Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Turndown ratio of a burner gives an idea of the __________ in the
furnace.
(A) Range of fuel firing rates
(B) Volume of the combustion chamber
(C) Maximum heat input rate only
(D) Minimum heat input rate only
by

1 Answer

Answer :

(A) Range of fuel firing rates
by

Related questions

Turndown ratio of a gas burner is equal to the (A) Maximum to minimum heat input ratio (B) Maximum to minimum permissible gas flow rate (C) Both (A) & (B) (D) Minimum to maximum heat input ratio

Description : Turndown ratio of a gas burner is equal to the (A) Maximum to minimum heat input ratio (B) Maximum to minimum permissible gas flow rate (C) Both (A) & (B) (D) Minimum to maximum heat input ratio

Last Answer : (C) Both (A) & (B)

Turn down ratio of a burner (A) Should be as low as possible i.e., 1 : 2 (B) Should be 1:1 for a batch type furnace (C) Is the ratio of maximum to minimum permissible heat input rates (D) Is normally much more for a continuous furnace as compared to a batch furnace

Description : Turn down ratio of a burner (A) Should be as low as possible i.e., 1 : 2 (B) Should be 1:1 for a batch type furnace (C) Is the ratio of maximum to minimum permissible heat input rates (D) Is normally much more for a continuous furnace as compared to a batch furnace

Last Answer : (C) Is the ratio of maximum to minimum permissible heat input rates

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal(C) Accelerates the burning rate and economises on fuel combustion(D) All (A), (B) and (C)

Description : The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel combustion (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel combustion

What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Description : What is defined as the ratio of the net electrical power output to the rate of fuel energy input?  A. Combustion efficiency  B. Thermal efficiency  C. Overall efficiency  D. Furnace efficiency

Last Answer : Overall efficiency

Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Description : Basic Parts of a Boiler. Burner, • the combustion chamber, • the heat exchanger • All of the above

Last Answer : • All of the above

Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Description : Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Last Answer : (A) Requires larger combustion chamber than rich gaseous fuel

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

Amount of coal lost in ash particle, which is carried through the boiler system, depends upon the (A) Physical nature, ash content and fineness of the coal (B) Amount of excess air supplied and load on the boiler (C) Type of burner and combustion chamber (D) All (A), (B) and (C)

Description : Amount of coal lost in ash particle, which is carried through the boiler system, depends upon the (A) Physical nature, ash content and fineness of the coal (B) Amount of excess air supplied and load on the boiler (C) Type of burner and combustion chamber (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Description : In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Last Answer : (C) Radiation of heat from the roof of the combustion chamber

Which of the following will generate maximum volume of product of complete combustion (Nm3 /Nm3 of fuel)? (A) Carburetted water gas (B) Blast furnace gas(C) Natural gas(D) Producers' gas

Description : Which of the following will generate maximum volume of product of complete combustion (Nm3 /Nm3 of fuel)? (A) Carburetted water gas (B) Blast furnace gas (C) Natural gas (D) Producers' gas

Last Answer : (C) Natural gas

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Description : The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel consumption

Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Description : Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Last Answer : Answer: D

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Description : Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Last Answer : (B) Reducing sulphur content in the fuel

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these

Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Description : Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Last Answer : (B) Natural gas

Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Description : Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Last Answer : (A) CO content

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Description : Presence of moisture in fuel oil would (A) Keep the burner tips cool (B) Aid in proper combustion (C) Because sputtering, possibly extinguishing flame (D) Clean the nozzles

Last Answer : (D) Clean the nozzles

Absolute vapor pressure of petrofuels is found by Reid bomb which is heated in water bath to 100°F. In Reid apparatus, the ratio of the volume of air chamber to that of the liquid fuel chamber is (A) 4 (B) 3 (C) 2 (D) 1

Description : Absolute vapor pressure of petrofuels is found by Reid bomb which is heated in water bath to 100°F. In Reid apparatus, the ratio of the volume of air chamber to that of the liquid fuel chamber is (A) 4 (B) 3 (C) 2 (D) 1

Last Answer : (A) 4

Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Description : Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Last Answer : (B) 25

Function of secondary air in pulverised coal firing is to (A) Transport the coal to the burner (B) Dry the coal (C) Ensure efficient burning of coal around the burner (D) Reduce primary air requirement

Description : Function of secondary air in pulverised coal firing is to (A) Transport the coal to the burner (B) Dry the coal (C) Ensure efficient burning of coal around the burner (D) Reduce primary air requirement

Last Answer : (C) Ensure efficient burning of coal around the burner

Bunsen burner is an example of a/an __________ burner. (A) Inside mixing/premix type (B) Outside mixing/diffusion flame/nozzle mix type (C) Rotary cup (D) Submerged combustion

Description : Bunsen burner is an example of a/an __________ burner. (A) Inside mixing/premix type (B) Outside mixing/diffusion flame/nozzle mix type (C) Rotary cup (D) Submerged combustion

Last Answer : (A) Inside mixing/premix type

Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140

Description : Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140

Last Answer : (C) 90

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these

Description : Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these

Last Answer : (A) kcal/hr/m3 combustion space

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Last Answer : Ans :c

Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be (A) 9.5 : 1 (B) 12.5 : 1 (C) 15.5 : 1 (D) 18.5 : 1

Description : Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be (A) 9.5 : 1 (B) 12.5 : 1 (C) 15.5 : 1 (D) 18.5 : 1

Last Answer : (A) 9.5 : 1

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Description : The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Smoke is produced due to (A) Insufficient supply of combustion air and insufficient time for combustion (B) Poor quality of fuel and improper mixing of fuel & combustion air (C) Poor design & overloading of furnace (D) All (A), (B) and (C)

Description : Smoke is produced due to (A) Insufficient supply of combustion air and insufficient time for combustion (B) Poor quality of fuel and improper mixing of fuel & combustion air (C) Poor design & overloading of furnace (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Description : If the flame is produced under the hearth and then sweeps up into the heating chamber, this is called a/an __________ furnace. (A) Sidefired (B) Underfired (C) Covered (D) Recirculating

Last Answer : (B) Underfired

Atomising steam to fuel oil ratio in a burner should be around (A) 0.5 (B) 1.5 (C) 2.5 (D) 3.5

Description : Atomising steam to fuel oil ratio in a burner should be around (A) 0.5 (B) 1.5 (C) 2.5 (D) 3.5

Last Answer : (A) 0.5

Which of the following is not a part of a boiler a) burner the combination b) chamber c) water reservoir d) None above

Description : Which of the following is not a part of a boiler a) burner the combination b) chamber c) water reservoir d) None above

Last Answer : c) water reservoir