Can I use eurometer calibrated in RMS to measure HWDC in peak?

Can I use eurometer calibrated in RMS to measure HWDC in peak?
by

1 Answer

Answer :

No
by

Related questions

AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Description : AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Last Answer : Answer: C

In AC circuits, AC meters measure – (1) mean values (2) rms values (3) peak values (4) mean square values

Description : In AC circuits, AC meters measure – (1) mean values (2) rms values (3) peak values (4) mean square values

Last Answer : (2) rms values Explanation: Voltages and currents for AC circuits are generally expressed as rms (root mean square) values. For a sine wave, the relationship between the peak and the rms average is: rms value = 0.707 peak value.

In AC circuits, AC meters measure (1) mean values (2) rms values (3) peak values (4) mean square values

Description : In AC circuits, AC meters measure (1) mean values (2) rms values (3) peak values (4) mean square values

Last Answer : rms values

Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Description : Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Last Answer : Answer: B

If digital DRT is calibrated for 300 mm longitudinal wave using 00 double crystal probe then 60kg rail ---------peak will appear at (i) 5.2 (ii) 5.7* (iii) 7.8 (iv) 8.6

Description : If digital DRT is calibrated for 300 mm longitudinal wave using 00 double crystal probe then 60kg rail ---------peak will appear at (i) 5.2 (ii) 5.7* (iii) 7.8 (iv) 8.6

Last Answer : ii) 5.7*

What equipment uses a calibrated resonant circuit to measure frequency?

Description : What equipment uses a calibrated resonant circuit to measure frequency?

Last Answer : Wavemeter.

What does the Voltmeter in AC mode show? Is it RMS value or peak value?

Description : What does the Voltmeter in AC mode show? Is it RMS value or peak value?

Last Answer : Multimeter in AC mode shows RMS value of the voltage or current. Also when it is DC mode it will show the RMS value only.

External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Last Answer : D. peak values

Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Description : Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Last Answer : c) RMS value

The voltage at any point in an ac circuit will be a) Peak voltage b) RMS voltage c) Average voltage d) Source voltage

Description : The voltage at any point in an ac circuit will be a) Peak voltage b) RMS voltage c) Average voltage d) Source voltage

Last Answer : b) RMS voltage

If the peak value of a sine wave is 30 V, the rms value is?

Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -

Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -  a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA

Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA

For ultrasonic testing, which of the following statements is true? a) It is easy to identify all defects b) The equipment shall be calibrated before use c) The equipment cannot be automated d) Sound waves will not travel through copper

Description : For ultrasonic testing, which of the following statements is true? a) It is easy to identify all defects b) The equipment shall be calibrated before use c) The equipment cannot be automated d) Sound waves will not travel through copper

Last Answer : b) The equipment shall be calibrated before use

What are some examples when the word calibrated is used in a lay person's life?

Description : What are some examples when the word calibrated is used in a lay person's life?

Last Answer : TV screen – to make the picture display correctly. Printer – to make the different colours align. Oven with an oven thermometer – to make sure it’s at the temperature you think it’s at. Laptop battery – so that the display gives an accurate readout of how much powered left. A cars wheel alignment.

What's the process by which the line of sight from a scope and the path of a bullet from a rifle is calibrated?

Description : What's the process by which the line of sight from a scope and the path of a bullet from a rifle is calibrated?

Last Answer : In mechanics, I studied this. Trajectory or path of the bullet is parabolic. You may read Rifle Bullet Trajectory. Rifle shooting tips Rifle Trajectory Table Parts of a trajectory

How a thermometer is calibrated?

Description : How a thermometer is calibrated?

Last Answer : How a thermometer is calibrated?

What calibrated tool was the standard tool for engineers and scientists prior to the invention of the hand-held calculator?

Description : What calibrated tool was the standard tool for engineers and scientists prior to the invention of the hand-held calculator?

Last Answer : Slide rule

The most effective method of locating a loose commutator bar in a D.C. motor is by _____________. A. visual inspection B. jiggling each by hand C. sounding each bar with a light weight hammer D. checking with a calibrated torque wrench

Description : The most effective method of locating a loose commutator bar in a D.C. motor is by _____________. A. visual inspection B. jiggling each by hand C. sounding each bar with a light weight hammer D. checking with a calibrated torque wrench

Last Answer : Answer: C

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B

When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. adjusting the line voltage to calibrate the instrument C. plugging each end of one test lead into the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit voltage test of individual cells C. visually inspecting the electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Description : When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit ... electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Last Answer : Answer: A

A capacitor discolored due to excessive heat should be _____________. A. calibrated B. replaced C. cooled D. soldered

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated B. replaced C. cooled D. soldered

Last Answer : Answer: B

Explain How Can A D.p. Transmitter Be Calibrated?

Description : Explain How Can A D.p. Transmitter Be Calibrated?

Last Answer : D.P. transmitter can be calibrated using following steps: 1. Adjust zero of Xmtrs. 2. Perform static pressure test: Give equal pressure on both sides of transmitter. Zero should not shift either ... Apply required pressure to the high pressure side and adjust the span. Adjust zero gain if necessary.

How Can A D.p. Transmitter Be Calibrated?

Description : How Can A D.p. Transmitter Be Calibrated?

Last Answer : D.P. transmitter can be calibrated using following steps: 1. Adjust zero of Transmitter. 2. Perform static pressure test: Give equal pressure on both sides of transmitter. Zero should not ... Apply required pressure to the high pressure side and adjust the span. Adjust zero gain if necessary.

An instrument that must be calibrated in place requires what type of calibration label?

Description : An instrument thAn instrumAn instrument that must be calibrated in place requires what type of calibration label?

Last Answer : SPECIAL CALIBRATION label.

For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Description : For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Last Answer : vertical

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : b. Light power out of a fiber

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : ∙ b. Light power out of a fiber

How can a periodontal pocket be recognised:** A. X-Ray B. Periodontal probe / Calibrated probe C. Periodontal marker D. Bitewing radiograph E. Sharp explorer F. Study cast

Description : How can a periodontal pocket be recognised:** A. X-Ray B. Periodontal probe / Calibrated probe C. Periodontal marker D. Bitewing radiograph E. Sharp explorer F. Study cast

Last Answer : B. Periodontal probe / Calibrated probe

How to measure peak flow?

Description : How to measure peak flow?

Last Answer : Move the marker to the bottom of the numbered scale.Stand up straight.Take a deep breath. Fill your lungs all the way.Hold your breath while you place the mouthpiece in your mouth, between your teeth. Close ... of Medicine. Also reviewed by David Zieve, MD, MHA, Medical Director, A.D.A.M., Inc.

What is Rate Monotonic Scheduling (RMS) ? when its use recommended ?

Last Answer : There are two main types of task scheduling algorithm in Real-Time Operating Systems (RTOS).1. Rate Monotonic Scheduling (RMS)2. Earliest-Deadline-First (EDF)Rate Monotonic Scheduling ( ... shortest period process and so on.Rate Monotonic Scheduing do not support non-periodic processees.

Was the SS Empress of Russia the same ship as the RMS Empress of Russia?

Description : Was the SS Empress of Russia the same ship as the RMS Empress of Russia?

Last Answer : This ship was built at Fairfields on the Clyde in 1913. It was scrapped in 1945. There is a model of the ship in the Glasgow Transport Museum. The Empress of Russia was a steamship and so the ... RMS for Royal Mail Ship to indicate when it was carrying mail under contract to the British Royal Mail

What does RMS mean relating to car speakers?

Description : What does RMS mean relating to car speakers?

Last Answer : RMS= Root Mean Square.

I've been asked to find the temperature to which a 20.0°C gas must be raised to increase its root mean square (rms) speed by a given percentage. Is this possible without knowing the identity of the gas?

Description : I've been asked to find the temperature to which a 20.0°C gas must be raised to increase its root mean square (rms) speed by a given percentage. Is this possible without knowing the identity of the gas?

Last Answer : Pretend the gas is hydrogen. Work out the problem. Pretend the gas is oxygen. Work out the problem. Are the answers you get any different?

What is the difference between SS/HMS/RMS on a boat?

Description : What is the difference between SS/HMS/RMS on a boat?

Last Answer : SS [equal] steam ship HMS [equal] Her/His Majesty’s Ship Edit – forgot to add RMS [equal] Royal Mail Ship/Steamer

What is the full form of 'RMS' ? -How To ?

Description : What is the full form of 'RMS' ? -How To ?

Last Answer : The full form of 'RMS' is Railway Mail Service

Why did the RMS titanic sink in 1912 on April 15th?

Description : Why did the RMS titanic sink in 1912 on April 15th?

Last Answer : Adélie penguins live along with the coastal areas of Antarctica. They usually live on sea ice for easy access to food, but they move to ice-free inland areas to breed during the summer. The ... The warmer temperature will allow plants to grow inland. Penguins will switch to plants as their food sour

What is RMS value ?

Description : What is RMS value ?

Last Answer : If a certain amount of heat is generated in a certain amount of DC current flows through a certain register at a certain time , if the same amount of heat is generated in the current flowing through the ... at the same time, then that DC current is called the effective or RMS value of AC current.

What is the full form of RMS ?

Description : What is the full form of RMS ?

Last Answer : Full form of RMS Railway Mail Service.

What is the full form of RMS ?

Last Answer : RMS - Railway Mail Service

What is RMS of gas ?

Last Answer : : The average square velocity of a gas molecule is called RMS velocity in English.

RMS stands for A. Railway mail sell B. Railway mail service C. Railway mail stop D. Railway mail sound

Description : RMS stands for A. Railway mail sell B. Railway mail service C. Railway mail stop D. Railway mail sound

Last Answer : B [Railway mail service]

The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Description : The RMS value of a sine-wave current may also be expressed as the _____________. A. average value B. maximum value C. effective value D. instantaneous value

Last Answer : Answer: C

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

ECE Board Exam March 1996 The potential difference between any exposed structured to ground in any electrical installation should not exceed _________ volts RMS. A. 10 B. 45 C. 0 D. 30

Description : ECE Board Exam March 1996 The potential difference between any exposed structured to ground in any electrical installation should not exceed _________ volts RMS. A. 10 B. 45 C. 0 D. 30

Last Answer : B. 45

In case of inward unpaid foreign mails, the article can be taxed a) By any post office b) by only the Head Post office c) By the office of exchange in India d) By the RMS office only

Description : In case of inward unpaid foreign mails, the article can be taxed a) By any post office b) by only the Head Post office c) By the office of exchange in India d) By the RMS office only

Last Answer : c) By the office of exchange in India

When a VP article is redirected, intimation should be served to a) Office of posting b) The addressee c) The sender d) The concerned RMS

Description : When a VP article is redirected, intimation should be served to a) Office of posting b) The addressee c) The sender d) The concerned RMS

Last Answer : a) Office of posting