For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

For flow past a flat plate, if ‘x’ is the distance along the plate in the
direction of flow, the boundary layer thickness is proportional to
(A) √x
(B) 1/√x
(C) x
(D) 1/x
Answe
by

1 Answer

Answer :

(A) √x
by

Related questions

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Description : For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Last Answer : (B) NPr 1/3

The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number(A) Increases(B) Decreases(C) Remain same(D) May increase or decrease.

Description : The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number. (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease

Last Answer : (B) Decreases

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Description : In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Last Answer : (B) Increase gradually

What is the ratio of displacement thickness to nominal thickness for a linear distribution of velocity in the boundary layer on a flat plate? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Description : What is the ratio of displacement thickness to nominal thickness for a linear distribution of velocity in the boundary layer on a flat plate? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Last Answer : (A) 0.5

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Resistance to heat flow by conduction is proportional to (where, t & ρ are thickness & density of the material respectively and A = area normal tothe direction of heat flow.) (A) t (B) 1/ρ (C) 1/A (D) All (A), (B) & (C)

Description : Resistance to heat flow by conduction is proportional to (where, t & ρ are thickness & density of the material respectively and A = area normal tothe direction of heat flow.) (A) t (B) 1/ρ (C) 1/A (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The equivalent diameter for fluid flow through square cross section channel of side 'x', for pressure drop calculation purpose is given by (A) 4x (B) 2x (C) x (D) √x

Description : The equivalent diameter for fluid flow through square cross section channel of side 'x', for pressure drop calculation purpose is given by (A) 4x (B) 2x (C) x (D) √x

Last Answer : (C) x

Boundary layer exists in flow (A) Of real fluids (B) Over flat surfaces only (C) In pipes only (D) Of ideal fluids only

Description : Boundary layer exists in flow (A) Of real fluids (B) Over flat surfaces only (C) In pipes only (D) Of ideal fluids only

Last Answer : (A) Of real fluids

At the point of boundary layer separation in fluid flow, the (A) Shear stress is maximum (B) Velocity gradient is flat (C) Density variation is maximum (D) Shear stress is zero

Description : At the point of boundary layer separation in fluid flow, the (A) Shear stress is maximum (B) Velocity gradient is flat (C) Density variation is maximum (D) Shear stress is zero

Last Answer : Option A

02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) AgreeB) Disagree

Description : 02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) Agree B) Disagree

Last Answer : A

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Description : Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Last Answer : (B) < 1

. If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary layer (C) Thermal & concentration boundary layers are of equal thickness (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Description : . If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary ... (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

Last Answer : (A) Thermal boundary layer lies inside the concentration boundary layer

The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Description : The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Last Answer : (A) < 1

Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Last Answer : (D) Reduction of pressure gradient to zero

Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Last Answer : (C) Adverse pressure gradient

During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to (A) Time (B) Square root of time (C) Square of time (D) Cube of time

Description : During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to (A) Time (B) Square root of time (C) Square of time (D) Cube of time

Last Answer : Option B

How the thickness of thermal boundary layer and thickness of hydrodynamic boundary layer related ?

Description : How the thickness of thermal boundary layer and thickness of hydrodynamic boundary layer related ?

Last Answer : Ratio of their thickness = (Prandtl number)-1/3.

A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature at the two sides of the wall are 400 and 1200°K, then the temperature drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Last Answer : (D) 160

What is a Plate boundary where plates slide past one another?

Description : What is a Plate boundary where plates slide past one another?

Last Answer : a transform boundary

Time factor for a clay layer is (A) A dimensional parameter (B) Directly proportional to permeability of soil (C) Inversely proportional to drainage path (D) Independent of thickness of clay layer

Description : Time factor for a clay layer is (A) A dimensional parameter (B) Directly proportional to permeability of soil (C) Inversely proportional to drainage path (D) Independent of thickness of clay layer

Last Answer : (B) Directly proportional to permeability of soil

A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Description : A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Last Answer : (B) 20 KPa

The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Description : The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Last Answer : d/85

Find the radius of curvature of √x+√y=√a

Description : Find the radius of curvature of √x+√y=√a

Last Answer : √x+√y=√a at (a÷4 , a÷4). Find the radius of curvature.

Why Blue jays and robins do not interbreed. Assuming that blue jays and robins share the same habitat describe the possible conditions that keep these birds reproductively isolated. Explain your answe?

Description : Why Blue jays and robins do not interbreed. Assuming that blue jays and robins share the same habitat describe the possible conditions that keep these birds reproductively isolated. Explain your answe?

Last Answer : Need answer

Compute the Gauss law for D = 10ρ 3 /4 i, in cylindrical coordinates with ρ = 4m, z = 0 and z = 5, hence find charge using volume integral. a) 6100 π b) 6200 π c) 6300 π d) 6400 π View Answe

Description : Compute the Gauss law for D = 10ρ 3 /4 i, in cylindrical coordinates with ρ = 4m, z = 0 and z = 5, hence find charge using volume integral. a) 6100 π b) 6200 π c) 6300 π d) 6400 π View Answe

Last Answer : d) 6400 π

Bernoulli's equation describes the (A) Mechanical energy balance in potential flow (B) Kinetic energy balance in laminar flow (C) Mechanical energy balance in turbulent flow (D) Mechanical energy balance in boundary layer

Description : Bernoulli's equation describes the (A) Mechanical energy balance in potential flow (B) Kinetic energy balance in laminar flow (C) Mechanical energy balance in turbulent flow (D) Mechanical energy balance in boundary layer

Last Answer : (A) Mechanical energy balance in potential flow

Boundary layer separation is characterised by one of the conditions given below, where 'Re' is the Reynolds number for the flow. Select the appropriate conditions. (A) Re << 1, accelerating flow (B) Re >> 1, accelerating flow (C) Re << 1, decelerating flow (D) Re >>1, decelerating flow

Description : Boundary layer separation is characterised by one of the conditions given below, where 'Re' is the Reynolds number for the flow. Select the appropriate conditions. (A) Re > 1, accelerating flow (C) Re >1, decelerating flow

Last Answer : (D) Re >>1, decelerating flow

In fluid flow, the boundary layer separation cannot occur (A) In case of boundaries experiencing form drag (B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of these

Description : In fluid flow, the boundary layer separation cannot occur (A) In case of boundaries experiencing form drag (B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of theseIn ... B) At points of abrupt changes in the flow directions (C) In laminar flow (D) None of these

Last Answer : (D) None of these

The length of the tube necessary for the boundary layer to reach thecentre of the tube and for fully developed flow to be established is called the__________ length.(A) Equivalent(B) Transition(C) Prandtl mixing(D) None of these

Description : The length of the tube necessary for the boundary layer to reach thecentre of the tube and for fully developed flow to be established is called the __________ length. (A) Equivalent (B) Transition (C) Prandtl mixing (D) None of these

Last Answer : (B) Transition

The effect of solid boundary on the fluid flow is confined to the boundary layer, except for fluids (A) Having high viscosities (B) Moving at low velocities (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The effect of solid boundary on the fluid flow is confined to the boundary layer, except for fluids (A) Having high viscosities (B) Moving at low velocities (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Which of the following must be followed by the flow of a fluid (real or ideal)? (I) Newton's law of viscosity. (II) Newton's second law of motion. (III) The continuity equation. (IV) Velocity of boundary layer must be zero relative to boundary. (V) Fluid cannot penetrate a boundary. (A) I, II, III (B) II, III, V (C) I, II, V (D) II, IV, V

Description : Which of the following must be followed by the flow of a fluid (real or ideal)? (I) Newton's law of viscosity. (II) Newton's second law of motion. (III) The continuity equation. (IV) Velocity of boundary layer must be zero relative to ... . (A) I, II, III (B) II, III, V (C) I, II, V (D) II, IV, V

Last Answer : (B) II, III, V

__________ flow means the flow of incompressible fluid with no shear. (A) Potential (B) Streamline (C) Creep (D) Boundary layer

Description : __________ flow means the flow of incompressible fluid with no shear. (A) Potential (B) Streamline (C) Creep (D) Boundary layer

Last Answer : (A) Potential

Existence of boundary layer in fluid flow is because of the (A) Surface tension (B) Fluid density (C) Fluid viscosity (D) Gravity forces

Description : Existence of boundary layer in fluid flow is because of the (A) Surface tension (B) Fluid density (C) Fluid viscosity (D) Gravity forces

Last Answer : (C) Fluid viscosity

The boundary layer is that part of a moving fluid, in which the fluid velocity is (A) Affected by the fluid flow pressure (B) Constant(C) Affected by the presence of a solid boundary(D) All (A), (B) and (C)

Description : The boundary layer is that part of a moving fluid, in which the fluid velocity is (A) Affected by the fluid flow pressure (B) Constant (C) Affected by the presence of a solid boundary (D) All (A), (B) and (C)

Last Answer : (C) Affected by the presence of a solid boundary

The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Description : The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Last Answer : (B) Cavitation

Pick out the wrong statement about a streamline. (A) It is always parallel to the main direction of the fluid flow (B) It is a line across which there is no flow and it is equivalent to a rigid boundary(C) Streamlines intersect at isolated point of zero velocity and infinitevelocity(D) The fluid lying between any two streamlines can be considered to be inisolation and the streamline spacing varies inversely as the velocity

Description : Pick out the wrong statement about a streamline. (A) It is always parallel to the main direction of the fluid flow (B) It is a line across which there is no flow and it is ... any two streamlines can be considered to be in isolation and the streamline spacing varies inversely as the velocity

Last Answer : (A) It is always parallel to the main direction of the fluid flow

In case of Couette flow, the fluid flow is between two large flat parallel plates with (A) Top plate moving and the bottom plate fixed (B) Bottom plate moving and the top plate fixed (C) Both the plates fixed (D) Both the plates moving

Description : In case of Couette flow, the fluid flow is between two large flat parallel plates with (A) Top plate moving and the bottom plate fixed (B) Bottom plate moving and the top plate fixed (C) Both the plates fixed (D) Both the plates moving

Last Answer : (A) Top plate moving and the bottom plate fixed

Nusselt number is related to Grashoff number (Gr) in turbulent & laminar flow respectively, in respect of free convection over a vertical flat plate as (A) Gr0.25, Gr (B) Gr0.25, Gr0.33 (C) Gr, Gr0.25 (D) Gr0.33, Gr0.25

Description : Nusselt number is related to Grashoff number (Gr) in turbulent & laminar flow respectively, in respect of free convection over a vertical flat plate as (A) Gr0.25, Gr (B) Gr0.25, Gr0.33 (C) Gr, Gr0.25 (D) Gr0.33, Gr0.25

Last Answer : Option A

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

The thickness of condensate layer in filmwise condensation depends on the (A) Condensation rate (B) Surface configuration (C) Liquid flow rate from the surface (D) All (A), (B) and (C)

Description : The thickness of condensate layer in filmwise condensation depends on the (A) Condensation rate (B) Surface configuration (C) Liquid flow rate from the surface (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

An ideal flow of any fluid must satisfy (A) Pascal law (B) Newton's law of viscosity (C) Boundary layer theory (D) Continuity equation

Description : An ideal flow of any fluid must satisfy (A) Pascal law (B) Newton's law of viscosity (C) Boundary layer theory (D) Continuity equation

Last Answer : Answer: Option D

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Description : When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Last Answer : (b) Directly proportional to

According to Bernoulli's equation for steady ideal fluid flow (A) Principle of conservation of mass holds (B) Velocity and pressure are inversely proportional (C) Total energy is constant throughout (D) The energy is constant along a streamline but may vary across streamlines

Description : According to Bernoulli's equation for steady ideal fluid flow (A) Principle of conservation of mass holds (B) Velocity and pressure are inversely proportional (C) Total energy is constant throughout (D) The energy is constant along a streamline but may vary across streamlines

Last Answer : Answer: Option D

The drying time between fixed moisture contents within the 'constant rate period' is proportional to (assuming that drying occurs from all surfaces of the solid) (where, T = thickness of the solid). (A) √T (B) T (C) T 1.5 (D) T

Description : The drying time between fixed moisture contents within the 'constant rate period' is proportional to (assuming that drying occurs from all surfaces of the solid) (where, T = thickness of the solid). (A) √T (B) T (C) T 1.5 (D) T

Last Answer : (B) T