Turndown ratio of a gas burner is equal to the (A) Maximum to minimum heat input ratio (B) Maximum to minimum permissible gas flow rate (C) Both (A) & (B) (D) Minimum to maximum heat input ratio

Turndown ratio of a gas burner is equal to the
(A) Maximum to minimum heat input ratio
(B) Maximum to minimum permissible gas flow rate
(C) Both (A) & (B)
(D) Minimum to maximum heat input ratio
by

1 Answer

Answer :

(C) Both (A) & (B)
by

Related questions

Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Description : Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Last Answer : (A) Range of fuel firing rates

Turn down ratio of a burner (A) Should be as low as possible i.e., 1 : 2 (B) Should be 1:1 for a batch type furnace (C) Is the ratio of maximum to minimum permissible heat input rates (D) Is normally much more for a continuous furnace as compared to a batch furnace

Description : Turn down ratio of a burner (A) Should be as low as possible i.e., 1 : 2 (B) Should be 1:1 for a batch type furnace (C) Is the ratio of maximum to minimum permissible heat input rates (D) Is normally much more for a continuous furnace as compared to a batch furnace

Last Answer : (C) Is the ratio of maximum to minimum permissible heat input rates

Pick up the correct statement from the following: A. Maximum daily flow = 2 times the average daily flow B. Maximum daily flow = average daily flow C. Sewers are designed for minimum permissible velocity at minimum flow D. All the above

Description : Pick up the correct statement from the following: A. Maximum daily flow = 2 times the average daily flow B. Maximum daily flow = average daily flow C. Sewers are designed for minimum permissible velocity at minimum flow D. All the above

Last Answer : ANS: D

The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Description : The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Last Answer : (A) 1.118

In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Description : In McCabe-Thiele method of theoretical plate calculation for a distillation column, the operating lines of stripping and rectifying sections coincide with the diagonal at __________ reflux. (A) Total (B) Minimum (C) Operating (D) Maximum permissible

Last Answer : (A) Total

At __________ reflux, theoretical number of plates in a distillation coloumn is calculated using Fenske-Underwood equation. (A) Operating (B) Total (C) Minimum (D) Maximum permissible

Description : At __________ reflux, theoretical number of plates in a distillation coloumn is calculated using Fenske-Underwood equation. (A) Operating (B) Total (C) Minimum (D) Maximum permissible

Last Answer : (B) Total

Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a given discharge. 4. The Froude number is equal to unity. Which of these statements are correct? (a) 1 , 2 & 3 only (b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Description : Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a ... b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Last Answer : (b) 1, 2, 3 & 4

The amount of combustible escaping unconsumed from the furnace, depends upon the (A) Air supplied and furnace temperature (B) Burner design (thoroughness of mixing versus stratification) (C) Air preheat and the flow of gases in the furnace (mixing by induction, by acceleration or by change of direction) (D) All (A), (B) and (C)

Description : The amount of combustible escaping unconsumed from the furnace, depends upon the (A) Air supplied and furnace temperature (B) Burner design (thoroughness of mixing versus stratification) (C) Air preheat and the flow of ... , by acceleration or by change of direction) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner? (A) Output & fineness (B) Velocity (C) Both (A) & (B) (D) None of these

Description : Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner? (A) Output & fineness (B) Velocity (C) Both (A) & (B) (D) None of these

Last Answer : Option C

In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Description : In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Last Answer : (C) Zero

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What is the maximum data transfer rate for this microprocessor? (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec

Description : Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What ... (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec 

Last Answer : (B) 4x106 bytes/sec

Atomising steam to fuel oil ratio in a burner should be around (A) 0.5 (B) 1.5 (C) 2.5 (D) 3.5

Description : Atomising steam to fuel oil ratio in a burner should be around (A) 0.5 (B) 1.5 (C) 2.5 (D) 3.5

Last Answer : (A) 0.5

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum along the length of the reactor (C) Goes through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Description : An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum ... through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Last Answer : (A) Is maximum at the inlet of the reactor

When a multistage tray tower uses a minimum reflux ratio, it implies (A) Infinite trays and maximum reboiler heat load (B) Infinite trays and minimum reboiler heat load (C) Minimum trays and minimum reboiler heat load (D) Minimum trays and maximum reboiler heat load

Description : When a multistage tray tower uses a minimum reflux ratio, it implies (A) Infinite trays and maximum reboiler heat load (B) Infinite trays and minimum reboiler heat load (C) Minimum trays and minimum reboiler heat load (D) Minimum trays and maximum reboiler heat load

Last Answer : (A) Infinite trays and maximum reboiler heat load

Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Description : Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Last Answer : (B) 25

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

A gas is termed as non-toxic, if its maximum permissible concentration (TLV) ranges from __________ ppm. (A) 1000 to 2000 (B) 3000 to 6000 (C) 6000 to 9000 (D) 10000 to 100000

Description : A gas is termed as non-toxic, if its maximum permissible concentration (TLV) ranges from __________ ppm. (A) 1000 to 2000 (B) 3000 to 6000 (C) 6000 to 9000 (D) 10000 to 100000

Last Answer : (D) 10000 to 100000

Threshold limit value (TLV) i.e., the maximum permissible safe limit of phosgene gas which Hitler used to use to kill his enemies in 'gas chamber' is about __________ ppm. (A) < 1 (B) 10-100 (C) 100-200 (D) 100-1000

Description : Threshold limit value (TLV) i.e., the maximum permissible safe limit of phosgene gas which Hitler used to use to kill his enemies in 'gas chamber' is about __________ ppm. (A) < 1 (B) 10-100 (C) 100-200 (D) 100-1000

Last Answer : (A) < 1

Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Description : Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Last Answer : Answer: D

Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Description : Overall thermal resistance for conductive heat transfer through a series of flat resistances is equal to the (A) Maximum resistance in the series (B) Sum of all resistances (C) Average of all resistances (D) Minimum resistance presents in the series

Last Answer : (B) Sum of all resistances

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

Absorption (liquid-gas system) with evolution of heat as compared to isothermal absorption results in (A) Decreased solute solubility (B) Large minimum liquid to gas (L/G) ratio (C) Large number of trays(D) All (A), (B) and (C)

Description : Absorption (liquid-gas system) with evolution of heat as compared to isothermal absorption results in (A) Decreased solute solubility (B) Large minimum liquid to gas (L/G) ratio (C) Large number of trays (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Main gas valve in a gaseous fuel burner is a __________ valve. (A) Gate (B) Butterfly (C) Globe (D) None of these

Description : Main gas valve in a gaseous fuel burner is a __________ valve. (A) Gate (B) Butterfly (C) Globe (D) None of these

Last Answer : (A) Gate

A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Description : A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Last Answer : (B) 2 0.8

Signal normally used to study non-ideal flow by stimulus response technique is __________ input. (A) Pulse (B) Step (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Signal normally used to study non-ideal flow by stimulus response technique is __________ input. (A) Pulse (B) Step (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Maximum heat transfer rate is achieved in __________ flow. (A) Co-current (B) Counter-current (C) Turbulent (D) Laminar

Description : Maximum heat transfer rate is achieved in __________ flow. (A) Co-current (B) Counter-current (C) Turbulent (D) Laminar

Last Answer : (C) Turbulen

Pick out the correct statement. (A) Higher is the temperature of the radiating body, higher is the wavelength of radiation (B) Logarithmic mean area is used for calculating the heat flow rate through a thick walled cylinder (C) The wavelength corresponding to maximum mono-chromatic emissive power increases with rise in temperature (D) Solid angle subtended by the finite surface at the radiating element is called the angle of incidence

Description : Pick out the correct statement. (A) Higher is the temperature of the radiating body, higher is the wavelength of radiation (B) Logarithmic mean area is used for calculating the heat flow rate ... ) Solid angle subtended by the finite surface at the radiating element is called the angle of incidence

Last Answer : (B) Logarithmic mean area is used for calculating the heat flow rate through a thick walled cylinder

Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Description : Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Last Answer : (B) Turbulent

An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Description : An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Last Answer : (A) Maximum at the inlet of the reactor

If a burner on the stove heats the bottom of a pot what transfer of heat is ti?

Description : If a burner on the stove heats the bottom of a pot what transfer of heat is ti?

Last Answer : conduction

If a burner on the stove heats the bottom of a pot what transfer of heat is ti?

Description : If a burner on the stove heats the bottom of a pot what transfer of heat is ti?

Last Answer : conduction

To ensure that the heat from a burner is spread evenly across the bottom of a beaker, one should use a _______.?

Description : To ensure that the heat from a burner is spread evenly across the bottom of a beaker, one should use a _______.?

Last Answer : i don’t know

Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Description : Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Last Answer : • All of the above

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

Out of the following, maximum temperature drop for a given heat flow & for the same thickness will be in the case of (A) Steel (B) Glass wood (C) Copper (D) Fireclay bricks

Description : Out of the following, maximum temperature drop for a given heat flow & for the same thickness will be in the case of (A) Steel (B) Glass wood (C) Copper (D) Fireclay bricks

Last Answer : B) Glass wood

Does HD video camera + Regular DVD burner + HDTV [equal] Bad picture?

Description : Does HD video camera + Regular DVD burner + HDTV [equal] Bad picture?

Last Answer : answer:Yes, the Video DVD format will down-res your HD signal to standard definition (roughly 640×480). If you want HD video, look into a Blu-Ray burner or the AppleTV (networkable hard-drive-based media center with built-in software for navigation and remote control). And welcome to Ask-public.

LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface area required is the least in the __________ flow. (A) Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Description : LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface ... Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Last Answer : (D) Same in either 'a', b' or 'c'

Which of the following quantities need not be fixed before starting the design of a co-current absorber? (A) Heat gain or loss (B) Flow rate of entering liquid (C) Flow rate of gas (D) None of these

Description : Which of the following quantities need not be fixed before starting the design of a co-current absorber? (A) Heat gain or loss (B) Flow rate of entering liquid (C) Flow rate of gas (D) None of these

Last Answer : (B) Flow rate of entering liquid

Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point (C) Each ton of petroleum oil on distillation produces about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil

Description : Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches ... about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil

Last Answer : (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point

Extended heat transfer surface like fins are used to increase the heat transfer rate. Fin efficiency is defined as the ratio of heat transferred across the fin surface to the theoretical heat transfer across an equal area held at the (A) Surrounding temperature (B) Average temperature of the fin (C) Temperature of the fin end (D) Constant temperature equal to that of the base

Description : Extended heat transfer surface like fins are used to increase the heat transfer rate. Fin efficiency is defined as the ratio of heat transferred across the fin surface to the theoretical heat transfer ... (C) Temperature of the fin end (D) Constant temperature equal to that of the base

Last Answer : (D) Constant temperature equal to that of the base

For same compression ratio and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Description : For same compression ratio and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Last Answer : ANSWER a. Otto cycle is more efficient

Give reasons for the following observations: (a) The element carbon forms a very large number of compounds. (b) Air holes of a gas burner have to be adjusted when the heated vessels get blackened by the flame. (c) Use of synthetic detergents causes pollution of water. -Chemistry

Description : Give reasons for the following observations: (a) The element carbon forms a very large number of compounds. (b) Air holes of a gas burner have to be adjusted when the heated vessels get blackened by the flame. (c) Use of synthetic detergents causes pollution of water. -Chemistry

Last Answer : Answer. (a) Carbon forms large number of compounds since carbon is small in size and can form stable covalent bonds (catenation) and it shows tetravalency. (b) Air holes of gas burner are ... not get blackened. (c) Some synthetic detergents are non-biodegradable, therefore, cause pollution of water.

What kind of combustion is observed in alkanes? Why do air holes of a gas burner have to be adjusted when vessel being heated gets blackened by the flame? -Science

Description : What kind of combustion is observed in alkanes? Why do air holes of a gas burner have to be adjusted when vessel being heated gets blackened by the flame? -Science

Last Answer : Alkanes are saturated hydrocarbons and generally burn in air with a blue, non-sooty flame. If the bottoms of the cooking vessels in our homes are getting blackened, it shows that the air holes of the gas stove are getting blocked and the fuel is not burning completely.

What gas is used in a gas burner.?

Description : What gas is used in a gas burner.?

Last Answer : I think you are asking about the cooking gas in India. Here we use LPG that is Liquid Petroleum Gas. It is made up of hydrocarbons which is compressed to liquid state.

What does Perma-Flame Instant Re-Ignition mean on the Dacor SGM304S 30" Preference All-Gas 4 Burner Cooktop ?

Description : What does Perma-Flame Instant Re-Ignition mean on the Dacor SGM304S 30" Preference All-Gas 4 Burner Cooktop ?

Last Answer : If the piolet light blows out it will reignite instantly so you do not need matches.

When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is complete d) Minimum preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Description : When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is ... preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Last Answer : b) Immediately prior to commencing the first pass and subsequent passes

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.