Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring
Last Answer : (D) Square of wire diameter of each spring
Description : In concentric springs, vibrations called surge are amplified. a) True b) False
Last Answer : b) False
Description : For two springs connected in series, the net deflection is equal to the sum of deflection in two springs. a) True b) False
Last Answer : a) True
Description : A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above
Last Answer : (C) both springs always have opposite hand of helices
Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs
Last Answer : (D) Concentric springs
Description : Concentric springs are used, (A) To achieve greater load carrying capacity with given space (B) To achieve fail-safe system (C) To eliminate surge (D) Any of the above objectives
Last Answer : (D) Any of the above objectives
Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined
Last Answer : b) Double force
Description : For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False
Description : Martin’s factor compensates for curvature effect in springs. a) True b) False
Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False
Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l
Last Answer : d) Frictional torque is given by fpr2l
Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N
Last Answer : (c) 689.7N and 4310.3N
Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2
Last Answer : (C) Crushing load or columns is less than the buckling load
Description : In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same
Last Answer : (A) shorten the spring
Description : Springs are used, (A) To absorb shocks and vibrations (B) To store and release energy (C) To measure force (D) For any of the above functions
Last Answer : (D) For any of the above functions
Description : In hydrodynamic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above
Last Answer : (A) The axis of journal is eccentric with respect to axis of bearing
Description : In hydrostatic bearing, (A) The axis of journal is eccentric with respect to axis of bearing (B) The axis of journal is concentric with respect to axis of bearing (C) The axis can be either eccentric or concentric depending upon speed (D) None of the above
Last Answer : (B) The axis of journal is concentric with respect to axis of bearing
Description : The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above
Last Answer : (D) all of the above
Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (C) Ratio of mean coil diameter to wire diameter
Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (D) Force required to produce unit deflection
Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. a) One fourth deflection b) Double deflection c) Four time deflection d) None of the listed
Last Answer : b) Double deflection
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm
Last Answer : c. 5mm
Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False
Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined
Last Answer : (b) Double force
Description : Cocentric springs are used in (A) Heavy duty diesel engines (B) aircraft engines (C) railroad suspensions (D) all of the above
Description : Factor of safety in the design of springs is usually (A) 1.5 or less (B) 3 or less (C) 4.5 or less (D) 6 or less
Last Answer : (A) 1.5 or less
Description : For two springs in parallel, effective stiffness (k) is Where k 1 & k 2 are stiffness of springs 1 & 2 respectively (A) k 1 k 2 / (k 1 + k 2 ) (B) k 1 + k 2 (C) k 1 k 2 (D) (k 1 + k 2 ) / k 1 k 2
Last Answer : (B) k 1 + k 2
Description : For two springs in series, effective stiffness (k) is Where k 1 & k 2 are stiffness of springs 1 & 2 respectively (A) k 1 k 2 / (k 1 + k 2 ) (B) k 1 + k 2 (C) k 1 k 2 (D) (k 1 + k 2 ) / k 1 k 2
Last Answer : (A) k 1 k 2 / (k 1 + k 2 )
Description : Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above
Last Answer : (C) both (A) and (B)
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : Two springs of stiffness k1 and k2 are connected in series, the combined (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2
Last Answer : (A) k1k2/k1 + k2
Description : Two springs of stiffness k1 and k2 are connected in parallel, the combined stiffness of the connection is given by, (A) k1k2/k1 + k2 (B) k1k2/k1 - k2 (C) k1 + k2 (D) k1 + k2/k1k2
Last Answer : (C) k1 + k2
Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C
Last Answer : (A) (4C - 1/4C - 4) + 0.615/C
Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant
Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact
Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (D) Where there is no lubricant
Description : The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4
Last Answer : (A) Pδ/2
Description : The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring
Last Answer : (C) Belleville (coned disk) spring
Description : Belleville spring can only produce linear load deflection characteristics. a) Only linear b) Linear as well as non linear c) Non-linear d) None of the mentioned
Last Answer : b) Linear as well as non linear
Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ
Last Answer : b) 8PDɜN/Gd4
Description : The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root
Last Answer : b) No, it is directly proportional
Description : A sliding contact bearing is operating under stable condition. The pressure developed in oil film is p when the journal rotates at N rpm. The dynamic viscosity of lubricant is μ and effective coefficient of ... to p and f) (d) f is directly proportional to μ and inversely proportional to N
Last Answer : (b) f is directly proportional to μ and N
Description : Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. ... 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only
Last Answer : (a) 1, 2, 3 and 4
Description : The angle of twist for a transmission shaft is inversely proportional to (A) Shaft diameter (B) (Shaft diameter)2 (C) (Shaft diameter)3 (D) (Shaft diameter)4
Last Answer : (D) (Shaft diameter)4
Description : Maximum displacement due to forced vibration is dependent on deflection due to static force. a) True b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion A: Large size stones are required in stone revetment in shore protection. Reason R: Resistance of stone to wave force is proportional to its volume and wave force is proportional to the exposed area of the stone. ... of A (C) A is true but R is false (D) A is false but R is true
Last Answer : (A) Both A and R is true and R is the correct explanation of A
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False