Name the functions of the valve?

Name the functions of the valve? 
by

1 Answer

Answer :

a. ON and OFF service.

b. Throttling or regulating liquid flow.

c. Avoid back flow.

d. Regulating pressure.

e. Relieving pressure. 
by

Related questions

As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Description : As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Last Answer : Answer: B

In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solinoid valve is_________. EL-0043 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad

Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad

Last Answer : Answer: B

In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit is plugged in C. not grounded so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Description : In the illustration, the tan and white wires are connected to the solenoid valve. The solenoid valve is_________. EL-0042 A. in the liquid line before the TXV B. energized and open whenever the unit ... so the unit must be modified before using aboard ship D. the water inlet for the ice maker

Last Answer : Answer: D

Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Last Answer : Answer: C

Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.

Description : Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.

Last Answer : Answer: A

Pin #6 of the ahead valve position sensor as shown in the illustration is connected _______________. EL-0099 A. to (-) 50 volts D.C. B. in parallel with PCOM C. to (+) 50 volts D.C. D. to analog common

Description : Pin #6 of the ahead valve position sensor as shown in the illustration is connected _______________. EL-0099 A. to (-) 50 volts D.C. B. in parallel with PCOM C. to (+) 50 volts D.C. D. to analog common

Last Answer : Answer: C

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

The function of a rectifier is similar to that of a _______. A. trap B. regulating valve C. check valve D. filter

Description : The function of a rectifier is similar to that of a _______. A. trap B. regulating valve C. check valve D. filter

Last Answer : Answer: C

On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Description : On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Last Answer : Answer: B

Valve Regulated Lead Acid (VRLA) Batteries Advantages

Description : Valve Regulated Lead Acid (VRLA) Batteries Advantages

Last Answer : Valve Regulated Lead Acid (VRLA) Batteries are popularly termed as maintenance free lead acid batteries. Each cell in VRLA battery will have a value (automating operating) to allow the gas ... same voltage of the cells, to continue in using existing charging equipment VRLA batteries are economical

What is interlocks provided for the valve MCC

Description : What is interlocks provided for the valve MCC 

Last Answer : a) Mechanical interlock, which will not allow the other contactor to close if one contactor, is closed. b) 42 auxiliary contacts are wired in the control ckt. 42-1 contact in 42-2 and 42-2 contact in 42-1. 

What are the advantages of butterfly valve?

Description : What are the advantages of butterfly valve?

Last Answer : a. Less holdup. b. No support needed. c. Any actuator can be used. d. Quick opening and closing. e. Less space required. f. Used for low-pressure low temperature and large pipelines. 

How will you proceed to operate the valve manually after an electrical operation?

Description : How will you proceed to operate the valve manually after an electrical operation?  

Last Answer : After electrical operation to operate manually we must tilt the lever provided on the actuator to hand (manual) position by which the sliding clutch gets engaged with hand drive. 

Explain the operational aspects of limit switch and torque switch in rotork valve actuator.

Description : Explain the operational aspects of limit switch and torque switch in rotork valve actuator. 

Last Answer : a. When limit function is selected?  b. When torque function is selected?  Limit function - when limit function is selected in rotork valve, the limit switches will operate when the limit set ... . The limit switches will not act (only torque switch will act when selected to torque function). 

Explain how the motor motion is transmitted to the valve stem?

Description : Explain how the motor motion is transmitted to the valve stem?  

Last Answer : The motor shaft is connected to a spar gear. It engages on a worm wheel. The worm wheel has dog teeth. This dog teeth engages or hits the dig teeth on moving or sliding clutch. The ... are on the splines of valve stem. So when the sliding clutch rotates the valve also rotates simultaneously. 

What are the four basic parts of any valve actuators?

Description : What are the four basic parts of any valve actuators?

Last Answer : a. Valve motor. b. Gear mechanism. c. Limit switch and torque switch assembly. d. Terminal box. 

What are the advantages of motorised valve actuators?

Description : What are the advantages of motorised valve actuators?  

Last Answer : Advantages a. Can be used to operate in remote areas, high heat areas etc. b. Suitable logics can be wired up easily. c. Hammer blow mechanism (which will release valve in stuck open or close). The motor has high torque. 

Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions properly and trips generator #1 electrically off the bo A. Start the emergency generator. B. Ascertain cause of the low lube oil pressure. C. Strip the board of all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Description : Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions ... all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Last Answer : Answer: C

In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the same NOR and NAND inputs D. have output conditions that are exact opposites to the output condition for OR and AND, respectively

Description : In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the ... . have output conditions that are exact opposites to the output condition for OR and AND, respectively

Last Answer : Answer: D

The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Description : The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Last Answer : Answer: C

A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two back-to-back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Description : A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two ... -back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Last Answer : Answer: C

A shading coil used in an AC magnetic controller, functions to _____________. A. reduce vibration and noise in the contactor B. prevent flux buildup in the operating coil C. eliminate arcing when the contacts close D. energize the operating coil and 'pull in' the contacts

Description : A shading coil used in an AC magnetic controller, functions to _____________. A. reduce vibration and noise in the contactor B. prevent flux buildup in the operating coil C. eliminate arcing when the contacts close D. energize the operating coil and 'pull in' the contacts

Last Answer : Answer: A

What operational characteristics do the components labeled as 'S' and 'R' represent in the motor controller diagram shown in the illustration? EL-0080 A. Standard and Reverse directions B. Stop and Restart features C. Subnormal and Regular loading D. Start and Run functions

Description : What operational characteristics do the components labeled as 'S' and 'R' represent in the motor controller diagram shown in the illustration? EL-0080 A. Standard and Reverse directions B. Stop and Restart features C. Subnormal and Regular loading D. Start and Run functions

Last Answer : Answer: D

The full torque electric brake on an electric cargo winch functions to _____________. A. act as a backup brake in the event the mechanical brake should fail B. automatically hold the load as soon as current to the machine is shut off C. automatically govern the lowering speed of the load D. automatically govern the hoisting speed of the load

Description : The full torque electric brake on an electric cargo winch functions to _____________. A. act as a backup brake in the event the mechanical brake should fail B. automatically hold the load ... automatically govern the lowering speed of the load D. automatically govern the hoisting speed of the load

Last Answer : Answer: B

What are the functions of no-load current in a transformer ?

Description : What are the functions of no-load current in a transformer ?

Last Answer : No-load current produces flux and supplies iron loss and copper loss on no-load.

What are the functions of protective relays

Description : What are the functions of protective relays

Last Answer : To detect the fault and initiate the operation of the circuit breaker to isolate the defective element from the rest of the system, thereby protecting the system from damages consequent to the fault.

What are the functions of charger?

Description : What are the functions of charger? 

Last Answer : 1. For initial charging. 2. For float charging. 3. For battery equalizing charging. 4. For battery boost charging. 5. To supply normal DC loads. 

What are the sources of 240 V AC class I supply? What are the functions of each part of UPS?

Description : What are the sources of 240 V AC class I supply? What are the functions of each part of UPS? 

Last Answer : Six sources. Three 20 kVA UPS for safety related loads. Two 60 kVA UPS for non-safety related loads. One 60 kVA UPS as a standby to safety related loads. These all UPS are back up by ... UPS into service. Manual bypass To take main UPS to maintenance by putting stand by UPS into service. 

What are the functions of arc chute?

Description : What are the functions of arc chute? 

Last Answer : To increase the speed of rise of arc by magnetic action. It splits the arc by this arc resistance increases. Diagnosing the arc by cooling. 

How fibrillation current functions?

Description : How fibrillation current functions? 

Last Answer : Fibrillation current is actually function of individual body weight. For 50 kgs body weight: fibrillation current (IB) = 0.116/ª ts (Limited to 0.03 - 3 sec. Range) Where ts = duration ... is kept more because to care for under grounding services. Example laying of power cables, drainage etc. 

What are the functions of a heat exchanger?

Description : What are the functions of a heat exchanger? 

Last Answer : The function of heat exchanger is to transfer heat efficiently and economically between two fluids. Heat is transferred from the fluid, which has higher temperature to the fluid, which has lower temperature. The ... flow in heat exchangers a. Parallel flow. b. Counter flow. c. Transverse flow.

What are the functions of dearator?

Description : What are the functions of dearator?

Last Answer : Dearator removes non-condensable gases (O2), which gets added in the steam and it, mixes steam with the condensed water for feed water heating. This is a contact type feed water heater.