The skin depth is measured in a) Meter b) Millimetre c) Centimetre d) Micrometer

The skin depth is measured in
a) Meter
b) Millimetre
c) Centimetre
d) Micrometer
by

1 Answer

Answer :

d) Micrometer
by

Related questions

Stress may be expressed in Newtons (A) Per millimetre square (N/mm2 ) (B) Per centimetre square (N/cm2 ) (C) Per metre square (N/m2 ) (D) None of these

Description : Stress may be expressed in Newtons  (A) Per millimetre square (N/mm2 )  (B) Per centimetre square (N/cm2 )  (C) Per metre square (N/m2 )  (D) None of these 

Last Answer : (A) Per millimetre square (N/mm2 )

The heights of 50 students, measured to the nearest centimetre, -Maths 9th

Description : The heights of 50 students, measured to the nearest centimetre, -Maths 9th

Last Answer : Frequency distribution of above data in tabular form is given as: (ii) One conclusion we can draw from the above table is that more than 50% of students are shorter than 165 cm.

Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Last Answer : Answer: C

The skin depth of the wave having a frequency of 3MHz and a velocity of 12 m/s is a) 2 b) 3 c) 4 d) 6

Description : The skin depth of the wave having a frequency of 3MHz and a velocity of 12 m/s is a) 2 b) 3 c) 4 d) 6

Last Answer : c) 4

The relation between the skin depth and frequency is given by a) Skin depth α f b) Skin depth α 1/f c) Skin depth α √f d) Skin depth α 1/√f

Description : The relation between the skin depth and frequency is given by a) Skin depth α f b) Skin depth α 1/f c) Skin depth α √f d) Skin depth α 1/√f

Last Answer : d) Skin depth α 1/√f

The skin depth is used to find which parameter? a) DC resistance b) AC resistance c) Permittivity d) Potential

Description : The skin depth is used to find which parameter? a) DC resistance b) AC resistance c) Permittivity d) Potential

Last Answer : b) AC resistance

The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Description : The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Last Answer : a) 4.16 kilo ohm

Calculate the skin depth of a conductor, having a conductivity of 200 units. The wave frequency is 10 GHz in air. a) 355.8 b) 3.558 c) 35.58 d) 0.3558

Description : Calculate the skin depth of a conductor, having a conductivity of 200 units. The wave frequency is 10 GHz in air. a) 355.8 b) 3.558 c) 35.58 d) 0.3558

Last Answer : a) 355.8

The attenuation constant is 0.5 units. The skin depth will be a) 0.5 b) 0.25 c) 2 d) 4

Description : The attenuation constant is 0.5 units. The skin depth will be a) 0.5 b) 0.25 c) 2 d) 4

Last Answer : c) 2

The skin depth is calculated from the amplitude of the wave. State true/false a) True b) False

Description : The skin depth is calculated from the amplitude of the wave. State true/false a) True b) False

Last Answer : a) True

The skin depth of a wave with phase constant of 12 units inside a conductor is a) 12 b) 1/12 c) 24 d) 1/24

Description : The skin depth of a wave with phase constant of 12 units inside a conductor is a) 12 b) 1/12 c) 24 d) 1/24

Last Answer : b) 1/12

The skin depth of a conductor with attenuation constant of 7 neper/m is a) 14 b) 49 c) 7 d) 1/7

Description : The skin depth of a conductor with attenuation constant of 7 neper/m is a) 14 b) 49 c) 7 d) 1/7

Last Answer : d) 1/7

In conductors, which two parameters are same? a) Wavelength and phase constant b) Phase and attenuation constant c) Attenuation constant and skin depth d) Skin depth and wavelength

Description : In conductors, which two parameters are same? a) Wavelength and phase constant b) Phase and attenuation constant c) Attenuation constant and skin depth d) Skin depth and wavelength

Last Answer : b) Phase and attenuation constant

Skin depth phenomenon is found in which materials? a) Insulators b) Dielectrics c) Conductors d) Semiconductors

Description : Skin depth phenomenon is found in which materials? a) Insulators b) Dielectrics c) Conductors d) Semiconductors

Last Answer : c) Conductors

Calculate the phase constant of a wave with skin depth of 2.5 units. a) 5/2 b) 5 c) 2 d) 2/5

Description : Calculate the phase constant of a wave with skin depth of 2.5 units. a) 5/2 b) 5 c) 2 d) 2/5

Last Answer : d) 2/5

Calculate the skin depth of a material with attenuation constant of 2 units. a) 2 b) 1 c) 0.5 d) 4

Description : Calculate the skin depth of a material with attenuation constant of 2 units. a) 2 b) 1 c) 0.5 d) 4

Last Answer : c) 0.5

Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Description : Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Last Answer : vernier callipers

State advantages & disadvantages of electromagnetic flow meter.

Description : State advantages & disadvantages of electromagnetic flow meter.

Last Answer : Advantage: Provides wide linear range. 2) Ability to measure reverses flow. 3) Gives rapid response to flow changes. 4) No obstruction is created to flow. 5) It can handle corrosive as ... and pipe networks with relatively short inside diameters. 3) It is useful for electrically conducting fluid.

Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Description : Alternating current measured in a transmission line will be a) Peak value b) Average value c) RMS value d) Zero

Last Answer : c) RMS value

Find the angle at which the potential due a dipole is measured, when the distance from one charge is 12cm and that due to other is 11cm, separated to each other by a distance of 2cm. a) 15 b) 30 c) 45 d) 60

Description : Find the angle at which the potential due a dipole is measured, when the distance from one charge is 12cm and that due to other is 11cm, separated to each other by a distance of 2cm. a) 15 b) 30 c) 45 d) 60

Last Answer : d) 60

Compute the power consumed by a material with current density 15 units in an area of 100 units. The potential measured across the material is 20V. a) 100kJ b) 250kJ c) 30kJ d) 15kJ

Description : Compute the power consumed by a material with current density 15 units in an area of 100 units. The potential measured across the material is 20V. a) 100kJ b) 250kJ c) 30kJ d) 15kJ

Last Answer : c) 30kJ

Find the potential due to a charged ring of density 2 units with radius 2m and the point at which potential is measured is at a distance of 1m from the ring. a) 18π b) 24π c) 36π d) 72π

Description : Find the potential due to a charged ring of density 2 units with radius 2m and the point at which potential is measured is at a distance of 1m from the ring. a) 18π b) 24π c) 36π d) 72π

Last Answer : d) 72π

What is the name of 300 MHz of unlicensed spectrum allocated by FCC in ISM band? a) UNII b) Unlicensed PCS c) Millimetre wave d) Bluetooth

Description : What is the name of 300 MHz of unlicensed spectrum allocated by FCC in ISM band? a) UNII b) Unlicensed PCS c) Millimetre wave d) Bluetooth

Last Answer : a) UNII

The unit of measurement of a word length is (1) Metre (2) Byte (3) Bit (4) Millimetre

Description : The unit of measurement of a word length is (1) Metre (2) Byte (3) Bit (4) Millimetre

Last Answer : Bit

A 10 C of charge flows through a wire in 5 minutes. The radius of the wire is 1 mm. It contains `5xx10^(22)` electrons per `"centimetre"^(3)`. Calcula

Description : A 10 C of charge flows through a wire in 5 minutes. The radius of the wire is 1 mm. It contains `5xx10^(22)` electrons per `"centimetre"^(3)`. Calcula

Last Answer : A 10 C of charge flows through a wire in 5 minutes. The radius of the wire is 1 mm. It ... centimetre"^(3)`. Calculate the current and drift velocity.

Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Description : Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Last Answer : (D) Surface area per unit mass

The skin effect is a phenomenon observed in a) Insulators b) Dielectrics c) Conductors d) Semiconductors

Description : The skin effect is a phenomenon observed in a) Insulators b) Dielectrics c) Conductors d) Semiconductors

Last Answer : c) Conductors

Who invented the micrometer ?

Last Answer : : Gasquizin invented the micrometer.

What is difference between micrometer and screw gauge?

Description : What is difference between micrometer and screw gauge?

Last Answer : There is no difference - they're different names for the samedevice.

What is the smallest part of a centimeter that can be read or estimated with micrometer caliper?

Description : What is the smallest part of a centimeter that can be read or estimated with micrometer caliper?

Last Answer : What is the answer ?

Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Description : Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Last Answer : Answer: D

What is the least count of out-side micrometer?

Description : What is the least count of out-side micrometer?  

Last Answer : The least count of out-side micrometer is 0.01mm. 

A scrubber in the exhaust of a chemical industrial plant removes (a) gases like sulphur dioxide (b) particulate matter of the size 5 micrometer or above (c) gases like ozone and methane (d) particulate matter of the size 2.5 micrometer or less.

Description : A scrubber in the exhaust of a chemical industrial plant removes (a) gases like sulphur dioxide (b) particulate matter of the size 5 micrometer or above (c) gases like ozone and methane (d) particulate matter of the size 2.5 micrometer or less.

Last Answer : a) gases like sulphur dioxide

Soil strength is determined by (a) Penetrometer (b) Micrometer (c) Hydrometer (d) Dynamometer

Description : Soil strength is determined by (a) Penetrometer (b) Micrometer (c) Hydrometer (d) Dynamometer

Last Answer : (a) Penetrometer

Particles having diameter greater than 75 μm (micrometer = 10 -6 mm) are called (A) Grit (B) Dust (C) Powder (D) Smoke

Description : Particles having diameter greater than 75 μm (micrometer = 10 -6 mm) are called (A) Grit (B) Dust (C) Powder (D) Smoke

Last Answer : (A) Grit

Single-mode step-index cable has a core diameter in the range of ∙ A. 100 to 1000 micrometer ∙ B. 50 to 100 micrometer ∙ C. 2 to 15 micrometer ∙ D. 5 to 20 micrometer

Description : Single-mode step-index cable has a core diameter in the range of ∙ A. 100 to 1000 micrometer ∙ B. 50 to 100 micrometer ∙ C. 2 to 15 micrometer ∙ D. 5 to 20 micrometer

Last Answer : . 2 to 15 micrometer

A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer

Description : A popular light wavelength fiber-optic cable is ∙ A. 0.7 micrometer ∙ B. 1.3 micrometer ∙ C. 1.5 micrometer ∙ D. 1.8 micrometer

Last Answer : B. 1.3 micrometer

What is the unit of light wavelength? ∙ a. Micrometer ∙ b. Angstroms ∙ c. Mils ∙ d. Fathom

Description : What is the unit of light wavelength? ∙ a. Micrometer ∙ b. Angstroms ∙ c. Mils ∙ d. Fathom

Last Answer : ∙ b. Angstroms

Soil strength is determined by: A. penetrometer B. micrometer C. hydrometer D. dynamometer

Description : Soil strength is determined by: A. penetrometer B. micrometer C. hydrometer D. dynamometer

Last Answer : D. dynamometer

What type of wave has a wavelength of 3 m forms in water with a depth of one meter?

Description : What type of wave has a wavelength of 3 m forms in water with a depth of one meter?

Last Answer : Need answer

If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Description : If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Last Answer : Answer: Option D

The average mean velocity of a stream having depth h, may be obtained by taking the average of the readings of a current meter at a depth of (A) 0.1 h and 0.9 h (B) 0.2 h and 0.8 h (C) 0.3 h and 0.7 h (D) 0.4 h and 0.6 h

Description : The average mean velocity of a stream having depth h, may be obtained by taking the average of the readings of a current meter at a depth of (A) 0.1 h and 0.9 h (B) 0.2 h and 0.8 h (C) 0.3 h and 0.7 h (D) 0.4 h and 0.6 h

Last Answer : Answer: Option B

A hydraulic jump in a control meter will be formed above the control, if its original (A) Depth is more than critical depth (B) Depth is less than the critical depth (C) Depth is equal to critical depth (D) None of these

Description : A hydraulic jump in a control meter will be formed above the control, if its original (A) Depth is more than critical depth (B) Depth is less than the critical depth (C) Depth is equal to critical depth (D) None of these

Last Answer : Answer: Option B

For efficient working of a control meter, its throat length is approximately kept (A) Equal to the critical depth (B) Twice the critical depth (C) Three times the critical depth (D) Four times the critical depth

Description : For efficient working of a control meter, its throat length is approximately kept (A) Equal to the critical depth (B) Twice the critical depth (C) Three times the critical depth (D) Four times the critical depth

Last Answer : Answer: Option C

The critical depth meter is used to measure (A) Velocity of flow in an open channel (B) Depth of flow in an open channel (C) Hydraulic jump (D) Depth of channel

Description : The critical depth meter is used to measure (A) Velocity of flow in an open channel (B) Depth of flow in an open channel (C) Hydraulic jump (D) Depth of channel

Last Answer : Answer: Option C

nstrument used for measuring the depth & width of ploughing : A. penetrometer B. width meter C. depth meter D. width and depth meter

Description : nstrument used for measuring the depth & width of ploughing : A. penetrometer B. width meter C. depth meter D. width and depth meter

Last Answer : A. penetrometer

A wave with a wavelength of 40 meters and a height of 2 meters will NOT be refracted in water with a depth of more than: w) 1 meter x) 2 meters y) 10 meters z) 20 meters

Description : A wave with a wavelength of 40 meters and a height of 2 meters will NOT be refracted in water with a depth of more than: w) 1 meter x) 2 meters y) 10 meters z) 20 meters

Last Answer : ANSWER: Z -- 20 METERS

A concrete dam 15 m deep and 2 m wide containing water to a depth of 10 m .Find total hydrostatic pressure per meter run and centre of pressure on upstream face.

Description : A concrete dam 15 m deep and 2 m wide containing water to a depth of 10 m .Find total hydrostatic pressure per meter run and centre of pressure on upstream face.

Last Answer : A concrete dam 15 m deep and 2 m wide containing water to a depth of 10 m .Find total hydrostatic pressure per meter run and centre of pressure on upstream face.

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned

Description : A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

Last Answer : A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is 200µNm