Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Pick out the correct statement.
(A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F
(B) In steady state heat conduction, the only property of the substance which
determines the temperature distribution, is the thermal conductivity
(C) In unsteady state heat conduction, heat flows in the direction of
temperature rise
(D) In heat transfer by forced convection, Grashoff number is very important
by

1 Answer

Answer :

(B) In steady state heat conduction, the only property of the substance which
determines the temperature distribution, is the thermal conductivity
by

Related questions

1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Description : 1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Last Answer : (A) 1.49

A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Description : A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Last Answer : (B) 4.88 kcal/hr. m. 2°C

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced conduction (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Description : When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced ... (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Last Answer : (C) Mixed convection (both free and forced)

The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Description : The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Last Answer : (A) BTU/hr. ft 2°F

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

Unsteady state heat conduction occurs, when (A) Temperature distribution is independent of time (B) Temperature distribution is dependent on time (C) Heat flows in one direction only (D) Three dimensional heat flow is concerned

Description : Unsteady state heat conduction occurs, when (A) Temperature distribution is independent of time (B) Temperature distribution is dependent on time (C) Heat flows in one direction only (D) Three dimensional heat flow is concerned

Last Answer : (B) Temperature distribution is dependent on time

The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the right face is 10 W/m2 .K. At steady state, the temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

View factor is important in heat transfer by (A) Steady state conduction (B) Natural convection (C) Forced convection (D) Radiation

Description : View factor is important in heat transfer by (A) Steady state conduction (B) Natural convection (C) Forced convection (D) Radiation

Last Answer : (D) Radiation

What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Description : What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Last Answer : (B) Kcal/hr.m.°C

The Fourier number (defined as a.t/L 2 ) is used in the analysis of problem involving heat transfer by (A) Forced convection (B) Natural convection(C) Transient conduction(D) Steady state conduction

Description : The Fourier number (defined as a.t/L 2 ) is used in the analysis of problem involving heat transfer by (A) Forced convection (B) Natural convection (C) Transient conduction (D) Steady state conduction

Last Answer : (C) Transient conduction

If heat transfer rate varies with the time, it is termed as (A) Forced convection (B) Steady state conduction (C) Monochromatic radiation (D) None of these

Description : If heat transfer rate varies with the time, it is termed as (A) Forced convection (B) Steady state conduction (C) Monochromatic radiation (D) None of these

Last Answer : (D) None of these

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

In which mode of heat transfer, the Biot number is important? (A) Transient heat conduction (B) Natural convection (C) Forced convection (D) Radiation

Description : In which mode of heat transfer, the Biot number is important? (A) Transient heat conduction (B) Natural convection (C) Forced convection (D) Radiation

Last Answer : (A) Transient heat conduction

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

In a furnace with heating element temperature at 1700°C, the dominant mechanism of heat transfer will be (A) Conduction (B) Radiation (C) Natural convection (D) Forced convection

Description : In a furnace with heating element temperature at 1700°C, the dominant mechanism of heat transfer will be (A) Conduction (B) Radiation (C) Natural convection (D) Forced convection

Last Answer : (B) Radiation

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface temperature follows __________ law. (A) Hyperbolic (B) Parabolic (C) Linear (D) Logarithmic

Description : If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface temperature follows __________ ... (A) Hyperbolic (B) Parabolic (C) Linear (D) Logarithmic

Last Answer : (C) Linear

If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface temperature follows __________ law. (A) Parabolic (B) Hyperbolic (C) Linear (D) Logarithmic

Description : If the thermal conductivity of a wall material is independent of temperature, the steady state temperature distribution in the very large thin plane wall having steady, uniform surface temperature follows __________ law. (A) Parabolic (B) Hyperbolic (C) Linear (D) Logarithmic

Last Answer : (A) Parabolic

Mode of heat transfer in which the fluid moves under the influence of changes in fluid pressure produced by external work is called (A) Radiation (B) Natural convection (C) Forced convection (D) Conduction

Description : Mode of heat transfer in which the fluid moves under the influence of changes in fluid pressure produced by external work is called (A) Radiation (B) Natural convection (C) Forced convection (D) Conduction

Last Answer : (C) Forced convection

Mode of heat transfer involved in the cooling of air cooled internal combustion engine is (A) Conduction(B) Natural convection(C) Forced convection(D) None of these

Description : Mode of heat transfer involved in the cooling of air cooled internal combustion engine is (A) Conduction (B) Natural convection (C) Forced convection (D) None of these

Last Answer : (B) Natural convection

Heat transfer by __________ may not necessarily require the presence of a medium. (A) Conduction (B) Natural convection (C) Forced convection (D) Radiation

Description : Heat transfer by __________ may not necessarily require the presence of a medium. (A) Conduction (B) Natural convection (C) Forced convection (D) Radiation

Last Answer : (D) Radiation

Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Description : Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Last Answer : (B) Density

Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is called the Stanton number (C) The Peclet number is a measure of the ratio of energy transport by convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Description : Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is ... convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Last Answer : (D) The Colburn jH factor for heat transfer is given by Nst Npr

One ton of refrigeration capacity is equivalent to the heat removal rate of (A) 50 kcal/hr (B) 200 BTU/hr (C) 200 BTU/minute

Description : One ton of refrigeration capacity is equivalent to the heat removal rate of (A) 50 kcal/hr (B) 200 BTU/hr (C) 200 BTU/minute

Last Answer : (C) 200 BTU/minute

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Description : Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Last Answer : (A) Prandtl number

Which of the following is unimportant in forced convection? (A) Reynolds number (B) Prandtl number (C) Grashoff number (D) None of these

Description : Which of the following is unimportant in forced convection? (A) Reynolds number (B) Prandtl number (C) Grashoff number (D) None of these

Last Answer : (C) Grashoff number

In natural convection heat transfer, the correlating parameter is the (A) Graetz number (B) Eckert number (C) Grashoff number (D) Bond number

Description : In natural convection heat transfer, the correlating parameter is the (A) Graetz number (B) Eckert number (C) Grashoff number (D) Bond number

Last Answer : (C) Grashoff number

Nusselt number is a function of Prandtl number and __________ number of fluid in natural convection heat transfer. (A) Grashoff (B) Biot (C) Stanton

Description : Nusselt number is a function of Prandtl number and __________ number of fluid in natural convection heat transfer. (A) Grashoff (B) Biot (C) Stanton

Last Answer : (A) Grashoff

Critical value of the __________ number governs the transition from laminar to turbulent flow in free convection heat transfer. (A) Grashoff (B) Reynolds (C) Both 'a' & 'b' (D) Prandtl & Grashoff

Description : Critical value of the __________ number governs the transition from laminar to turbulent flow in free convection heat transfer. (A) Grashoff (B) Reynolds (C) Both 'a' & 'b' (D) Prandtl & Grashoff

Last Answer : (D) Prandtl & Grashoff

Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of (A) Grashoff number (B) Grashoff number & Reynolds number (C) Reynolds number (D) Grashoff number & Prandtl number

Description : Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of (A) Grashoff number (B) Grashoff number & Reynolds number (C) Reynolds number (D) Grashoff number & Prandtl number

Last Answer : Option D

Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the heatcapacity of the substance in the molten state(C) There is an increase in entropy, when a spontaneous change occurs in anisolated system(D) At absolute zero temperature, the heat capacity for many pure crystallinesubstances is zero

Description : Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the ... isolated system (D) At absolute zero temperature, the heat capacity for many pure crystalline substances is zero

Last Answer : (C) There is an increase in entropy, when a spontaneous change occurs in an isolated system

In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Description : In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Last Answer : (C) Radiation

In pipe flow, heat is transferred from hot wall to the liquid by(A) Conduction only (B) Forced convection only (C) Forced convection and conduction (D) Free and forced convection

Description : In pipe flow, heat is transferred from hot wall to the liquid by(A) Conduction only (B) Forced convection only (C) Forced convection and conduction (D) Free and forced convection

Last Answer : (C) Forced convection and conduction

Heat required to raise the temperature of a body by 1 °C is called its (A) Heat capacity (B) Specific heat capacity (C) Thermal conductivity (D) Water equivalent

Description : Heat required to raise the temperature of a body by 1 °C is called its (A) Heat capacity (B) Specific heat capacity (C) Thermal conductivity (D) Water equivalent

Last Answer : (A) Heat capacity

Pick out the wrong statement pertaining to the analogy between equations of heat and mass transfer operations. (A) Sherwood number in mass transfer is analogous to Nusselt number in heat transfer (B) Prandtl number in heat transfer is analogous to Schmidt number in mass transfer (C) Reynolds number in mass transfer is analogous to Grashoff number in heat transfer (D) Reynolds number remains the same in both heat and mass transfer

Description : Pick out the wrong statement pertaining to the analogy between equations of heat and mass transfer operations. (A) Sherwood number in mass transfer is analogous to Nusselt number in heat transfer ... heat transfer (D) Reynolds number remains the same in both heat and mass transfer

Last Answer : (C) Reynolds number in mass transfer is analogous to Grashoff number in heat transfer

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Description : The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C. (A) 768 (B) 908 (C) 1400 (D) 1539

Last Answer : Option A

Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Description : Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Last Answer : (B) For fluids in turbulent flow

In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Description : In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Last Answer : (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section

Maximum heat transfer in high temperature furnaces is by (A) Conduction (B) Convection (C) Radiation (D) Either (A), (B) or (C); depends on the type of furnace

Description : Maximum heat transfer in high temperature furnaces is by (A) Conduction (B) Convection (C) Radiation (D) Either (A), (B) or (C); depends on the type of furnace

Last Answer : (C) Radiation

Forced recirculation of furnace gases is practised (A) To increase heat transfer by convection (B) To ensure uniform temperature (C) In furnaces, operating below 750°C (D) All (A), (B) and (C)

Description : Forced recirculation of furnace gases is practised (A) To increase heat transfer by convection (B) To ensure uniform temperature (C) In furnaces, operating below 750°C (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is important in problems involving gas absorption without chemical reaction (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion (D) Total reflux in case of distillation operation requires infinite number of plates for a binary system separation

Description : Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is ... reflux in case of distillation operation requires infinite number of plates for a binary system separation

Last Answer : (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion

Pick out the wrong statement: (A) With change in temperature, the radiant energy emitted by a black body remains unchanged (B) Absorptivity of a body approaches unity in case of diffuse reflection (C) Absorptivity of a perfectly black body is unity (D) Value of Stefan-Boltzmann constant is 4.876 × 10 -8 KCal/m2 .hr.°K4

Description : Pick out the wrong statement: (A) With change in temperature, the radiant energy emitted by a black body remains unchanged (B) Absorptivity of a body approaches unity in case of diffuse reflection (C) Absorptivity of ... unity (D) Value of Stefan-Boltzmann constant is 4.876 10 -8 KCal/m2 .hr.°K4

Last Answer : (A) With change in temperature, the radiant energy emitted by a black body remains unchanged

Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8 (A) °C (B) °F (C) °K (D) °R

Description : Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8 (A) °C (B) °F (C) °K (D) °R

Last Answer : (B) °F

In forced convection, the heat transfer depends on(A) Re, Pr (B) Re, Gr (C) Mainly Gr (D) Re only

Description : In forced convection, the heat transfer depends on (A) Re, Pr (B) Re, Gr (C) Mainly Gr (D) Re only

Last Answer : (A) Re, Pr