The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current

The function of fuse in an electrical circuit is (a) avoid electric shocks (b) regulate the flow of current (c) break the circuit in case of overloading or short circuiting (d) switch off current
by

1 Answer

Answer :

Ans:(c)
by
selected

Related questions

An electrical appliance is earthed to 1. Protect the appliance against any damage 2. Prevent electric shocks 3. Avoid short-circuiting Which of the above is/are correct? (a) 1 only (b) 2 only (c) 1 and 2 (d) 2 and 3

Description : An electrical appliance is earthed to 1. Protect the appliance against any damage 2. Prevent electric shocks 3. Avoid short-circuiting Which of the above is/are correct? (a) 1 only (b) 2 only (c) 1 and 2 (d) 2 and 3

Last Answer : Ans:(b)

A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Last Answer : Answer: C

In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open connections while testing C. test the windings as parallel groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Description : In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open ... groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Last Answer : Answer: D

The primary function of carbohydrates is to: a) break down molecules. b) aid in digestion. c) supply the body with energy. d) regulate the flow of chyme.

Description : The primary function of carbohydrates is to: a) break down molecules. b) aid in digestion. c) supply the body with energy. d) regulate the flow of chyme.

Last Answer : ANSWER: C -- SUPPLY THE BODY WITH ENERGY.

3. What precaution should be taken to avoid the overloading of domestic electric circuits? -Physics-10

Description : 3. What precaution should be taken to avoid the overloading of domestic electric circuits? -Physics-10

Last Answer : A few of the precautions to be taken to avoid the overloading of domestic electric circuits are as follows: Connecting too many devices to a single socket should be avoided Using too many appliances at the same time should be avoided Faulty appliances should not be connected to the circuit

When one turns off the car with out powering down the a/c, fan, and radio does it contribute to short circuiting?

Description : When one turns off the car with out powering down the a/c, fan, and radio does it contribute to short circuiting?

Last Answer : As long as the car is operating correctly, none of these actions will cause any harm. Manufacturers do not expect you to power down everything before shutting off the car.

Under what condition, the current passing through the resistance R can be increased by short - circuiting the battery of emf `E_2` The internal resist

Description : Under what condition, the current passing through the resistance R can be increased by short - circuiting the battery of emf `E_2` The internal resist

Last Answer : Under what condition, the current passing through the resistance R can be increased by short - circuiting the battery of ... (1)r_(2)gtE_(2)(R+r_(1))`

is the application of sprayer. a) To break the liquid droplet of effective size b) To distribute them uniformly event plants c) To regulate amount of liquid to avoid excessive application. d) All above them

Description : is the application of sprayer. a) To break the liquid droplet of effective size b) To distribute them uniformly event plants c) To regulate amount of liquid to avoid excessive application. d) All above them

Last Answer : All above them

The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Description : The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Last Answer : Answer: A

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a - (1) Grid (2) Fuse (3) Hub (4) Conductor

Last Answer : (2) Fuse Explanation: A fuse places a limit on the amount of current that can be drawn by an electric circuit by opening (blowing or melting) when the current exceeds a preset limit. This protects the circuit and the surroundings from fire or damage in the case of an overload or short circuit.

A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor

Description : A device which is used to limit the current in an electrical circuit is called a (1) Grid (2) Fuse (3) Hub (4) Conductor 

Last Answer : Fuse

An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. positive deflection of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Description : An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. ... of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Last Answer : Answer: C

Which of the following is a characteristic of fractional horsepower repulsion start motors? A. They start with a rotating stator field. B. The short circuiting ring is removed from the commutator while starting. C. The brushes are removed from the commutator while starting. D. They have a low starting torque.

Description : Which of the following is a characteristic of fractional horsepower repulsion start motors? A. They start with a rotating stator field. B. The short circuiting ring is removed from the commutator while ... brushes are removed from the commutator while starting. D. They have a low starting torque.

Last Answer : Answer: B

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Last Answer : Answer: C

Temporary repairs to an open DC propulsion armature coil can be made by _____________. A. connecting the coil ends directly to a pair of negative brushes B. disconnecting coil ends, insulating each, and short circuiting the two commutator bars C. grounding the coil ends and short circuiting the commutator bar D. removing the sparking brushes

Description : Temporary repairs to an open DC propulsion armature coil can be made by _____________. A. connecting the coil ends directly to a pair of negative brushes B. disconnecting coil ends, insulating ... C. grounding the coil ends and short circuiting the commutator bar D. removing the sparking brushes

Last Answer : Answer: B

[75] Two transformers are connected in parallel. These transformers do not have equal percentage impedance which results A. Short-circuiting of the secondaries B. Power factor of one of the transformers is leading while that of the other lagging C. Transformers having higher copper losses will have negligible core losses D. Loading of the transformers not in proportion to their kVA ratings.

Description : [75] Two transformers are connected in parallel. These transformers do not have equal percentage impedance which results A. Short-circuiting of the secondaries B. Power factor of one of the ... have negligible core losses D. Loading of the transformers not in proportion to their kVA ratings.

Last Answer : D. Loading of the transformers not in proportion to their kVA ratings

Maximum current will flow through an electrical circuit in case of___________.

Description : Maximum current will flow through an electrical circuit in case of___________. A. Ohm’s Law B. open circuit C. parallel circuit D. Short circuit 

Last Answer : Maximum current will flow through an electrical circuit in case of Short circuit.

Underground cables are laid at sufficient depth (a) to minimise temperature stresses (b) to avoid being unearthed easily due to removal of soil (c) to minimise the effect of shocks and vibrations due to gassing vehicles, etc. (d) for all of the above reasons

Description : Underground cables are laid at sufficient depth (a) to minimise temperature stresses (b) to avoid being unearthed easily due to removal of soil (c) to minimise the effect of shocks and vibrations due to gassing vehicles, etc. (d) for all of the above reasons

Last Answer : (c) to minimise the effect of shocks and vibrations due to gassing vehicles, etc.

The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Description : The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance

Last Answer : (2) Current Explanation: In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a sacrificial device to provide over protection, of either the load ... fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented.

Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Last Answer : Answer: D

Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Description : Which one of the following applications software’s is used to obtain an accurate root locus for? a) LISP b) MATLAB c) dBase d) Oracle Ans: B 6.Lenz devised a rule to find out direction of a)current induced in a circuit b)electromagneticdifference c)potential difference d)flow of power in fuse

Last Answer : Ans: A

A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Description : A circuit breaker and a fuse have a basic similarity in that they both _____________. A. can be reset to energize the circuit B. should open the circuit when overloaded C. will burn out when an over current flow develops D. all of the above

Last Answer : Answer: B

A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

Which of the following is the least expensive protection for overcurrent is low voltage system ? (a) Rewireable fuse (b) Isolator (c) Oil circuit breaker (d) Air break circuit breaker (e) None of the above

Description : Which of the following is the least expensive protection for overcurrent is low voltage system ? (a) Rewireable fuse (b) Isolator (c) Oil circuit breaker (d) Air break circuit breaker (e) None of the above

Last Answer : (a) Rewireable fuse

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

Give the function of fuse and switch.

Description : Give the function of fuse and switch.

Last Answer : Functions of fuse:  * To break the circuit under fault condition.  * To provide overcurrent protection to the circuit.  * To provide short circuit protection to the circuit.  * To provide ...  * To make the electric circuit manually.  * To break the electric circuit manually.

In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL-0007 A. the control fuse is the wrong amperage not allowing full current to pass through B. the stop switch is open C. an open in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Last Answer : Answer: B

In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Description : In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference

Last Answer : Ans:(a)

Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Description : Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?

Last Answer : The load exceeds the limit of the breaker or fuse. For example a20 amp breaker on a 120 volt circuit will handle 2400 watts. Exceedthat wattage and the breaker will trip or the fuse will blow.

Is it true that some fish give electric shocks?

Description : That's probably a fabrication, isn't it? Where would she take the current.

Last Answer : Electric eel live in the waters of South American rivers and swamps. It grows to a length of two and a half meters and a full four-fifths of the length of its body is occupied ... to communicate with each other. http://www.lidovky.cz/jeste-nabitejsi-uhor-0rr-/veda.aspx?c=A081007_084657_ln_veda_mtr

What happens to the current flow if a switch in the circuit is opened-ed?

Description : What happens to the current flow if a switch in the circuit is opened-ed?

Last Answer : What is the answer ?

Blow off cock is provided in steam boiler to (A) Guard the boiler in case of abnormal rise in steam pressure (B) Drain out water and sludge during its repair (C) Regulate the supply of water in boiler (D) Put out the fire in the furnace when the water level in the boiler falls to unsafe limit

Description : Blow off cock is provided in steam boiler to (A) Guard the boiler in case of abnormal rise in steam pressure (B) Drain out water and sludge during its repair (C) Regulate the supply of water in boiler (D) Put out the fire in the furnace when the water level in the boiler falls to unsafe limit

Last Answer : (B) Drain out water and sludge during its repair

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Description : A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Last Answer : Answer: B

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

The fuse in an electric circuit is connected in

Description : The fuse in an electric circuit is connected in

Last Answer : series with the live wire

The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Description : The fuse in an electric circuit is connected in – (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Last Answer : (4) series with live Explanation: A fuse wire is a safety wire connected in series with the live wire that has high resistivity and low melting point. Fuses are always connected in ... large current supply or malfunctioning in the electric connections, it melts and breaks the electric circuit.

If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Description : If an electric motor fails to start, you should FIRST check the _____________. A. phase sequence B. ampere load C. fuse or circuit breaker D. line frequency

Last Answer : Answer: C

You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. Testing an energized circuit presents a hazard to the testing personnel. B. A faulty fuse could go undetected with the motor energized. C. Reversed polarity of the circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Description : You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. ... circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Last Answer : Answer: B

A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Description : A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Last Answer : Answer: B

The fuse in an electric circuit is connected in (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live

Description : The fuse in an electric circuit is connected in (1) series with neutral (2) parallel to live (3) parallel to neutral (4) series with live 

Last Answer : series with live

A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Description : A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Last Answer : Answer: C

A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Description : A transformer in an electric circuit serves to ____________. A. generate its own electrical power B. transform electrical energy into mechanical energy C. increase or decrease circuit voltage as required D. convert AC current to DC current

Last Answer : Answer: C

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps the turn before it C. apply the tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Description : The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps ... tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Last Answer : Answer: B

In a circuit when the electrical resistance increases the current because it is for the electrons to flow.?

Description : In a circuit when the electrical resistance increases the current because it is for the electrons to flow.?

Last Answer : yes