The current in a given circuit is not to exceed 24 A. Which value of fuse is best ?

by

1 Answer

Answer :

Better u have to install 24 amps fuse.
by

Related questions

If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : -

Description :  If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : -  a) fails to build up b) builds up a very high voltage c) exceeds its current capacity d) produces power beyond its rating 

Last Answer :  If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : - fails to build up 

Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Description : Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Last Answer : Ans: A

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current

Description : The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current

Last Answer : Ans:(c)

The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Description : The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Last Answer : (2) Current Explanation: In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a sacrificial device to provide over protection, of either the load ... fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented.

A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Last Answer : (2) Fuse Explanation: A fuse places a limit on the amount of current that can be drawn by an electric circuit by opening (blowing or melting) when the current exceeds a preset limit. This protects the circuit and the surroundings from fire or damage in the case of an overload or short circuit.

An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected

Description : An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected

Last Answer : Answer: A

A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Description : A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Last Answer : Answer: B

A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor 

Last Answer : Fuse

A fuse is always installed in a circuit is

Last Answer : A fuse is always installed in a circuit is Series.

To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Description : To ensure constant moisture content in aggregates (A) Area of each aggregate pile should be large (B) Height of each aggregate pile should not exceed 1.50 m (C) Aggregate pile should be left for 24 hours before aggregates are used (D) All the above

Last Answer : Answer: Option D

Consider the following statements: Maximum slenderness ratio of load-bearing masonry walls for a dwelling having more than two storeys shall not exceed. 1. 12, if lime mortar is used 2. 18, if cement-lime mortar 1:2:9 is used 3. 24, if cement mortar 1:6 is used\ Which of these statements are correct? (a) 1 and 2 only b) 2 and 3 only c) 1 and 3 only d)1, 2 and 3

Description : Consider the following statements: Maximum slenderness ratio of load-bearing masonry walls for a dwelling having more than two storeys shall not exceed. 1. 12, if lime mortar is used 2. 18, if cement-lime mortar 1:2:9 is used 3. 24, ... ? (a) 1 and 2 only b) 2 and 3 only c) 1 and 3 only d)1, 2 and 3

Last Answer : b) 2 and 3 only

The maximum time lag between surface preparation and the application of primer coat shall not exceed a) 12 hours b) 24 hours* c) 48 hours d) 36 hours

Description : The maximum time lag between surface preparation and the application of primer coat shall not exceed a) 12 hours b) 24 hours* c) 48 hours d) 36 hours

Last Answer : b) 24 hours*

There are 50 compartments in a Chennai express carrying an average of 70 passengers per compartments. At least 24 passengers were sitting in each compartment, not any compartment has equal number of passengers, and any compartment does not exceed the number of average passengers expect 50th compartment. Find how many passengers can be accommodated in 50th compartment? A. 748 B. 705 C.739 D.cannot be determined

Description :  There are 50 compartments in a Chennai express carrying an average of 70 passengers per compartments. At least 24 passengers were sitting in each compartment, not any compartment has equal number of passengers, ... can be accommodated in 50th compartment? A. 748 B. 705 C.739 D.cannot be determined 

Last Answer : C) Total number of passengers in Chennai express = 50*70 = 3500 Total number of candidates from 1 to 49 compartments = 24+25+....+70 = (70*71)/2 +(23*24)/2 = 2761 number of passengers in 50th compartment = 3500 - 2761= 739

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Last Answer : Answer: C

In the illustrated circuit, what is the resistance of R2 if the total current is .75 amps, the voltage is 12 VDC and the resistance of R1 is 24 ohms? EL-0019 A. 24 ohms B. 16 ohms C. 48 ohms D. the answer can not be determined from the information given

Description : In the illustrated circuit, what is the resistance of R2 if the total current is .75 amps, the voltage is 12 VDC and the resistance of R1 is 24 ohms? EL-0019 A. 24 ohms B. 16 ohms C. 48 ohms D. the answer can not be determined from the information given

Last Answer : Answer: C

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Last Answer : Answer: A

Periodic testing of circuit breakers is necessary to assure that a correctly rated and properly installed unit _________________. A. can trip faster as it increases in age B. will continue to provide the original degree of protection C. does not exceed its interrupting capacity D. be able to withstand at least 125% of applied voltage

Description : Periodic testing of circuit breakers is necessary to assure that a correctly rated and properly installed unit _________________. A. can trip faster as it increases in age B. will continue to provide ... not exceed its interrupting capacity D. be able to withstand at least 125% of applied voltage

Last Answer : Answer: B

The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Description : The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Last Answer : B. 1 dB

The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Last Answer : 10 to 1

What is the difference between a fuse and a circuit breaker ?

Description : What is the difference between a fuse and a circuit breaker ?

Last Answer : Fuse : It is a type of soft metal wire which, when more than the required current flows through the wire, burns it, disconnects the electrical circuit from the source and protects the valuable ... or fault in the power supply line . This breaks the static contact and protects it from accidents.

Which covalent fuse wire is connected to the main circuit ?

Description : Which covalent fuse wire is connected to the main circuit ?

Last Answer : The fuse wire is connected to the main circuit in a class co-op.

A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Description : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Last Answer : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of ... on, is A. 11 B. 22 C. 33 D. 66

Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Description : Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Last Answer : The load exceeds the limit of the breaker or fuse. For example a20 amp breaker on a 120 volt circuit will handle 2400 watts. Exceedthat wattage and the breaker will trip or the fuse will blow.

The fuse in an electric circuit is connected in

Description : The fuse in an electric circuit is connected in

Last Answer : series with the live wire

In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Description : In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Last Answer : Ans:(a)

The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Description : The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Last Answer : (4) series with live Explanation: A fuse wire is a safety wire connected in series with the live wire that has high resistivity and low melting point. Fuses are always connected in ... large current supply or malfunctioning in the electric connections, it melts and breaks the electric circuit.

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Last Answer : Answer: C

In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' and '3' would would burn dimly, while branch '2' would burn normally C. '1', '2', and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Last Answer : Answer: D

The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Last Answer : Answer: D

In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Description : In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Last Answer : Answer: B

If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Description : If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Last Answer : Answer: C

When testing for blown fuses in a three-phase supply circuit to a motor, you should first ___________________. A. apply the megger across the tops of the line fuses B. apply an ammeter diagonally across the top of the first line fuse and the bottom of the third line fuse C. apply the voltage tester across the bottoms of the line fuses D. ensure the circuit is de-energized, and then use a continuity tester

Description : When testing for blown fuses in a three-phase supply circuit to a motor, you should first ___________________. A. apply the megger across the tops of the line fuses B. apply an ammeter diagonally across ... of the line fuses D. ensure the circuit is de-energized, and then use a continuity tester

Last Answer : Answer: D

When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Description : When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Description : A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Last Answer : Answer: B

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Description : If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Last Answer : Answer: C

You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. Testing an energized circuit presents a hazard to the testing personnel. B. A faulty fuse could go undetected with the motor energized. C. Reversed polarity of the circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Description : You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. ... circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Last Answer : Answer: B

Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Last Answer : Answer: D

Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor is started. B. The fuse works, but overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Description : Which of the following conditions is most likely to occur if a single element fuse were used to replace a blown dual element fuse in a motor controller circuit? A. The fuse will blow when the motor ... overheats at high motor loads. C. The motor runs at reduced voltage. D. The motor runs normally.

Last Answer : Answer: A

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

Which of the listed items will stop a motor due to a reduction in voltage and restart it when the voltage is restored to normal? A. Low voltage protection circuit B. Non-renewable link fuse C. Renewable link fuse D. Low voltage release circuit

Description : Which of the listed items will stop a motor due to a reduction in voltage and restart it when the voltage is restored to normal? A. Low voltage protection circuit B. Non-renewable link fuse C. Renewable link fuse D. Low voltage release circuit

Last Answer : Answer: D

The part of a fuse that melts and opens the circuit is made of _____________. A. copper and antimony B. steel and babbitt C. aluminum or beryllium alloy D. zinc or an alloy of tin and lead

Description : The part of a fuse that melts and opens the circuit is made of _____________. A. copper and antimony B. steel and babbitt C. aluminum or beryllium alloy D. zinc or an alloy of tin and lead

Last Answer : Answer: D

A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Description : A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Last Answer : Answer: B

A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : Link is provided at a Neutral common point in the circuit from which various connections are taken for the individual control circuit and so it is given in a link form to withstand high Amps. ... So if any malfunction happens the fuse connected in the particular control circuit alone will blow off.

Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Description : Why link is provided in neutral of an ac circuit and fuse in phase of ac circuit?

Last Answer : A:Link is provided at a Neutral common point in the circuit from which various connection are taken for the individual control circuit and so it is given in a link form to withstand high Amps ... .So if any malfunction happen the fuse connected in the particular control circuit alone will blow off.