How will you proceed to operate the valve manually after an electrical operation?

How will you proceed to operate the valve manually after an electrical operation?  
by

1 Answer

Answer :

After electrical operation to operate manually we must tilt the lever provided on the actuator to hand (manual) position by which the sliding clutch gets engaged with hand drive. 
by

Related questions

Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Description : Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Last Answer : Ans: d

Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Last Answer : Answer: C

Which of the following conditions will occur if the solenoid coil burns out on a cargo winch with an electrical brake? A. The brake will be set by spring force. B. The motor will overspeed and burn up. C. The load suspended from the cargo boom will fall. D. Nothing will happen; the winch will continue to operate as usual.

Description : Which of the following conditions will occur if the solenoid coil burns out on a cargo winch with an electrical brake? A. The brake will be set by spring force. B. The motor will overspeed and burn ... the cargo boom will fall. D. Nothing will happen; the winch will continue to operate as usual.

Last Answer : Answer: A

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

In a power plant, coal is carried from storage place to boilers generally by means of (A) bucket (B) V-belts (C) trolleys (D) manually.

Description : In a power plant, coal is carried from storage place to boilers generally by means of (A) bucket (B) V-belts (C) trolleys (D) manually.

Last Answer : Ans: B

Equalization of the power factors of two alternators operating in parallel is accomplished _____________. A. manually, by adjusting the governor controls B. automatically, by automatic voltage regulators C. manually, adjusting the output of current transformers D. automatically, by the designed action of the governors

Description : Equalization of the power factors of two alternators operating in parallel is accomplished _____________. A. manually, by adjusting the governor controls B. automatically, by automatic voltage regulators ... the output of current transformers D. automatically, by the designed action of the governors

Last Answer : Answer: B

The 'safe switch' of the winch controller shown in the illustration is operated _______________. EL-0102 A. through the master switch handle B. when heater circuit current is high C. by contactor coil 'FR' D. manually by the winch operator

Description : The 'safe switch' of the winch controller shown in the illustration is operated _______________. EL-0102 A. through the master switch handle B. when heater circuit current is high C. by contactor coil 'FR' D. manually by the winch operator

Last Answer : Answer: D

A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit contactors when the motor develops a short circuit due to low voltage C. allow the motor to restart automatically on restoration of voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Description : A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit ... voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Last Answer : Answer: D

How does a tank-blanketing valve operate?

Description : How does a tank-blanketing valve operate?

Last Answer : Tank Blanketing Valves provide an effective means of preventing and controlling fires in flammable liquid storage tanks. Vapors cannot be ignited in the absence of an adequate supply of oxygen. In ... . The blanketing valve reseals when pressure in the tank has returned to an acceptable level.

The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Description : The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Last Answer : Answer: C

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Description : Which of the following should be the FIRST step in removing a generator from parallel operation? A. Trip the generator off the switchboard. B. Turn off all electrical equipment. C. Remove the load from the 'off going' generator. D. Increase the cycles of the generator staying on the line.

Last Answer : Answer: C

What are modes of operation of electrical drives?

Description : What are modes of operation of electrical drives?

Last Answer : Steady state Acceleration including starting Deceleration including stopping

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Description : Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Last Answer : (a) Station batteries are used to operate relay only

When the price is less than the average variable cost, the firm should …………. (a) Continue to operate till the market recover ; (b) Shut down its operation for the time being (c) Retrench workers and pay them compensation; (d) Clear the existing stock at a price less than the prevailing price to beat the competitors

Description : When the price is less than the average variable cost, the firm should . (a) Continue to operate till the market recover ; (b) Shut down its operation for the time being (c) Retrench ... compensation; (d) Clear the existing stock at a price less than the prevailing price to beat the competitors

Last Answer :  (b) Shut down its operation for the time being

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed, the head developed is maximum which is known as shut-off head (C) At a particular speed the discharge at which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Description : Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed ... which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Last Answer : (D) All the above

Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Description : Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve whereas the spring pressure tends to keep it open.( ... at idle and low speed (c)High speed/Load operation (d)Preventing backfire during cranking  

Explain operation of solenoid valve with neat diagram.

Description : Explain operation of solenoid valve with neat diagram.

Last Answer : Operation: A solenoid valve is the combination of a basic solenoid and mechanical valve. So a solenoid valve has two parts namely- Electrical solenoid, mechanical valve. Solenoid ... coil, the emf is dissipated allowing internal spring return the valve stem to the original position 

How long after energizing 'ATMX' at '41Y' shown in the illustration do the contacts of 'ATM' operate? EL-0100 A. 3 minutes B. 27 minutes C. 30 minutes D. 33 minutes

Description : How long after energizing 'ATMX' at '41Y' shown in the illustration do the contacts of 'ATM' operate? EL-0100 A. 3 minutes B. 27 minutes C. 30 minutes D. 33 minutes

Last Answer : Answer: D

What are the electrical specifications needed to operate the tanning bed?

Description : What are the electrical specifications needed to operate the tanning bed?

Last Answer : Most tanning beds require 220 volts. Most homes are not wired to supply this kind of power. It is best to call a certified electrician to install a dedicated circuit to avoid the risk of electrical overload.

How should I proceed after getting in an accident?

Description : How should I proceed after getting in an accident?

Last Answer : answer:My guess is he doesn’t have insurance. He’s trying to avoid getting in trouble with the law. However, it sounds like the damage is relatively minor. Maybe you could find replacement bumper at salvage, or on the internet somewhere.

How do you proceed after a major, jarring change in your life?

Description : How do you proceed after a major, jarring change in your life?

Last Answer : Have you talked to a therapist? Sometimes I think it's helpful to have someone to share your thoughts with and get unbiased feedback. Sorry for your loss. It is daunting to find yourself out in ... you're literally all alone when facing a crucial time period in your life must be very difficult.

How to proceed after the end of DP, when I start MD in 2 months?

Description : Hello. I need advice, maybe someone will know. At work, I reported a family house under 3 years of age. But I collected CZK 11,500, which means that in October of this year I will receive ... or something. I would otherwise be at the family house until September 2016 ... Thank you for the answers

Last Answer : Need Answer

In response to a research misconduct allegation what is the next main phase that takes place after the inquiry if there is sufficient evidence to proceed?

Description : In response to a research misconduct allegation what is the next main phase that takes place after the inquiry if there is sufficient evidence to proceed?

Last Answer : Feel Free to Answer

Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Description : Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Last Answer : Answer: B

Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency? A. A four-pole synchronous motor under normal load. B. A four-pole induction motor under no load. C. A six-pole synchronous motor under normal load. D. A six-pole induction motor under full load.

Description : Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency? A. A four-pole synchronous motor under normal load. B. A four-pole induction motor under ... A six-pole synchronous motor under normal load. D. A six-pole induction motor under full load.

Last Answer : Answer: A

Universal motors will operate on AC or DC current, and are generally found in _____________. A. portable tools B. large pump motors C. turbo electric main motors D. forced draft fans

Description : Universal motors will operate on AC or DC current, and are generally found in _____________. A. portable tools B. large pump motors C. turbo electric main motors D. forced draft fans

Last Answer : Answer: A

A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately ___________. A. 850 RPM B. 1,150 RPM C. 1,750 RPM D. 3,550 RPM

Description : A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately ___________. A. 850 RPM B. 1,150 RPM C. 1,750 RPM D. 3,550 RPM

Last Answer : Answer: C

If the energy input is significantly reduced to the prime mover of one shipboard alternator operating in parallel with others, that alternator will _____________. A. continue to operate at no load B. lose its load and overspeed C. begin to motorize and then trip out D. slow down and operate at reduced load

Description : If the energy input is significantly reduced to the prime mover of one shipboard alternator operating in parallel with others, that alternator will _____________. A. continue to operate at no load B. lose ... overspeed C. begin to motorize and then trip out D. slow down and operate at reduced load

Last Answer : Answer: C

If field excitation is suddenly lost to an alternator operating in parallel, that alternator will _____________. A. supply excessive current to the bus B. operate at the same load, but with reduced voltage C. lose its load and tend to overspeed D. become overloaded and slow down

Description : If field excitation is suddenly lost to an alternator operating in parallel, that alternator will _____________. A. supply excessive current to the bus B. operate at the same load, but with reduced voltage C. lose its load and tend to overspeed D. become overloaded and slow down

Last Answer : Answer: C

The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. contactor coil '3M' has many shorted turns B. resistor 'R8-A2' has an open C. contacts '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Last Answer : Answer: B

If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Description : If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Last Answer : Answer: A

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Last Answer : Answer: B

Modern handheld digital tachometers operate by counting light pulses returned to the unit by ______________. A. the tach generator B. either the coupling or shaft C. a small bulb attached to the shaft D. a piece of reflective tape

Description : Modern handheld digital tachometers operate by counting light pulses returned to the unit by ______________. A. the tach generator B. either the coupling or shaft C. a small bulb attached to the shaft D. a piece of reflective tape

Last Answer : Answer: D

Why is it desirable to operate paralleled AC generators at the same power factor? A. Circulating currents are kept to a minimum. B. Field excitation losses are kept to a minimum. C. Generator rotors will have a lesser tendency to hunt. D. Because a power factor increase will decrease kilowatt output.

Description : Why is it desirable to operate paralleled AC generators at the same power factor? A. Circulating currents are kept to a minimum. B. Field excitation losses are kept to a minimum. C. Generator ... will have a lesser tendency to hunt. D. Because a power factor increase will decrease kilowatt output.

Last Answer : Answer: A

Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Description : Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Last Answer : Answer: A

As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Description : As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Last Answer : Answer: C

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Last Answer : Answer: B

Shunt, series, and compound wound motors, are all DC motors designed to operate from _____________. A. constant potential, variable current DC sources B. variable potential, constant current DC sources C. variable potential, variable current DC sources D. constant potential, constant current DC sources

Description : Shunt, series, and compound wound motors, are all DC motors designed to operate from _____________. A. constant potential, variable current DC sources B. variable potential, constant current DC ... C. variable potential, variable current DC sources D. constant potential, constant current DC sources

Last Answer : Answer: A

Power necessary to operate the horn shown in the illustration _____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through a relay coil D. also lights lamps 'R' and 'T'

Description : Power necessary to operate the horn shown in the illustration _____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through a relay coil D. also lights lamps 'R' and 'T'

Last Answer : Answer: B

How many different D.C. voltages are required to operate the circuit shown in the illustration? EL-0094 A. Two B. Three C. Four D. Five

Description : How many different D.C. voltages are required to operate the circuit shown in the illustration? EL-0094 A. Two B. Three C. Four D. Five

Last Answer : Answer: C

On AC vessels, which of the following statements represents the most difficult problem involved in obtaining a DC potential suitable for use by computer components? A. A stepdown transformer is always required. B. Vessel vibrations affect the voltage source. C. The voltage must be rectified and made ripple free. D. Rectifiers cannot operate with voltage regulators.

Description : On AC vessels, which of the following statements represents the most difficult problem involved in obtaining a DC potential suitable for use by computer components? A. A stepdown transformer is ... voltage must be rectified and made ripple free. D. Rectifiers cannot operate with voltage regulators.

Last Answer : Answer: C