The equivalent diameter for fluid flow through square cross section channel of side 'x', for pressure drop calculation purpose is given by (A) 4x (B) 2x (C) x (D) √x

The equivalent diameter for fluid flow through square cross section
channel of side 'x', for pressure drop calculation purpose is given by
(A) 4x
(B) 2x
(C) x
(D) √x
by

1 Answer

Answer :

(C) x
by

Related questions

The equivalent diameter for pressure drop calculation for a duct of square cross-section is given by (where, x = each side of the square duct). (A) x (B) √(πx) (C) √(2x) (D) √(x/2)

Description : The equivalent diameter for pressure drop calculation for a duct of square cross-section is given by (where, x = each side of the square duct). (A) x (B) √(πx) (C) √(2x) (D) √(x/2)

Last Answer : (A) x

The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Description : The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Last Answer : (C) 1/A

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

Vena-contracta formed during flow of a liquid through an orificemeter has (A) Minimum liquid cross-section (B) More diameter compared to orifice diameter (C) Minimum velocity of fluid stream (D) None of these

Description : Vena-contracta formed during flow of a liquid through an orificemeter has (A) Minimum liquid cross-section (B) More diameter compared to orifice diameter (C) Minimum velocity of fluid stream (D) None of these

Last Answer : (A) Minimum liquid cross-section

The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Description : The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Last Answer : (A) Parabolic

For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Description : For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Last Answer : (D) d

Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the first fluid, the pressure drop will (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Description : Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the ... (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Last Answer : (B) Decrease

In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Description : In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Last Answer : (A) Gives a higher shell side pressure drop

Discharge in laminar flow through a pipe varies (A) As the square of the radius (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the diameter

Description : Discharge in laminar flow through a pipe varies (A) As the square of the radius (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the diameter

Last Answer : (A) As the square of the radius

For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Description : For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Last Answer : (A) √x

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

If the side of a square sewer is 1000 mm, the diameter of a hydraulically equivalent circular section, is A. 1045 mm B. 1065 mm C. 1075 mm D. 1095 mm

Description : If the side of a square sewer is 1000 mm, the diameter of a hydraulically equivalent circular section, is A. 1045 mm B. 1065 mm C. 1075 mm D. 1095 mm

Last Answer : ANS: D

The ratio of the diameter of a circular section and the side of a square section hydraulically equivalent, is A. 1.095 B. 1.085 C. 1.075 D. 1.065

Description : The ratio of the diameter of a circular section and the side of a square section hydraulically equivalent, is A. 1.095 B. 1.085 C. 1.075 D. 1.065

Last Answer : ANS: A

The maximum discharge through a circular channel takes place, when the depth of the fluid flow is __________ times the pipe diameter. (A) 0.25 (B) 0.5 (C) 0.66 (D) 0.95

Description : The maximum discharge through a circular channel takes place, when the depth of the fluid flow is __________ times the pipe diameter. (A) 0.25 (B) 0.5 (C) 0.66 (D) 0.95

Last Answer : (D) 0.95

Find the remainder when f(x)=4x(cube) - 12x(square) +14x - 3 is divided by g(x) = (2x-1). -Maths 9th

Description : Find the remainder when f(x)=4x(cube) - 12x(square) +14x - 3 is divided by g(x) = (2x-1). -Maths 9th

Last Answer : ____2x2-5x+4________________ 2x-1 ) 4x3-12x2+14x-3( 4x3-2x2 - + ____________ 0 -10x2+14x-3 ... + ___________ X+1

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Show that 2x+1 is a factor of polynomial 2x(cube) - 11x(square) - 4x + 1. -Maths 9th

Description : Show that 2x+1 is a factor of polynomial 2x(cube) - 11x(square) - 4x + 1. -Maths 9th

Last Answer : Solution :-

Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Description : Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Last Answer : (A) Fluid flow rate & friction loss

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

In area meter (e.g., Rotameter), with increase in the fluid flow rate, the (A) Pressure drop increases linearly (B) Pressure drop is almost constant (C) Area through which fluid flows does not vary (D) None of these

Description : In area meter (e.g., Rotameter), with increase in the fluid flow rate, the (A) Pressure drop increases linearly (B) Pressure drop is almost constant (C) Area through which fluid flows does not vary (D) None of these

Last Answer : (B) Pressure drop is almost constant

For turbulent flow of an incompressible fluid through a pipe, the flow rate ‘Q’ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent 'n' is (A) 1 (B) 0 (C) < 1 (D) > 1

Description : For turbulent flow of an incompressible fluid through a pipe, the flow rate ‘Q’ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent 'n' is (A) 1 (B) 0 (C) < 1 (D) > 1

Last Answer : (C) < 1

In laminar flow through a round tube, the discharge varies (A) Linearly as the viscosity (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the radius

Description : In laminar flow through a round tube, the discharge varies (A) Linearly as the viscosity (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the radius

Last Answer : (C) Inversely as the viscosity

The equivalent diameter for pressure drop is __________ that for heat transfer. (A) Smaller than (B) Greater than (C) Equal to (D) Not related with

Description : The equivalent diameter for pressure drop is __________ that for heat transfer. (A) Smaller than (B) Greater than (C) Equal to (D) Not related with

Last Answer : (A) Smaller than

For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Last Answer : (B) 1

A short masonry pillar is 60 cm x 60 cm in cross-section, the core of the pillar is a square whose side is (A) 17.32 cm (B) 14.14 cm (C) 20.00 cm (D) 22.36 cm

Description : A short masonry pillar is 60 cm x 60 cm in cross-section, the core of the pillar is a square whose side is (A) 17.32 cm (B) 14.14 cm (C) 20.00 cm (D) 22.36 cm

Last Answer : (B) 14.14 cm

Best side slope for most economical trapezoidal section in open channel flow, wherein side slopes are defined by : X horizontal to 1 vertical, is when X equals : (a) 0.404 (b) 0.500 (c) 0.577 (d) 0.673

Description : Best side slope for most economical trapezoidal section in open channel flow, wherein side slopes are defined by : X horizontal to 1 vertical, is when X equals : (a) 0.404 (b) 0.500 (c) 0.577 (d) 0.673

Last Answer : (c) 0.577

If 'x' is the depth of flow in an open channel of large width, then the hydraulic radius is equal to (A) x (B) x/2 (C) x/3 (D) 2x/3

Description : If 'x' is the depth of flow in an open channel of large width, then the hydraulic radius is equal to (A) x (B) x/2 (C) x/3 (D) 2x/3

Last Answer : (A) x

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

20. The velocity of flow is same at all points in the cross-section of a channel. A) True B) False

Description : 20. The velocity of flow is same at all points in the cross-section of a channel. A) True B) False

Last Answer : B

Boundary layer separation occurs when the (A) Pressure reaches a minimum (B) Cross-section of the channel is reduced (C) Valve is closed in a pipeline (D) Velocity of sound is reached

Description : Boundary layer separation occurs when the (A) Pressure reaches a minimum (B) Cross-section of the channel is reduced (C) Valve is closed in a pipeline (D) Velocity of sound is reached

Last Answer : (B) Cross-section of the channel is reduced

Mass velocity is independent of temperature & pressure, when the flow is (A) Unsteady through unchanged cross-section (B) Steady through changing cross-section (C) Steady and the cross-section is unchanged (D) Unsteady and the cross-section is changed

Description : Mass velocity is independent of temperature & pressure, when the flow is (A) Unsteady through unchanged cross-section (B) Steady through changing cross-section (C) Steady and the cross-section is unchanged (D) Unsteady and the cross-section is changed

Last Answer : (C) Steady and the cross-section is unchanged

In which of the following cases, it is possible for flow to occur from low pressure to high pressure? (A) Flow of liquid upward in a vertical pipe (B) Flow through a converging section (C) Flow of air downward in a pipe (D) Impossible in a constant cross-section conduit

Description : In which of the following cases, it is possible for flow to occur from low pressure to high pressure? (A) Flow of liquid upward in a vertical pipe (B) Flow through a converging section (C) Flow of air downward in a pipe (D) Impossible in a constant cross-section conduit

Last Answer : (B) Flow through a converging section

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

For the same flow rate of a fluid, the pressure drop is the least for (A) Venturimeter (B) Orificemeter (C) Flow-nozzle (D) Δp is same for all

Description : For the same flow rate of a fluid, the pressure drop is the least for (A) Venturimeter (B) Orificemeter (C) Flow-nozzle (D) Δp is same for all

Last Answer : (A) Venturimeter

Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Description : Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Last Answer : (A) Increase

The Bernoulli's equation is based on the assumption that (A) There is no loss of energy of the liquid flowing (B) The velocity of flow is uniform across any cross-section of the pipe (C) No force except gravity acts on the fluid (D) All of the above

Description : The Bernoulli's equation is based on the assumption that (A) There is no loss of energy of the liquid flowing (B) The velocity of flow is uniform across any cross-section of the pipe (C) No force except gravity acts on the fluid (D) All of the above

Last Answer : Answer: Option D

The ratio of the section modulus of a square section of side B and that of a circular section of diameter D, is (A) 2 /15 (B) 3 /16 (C) 3 /8 (D) /16

Description : The ratio of the section modulus of a square section of side B and that of a circular section of  diameter D, is  (A) 2 /15  (B) 3 /16  (C) 3 /8  (D) /16

Last Answer : (B) 3 /16 

In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Description : In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Last Answer : (B) Square root

For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, when the __________ is the controlling resistance. (A) Film diffusion (B) Diffusion through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Description : For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, ... through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Last Answer : (B) Diffusion through ash layer

essure drop (Δp) for a fluid flowing in turbulent flow through a pipe is a function of velocity (V) as (A) V1.8 (B) V-0.2 (C) V2.7 (D) V

Description : essure drop (Δp) for a fluid flowing in turbulent flow through a pipe is a function of velocity (V) as (A) V1.8 (B) V-0.2 (C) V2.7 (D) V

Last Answer : (D) V

Fluid flow in a/an __________ is an example of pressure flow. (A) Partially filled pipeline (B) Pipe (C) Open channel (D) River

Description : Fluid flow in a/an __________ is an example of pressure flow. (A) Partially filled pipeline (B) Pipe (C) Open channel (D) River

Last Answer : (B) Pipe

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as the (A) Square root of the velocity (B) Square of the viscosity (C) Filtration time only (D) Washing time only

Description : In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as the (A) Square root of the velocity (B) Square of the viscosity (C) Filtration time only (D) Washing time only

Last Answer : (A) Square root of the velocity