Description : Splines are keys. a) True b) False
Last Answer : a) True
Description : The muscle spindles: a. are extrafusal fibres b. are innervated by type Ia and II fibres c. received motor innervation from the gamma fibres. d. respond to tension in the muscle
Last Answer : are innervated by type Ia and II fibres
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Last Answer : b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are individually true and R is the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False
Description : Hydrostatic and hydrodynamic lubrication are the same thing. a) True b) False
Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. a) True b) False
Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. a) True b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False
Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False
Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False
Description : . In gear boxes and small size motors, rolling contact bearings are used. a) True b) False
Description : In steam and gas turbines, rolling contact bearings are used. a) True b) False
Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False
Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False
Description : Belleville spring can be used in clutch application. a) True b) False
Description : Nipping is defined as leaving the gap between full length leaf and graduated length leaf. a) True b) False
Description : Nip is the initial gap between extra full length leaf and the graduated length leaf before the assembly. a) True b) False
Description : The strip of spiral spring is never subjected to pure bending moment. a) True b) False
Description : Surge is a desirable effect in the sprigs. a) True b) False
Description : Surge is caused by resonance effect in the spring. a) True b) False
Description : Can concentric springs be used to obtain a force which is not proportional to its deflection? a) True b) False