetic
Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute
Last Answer : (A) Electromagnetic
Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction
Last Answer : (A) Manometric
Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Net positive suction head (NPSH) of a centrifugal pump must be (A) Greater than the vapour pressure of the liquid (B) Less than the vapour pressure of the liquid (C) Equal to the vapour pressure of the liquid (D) Less than barometric pressure
Last Answer : (A) Greater than the vapour pressure of the liquid
Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)
Last Answer : (A) Back flow of fluid in the event of stoppage of pump
Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid
Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller
Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature
Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature
Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head
Last Answer : (A) Less than the vapour pressure of the liquid at that temperature
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : I kgf/cm2 is equal to (a) 760 mm Hg (b) zero mm Hg (c) 735.6 mm Hg (d) 1 mm Hg (e) l00 mm Hg.
Last Answer : Answer : c
Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these
Last Answer : (A) Turbine
Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these
Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder
Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall
Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum
Last Answer : (A) Reciprocating
Description : Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)
Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N
Last Answer : (A) D = 1840 H0.5 /N
Description : The vent valve provided in a liquid handling centrifugal pump is (A) Generally a needle valve (B) Used to release any gases that might be vapour locking the pump (C) Helpful in easy removal of samples (D) All (A), (B) and (C)
Description : Foot valves are provided in the suction line of a centrifugal pump to (A) Avoid priming, every time we start the pump (B) Remove the contaminant present in the liquid (C) Minimise the fluctuation in discharge (D) Control the liquid discharge
Last Answer : (A) Avoid priming, every time we start the pump
Description : Self-priming centrifugal pump can be used for (A) Booster service (B) Pumping liquid fertilisers (e.g. liquid NH3 ) (C) Pumping industrial wastes (D) All (A), (B) and (C)