Description : The voltage at any point in an ac circuit will be a) Peak voltage b) RMS voltage c) Average voltage d) Source voltage
Last Answer : b) RMS voltage
Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values
Last Answer : D. peak values
Description : The rms value of the current in a wire which carries a d.c. current of 10 A and a sinusoidal alternating current of peak value 20 A is (A) 10 A (B) 14.14 A (C) 15 A (D) 17.32 A
Last Answer : The rms value of the current in a wire which carries a d.c. current of 10 A and a sinusoidal alternating current of peak value 20 A is 17.32 A
Description : Find the power of a wave given that the RMS value of E and H are 6 and 4.5 respectively. a) 24 b) 27 c) 29 d) 32
Last Answer : b) 27
Description : AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage
Last Answer : Answer: C
Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA
Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA
Description : What does the Voltmeter in AC mode show? Is it RMS value or peak value?
Last Answer : Multimeter in AC mode shows RMS value of the voltage or current. Also when it is DC mode it will show the RMS value only.
Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V
Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V
Description : Compute the power consumed by a material with current density 15 units in an area of 100 units. The potential measured across the material is 20V. a) 100kJ b) 250kJ c) 30kJ d) 15kJ
Last Answer : c) 30kJ
Description : Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value
Last Answer : Answer: B
Description : The minimum impedance of a 75 ohm transmission line with a SWR of 2.5 is a) 100 b) 50 c) 25 d) 30
Last Answer : d) 30
Description : The maximum impedance of a 50 ohm transmission line with SWR of 3 is a) 50/3 b) 3/50 c) 150 d) 450
Last Answer : c) 150
Description : The benefit of Maxwell equation is that a) Any parameter can be calculated b) Antenna can be designed c) Polarisation of the wave can be calculated d) Transmission line constants can be found
Last Answer : a) Any parameter can be calculated
Description : When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty
Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power
Last Answer : C. Mean power
Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power
Last Answer : A. Carrier power
Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power
Last Answer : C. Carrier power
Description : The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value
Description : The line integral of which parameter is zero for static fields? a) E b) H c) D d) B
Last Answer : a) E
Description : Which equation will hold good for a magnetic material? a) Line integral of H is zero b) Surface integral of H is zero c) Line integral of B is zero d) Surface integral of B is zero
Last Answer : d) Surface integral of B is zero
Description : Zero permeability/permittivity implies which state? a) No ions are allowed in the medium b) No current is generated in the medium c) No magnetic or electric energy is permitted in the medium d) No resistivity
Last Answer : c) No magnetic or electric energy is permitted in the medium
Description : Ampere law states that, a) Divergence of H is same as the flux b) Curl of D is same as the current c) Divergence of E is zero d) Curl of H is same as the current density
Last Answer : d) Curl of H is same as the current density
Description : When the rotational path of the magnetic field intensity is zero, then the current in the path will be a) 1 b) 0 c) ∞ d) 0.5
Last Answer : b) 0
Description : Find the current density on the conductor surface when a magnetic field H = 3cos x i + zcos x j A/m, for z>0 and zero, otherwise is applied to a perfectly conducting surface in xy plane. a) cos x i b) –cos x i c) cos x j d) –cos x j
Last Answer : b) –cos x i
Description : When the conduction current density and displacement current density are same, the dissipation factor will be a) Zero b) Minimum c) Maximum d) Unity
Last Answer : d) Unity
Description : If Laplace equation satisfies, then which of the following statements will be true? a) Potential will be zero b) Current will be infinite c) Resistance will be infinite d) Voltage will be same
Last Answer : b) Current will be infinite
Last Answer : Alternating current is measured by induction ammeter.
Description : The curl of a curl of a vector gives a a) Scalar b) Vector c) Zero value d) Non zero value
Last Answer : b) Vector
Description : When a vector is irrotational, which condition holds good? a) Stoke’s theorem gives non-zero value b) Stoke’s theorem gives zero value c) Divergence theorem is invalid d) Divergence theorem is valid
Last Answer : b) Stoke’s theorem gives zero value
Description : In the case of an unsymmetrical alternating current the average value must always be taken over?
Last Answer : In the case of an unsymmetrical alternating current the average value must always be taken over the whole cycle.
Description : Can I use eurometer calibrated in RMS to measure HWDC in peak?
Last Answer : No
Description : In AC circuits, AC meters measure – (1) mean values (2) rms values (3) peak values (4) mean square values
Last Answer : (2) rms values Explanation: Voltages and currents for AC circuits are generally expressed as rms (root mean square) values. For a sine wave, the relationship between the peak and the rms average is: rms value = 0.707 peak value.
Description : In AC circuits, AC meters measure (1) mean values (2) rms values (3) peak values (4) mean square values
Last Answer : rms values
Description : The skin depth is measured in a) Meter b) Millimetre c) Centimetre d) Micrometer
Last Answer : d) Micrometer
Description : Find the angle at which the potential due a dipole is measured, when the distance from one charge is 12cm and that due to other is 11cm, separated to each other by a distance of 2cm. a) 15 b) 30 c) 45 d) 60
Last Answer : d) 60
Description : Find the potential due to a charged ring of density 2 units with radius 2m and the point at which potential is measured is at a distance of 1m from the ring. a) 18π b) 24π c) 36π d) 72π
Last Answer : d) 72π
Description : Why the peak voltage not exactly equal to the alternating peak voltage?
Last Answer : Need answer
Description : If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?
Last Answer : Iavg = 0.636 × Imax = 1.41 amperes.
Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value
Last Answer : b) Equal to DC value
Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.
Description : Standing waves occurs due to a) Impedance match b) Impedance mismatch c) Reflection d) Transmission
Last Answer : b) Impedance mismatch
Description : Calculate the transmission coefficient of a wave with a reflection coefficient of 0.6 a) 0.6 b) 1 c) 0 d) 0.4
Last Answer : d) 0.4
Description : The transmission coefficient of a wave with incident and transmitted electric field of 5 and 5 respectively is a) 0 b) 1 c) 10 d) 5
Last Answer : b) 1
Description : The angle of incidence of a wave of a wave with angle of transmission 45 degree and the refractive indices of the two media given by 2 and 1.3 is a) 41.68 b) 61.86 c) 12.23 d) 27.89
Last Answer : a) 41.68
Description : The Brewster angle is the angle of a) Incidence b) Reflection c) Refraction d) Transmission
Last Answer : a) Incidence
Description : The transmission coefficient of a wave propagating in the Brewster angle is a) 0 b) 1 c) -1 d) Infinity
Description : The work done in the power transmission with E and H given by 50 and 65 respectively. The velocity of propagation is 20m/s. a) 162.5 b) 621.5 c) 562.1 d) 261.5
Last Answer : a) 162.5
Description : The velocity of a wave travelling in the air medium without transmission lines or waveguides(wireless) is a) 6 x 10 8 b) 3 x 10 8 c) 1.5 x 10 8 d) 9 x 10 8
Last Answer : b) 3 x 10 8
Description : If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses
Last Answer : d) Reversed Stresses
Description : The current reflection coefficient of a line with voltage reflection coefficient of 0.65 is given by a) 0 b) 0.65 c) -0.65 d) 0.35
Last Answer : c) -0.65